Nickolay V. Shmyrev napsal(a):
Thanks for your suggestion, but It shouldn't be hardware related, It is randomly changing after restart or shutdown.В Вск, 17/06/2007 в 14:02 +0200, Mirek Slugeň пишет:Hi, Is my problem with saa7134 and FM radio related to this mailing-list? If not, can someone point me to correct mailing-list? Both cards works without any problems in Windows XP, I have even third card with same errors. After more investigation I think It is problem with analog sound, not only analog radio, on problematic card I can't get any sound while recording via mencoder. I am using this command to record tv: mencoder tv:// -tv driver=v4l2:device=/dev/video0:freq=711,25:alsa:adevice=hw.1,0:amode=1:audiorate=32000:forceaudio:volume=100:immediatemode=0:width=720:height=576:normid=1:input=0 \ -oac mp3lame -vf field=0,scale=360:288,harddup -ovc lavc -ovc lavc -lavcopts vcodec=mpeg4:aspect=4/3:vqscale=1 -ofps 25 -o /test.avi I am sending log after some restarts, now works only first card, and not second, DVB-T and DVB-S works on both cards without any problem. PS: I am from Czech Republic, we have here some PAL norm. Mirek |
saa7133[1]: dsp access error saa7133[1]: dsp access error tda1004x: setting up plls for 48MHz sampling clock saa7133[1]: dsp access error saa7133[1]: dsp access error saa7133[0]/audio: tvaudio thread scan start [3] saa7133[0]/audio: FM Radio tda1004x: found firmware revision 29 -- ok tda827x_probe_version: could not read from tuner at addr: 0xc0 tda827xo_set_params: could not write to tuner at addr: 0xc0 saa7133[1]: dsp access error saa7133[1]: dsp access error saa7133[1]/audio: tvaudio thread scan start [4] saa7133[1]/audio: FM Radio saa7133[1]: dsp access error saa7133[1]: dsp access error saa7133[1]: dsp access error saa7133[1]: dsp access error saa7133[1]: dsp access error tda827xo_set_params: could not write to tuner at addr: 0xc0 saa7133[0]/audio: tvaudio thread status: 0x102011 [FM radio / IF sel / 50 deemp] saa7133[0]/audio: detailed status: ###### BTSC stereo noise mute ####### init done tda827xo_set_params: could not write to tuner at addr: 0xc0 tda827xo_set_params: could not write to tuner at addr: 0xc0 saa7133[1]/audio: tvaudio thread status: 0x100000 [no standard detected] saa7133[1]/audio: detailed status: ############# init done tda827xo_set_params: could not write to tuner at addr: 0xc0 tda827x_probe_version: could not read from tuner at addr: 0xc0 saa7134 ALSA driver for DMA sound unloaded Linux video capture interface: v2.00 saa7130/34: v4l2 driver version 0.2.14 loaded saa7133[0]: found at 0000:06:02.0, rev: 209, irq: 21, latency: 64, mmio: 0xef9ef000 saa7133[0]: subsystem: 5168:0319, board: LifeView FlyDVB Trio [card=84,autodetected] saa7133[0]: board init: gpio is 11400 saa7133[0]: i2c eeprom 00: 68 51 19 03 54 20 1c 00 43 43 a9 1c 55 d2 b2 92 saa7133[0]: i2c eeprom 10: 00 00 60 0a ff 20 ff ff ff ff ff ff ff ff ff ff saa7133[0]: i2c eeprom 20: 01 40 01 03 03 01 01 03 08 ff 01 f9 ff ff ff ff saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[0]: i2c eeprom 40: ff 00 10 c0 96 12 08 00 c2 96 c6 1c 16 3a 15 ff saa7133[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[0]/audio: tvaudio thread scan start [1] saa7133[0]/audio: scanning: B/G D/K I tuner 1-004b: chip found @ 0x96 (saa7133[0]) tuner 1-004b: setting tuner address to 61 tuner 1-004b: type set to tda8290+75a tuner 1-004b: setting tuner address to 61 tuner 1-004b: type set to tda8290+75a saa7133[0]: registered device video0 [v4l2] saa7133[0]: registered device vbi0 saa7133[0]: registered device radio0 saa7133[0]/audio: tvaudio thread status: 0x100000 [no standard detected] saa7133[0]/audio: detailed status: ############# init done saa7133[1]: found at 0000:06:04.0, rev: 208, irq: 16, latency: 64, mmio: 0xef9ef800 saa7133[1]: subsystem: 5168:0319, board: LifeView FlyDVB Trio [card=84,autodetected] saa7133[1]: board init: gpio is 11400 tuner 2-004b: chip found @ 0x96 (saa7133[1]) tuner 2-004b: setting tuner address to 61 tuner 2-004b: type set to tda8290+75a tuner 2-004b: setting tuner address to 61 tuner 2-004b: type set to tda8290+75a saa7133[1]: i2c eeprom 00: 68 51 19 03 54 20 1c 00 43 43 a9 1c 55 d2 b2 92 saa7133[1]: i2c eeprom 10: 00 00 60 0a ff 20 ff ff ff ff ff ff ff ff ff ff saa7133[1]: i2c eeprom 20: 01 40 01 03 03 01 01 03 08 ff 01 f9 ff ff ff ff saa7133[1]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[1]: i2c eeprom 40: ff 00 10 c0 96 12 08 00 c2 96 c6 1c 16 3a 15 ff saa7133[1]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[1]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[1]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[1]: dsp access error saa7133[1]: dsp access error saa7133[1]: dsp access error saa7133[1]: dsp access error saa7133[1]: dsp access error saa7133[1]: dsp access error saa7133[1]: registered device video1 [v4l2] saa7133[1]: registered device vbi1 saa7133[1]: registered device radio1 saa7133[1]: dsp access error saa7133[1]: dsp access error saa7133[1]/audio: tvaudio thread scan start [1] saa7133[1]/audio: scanning: B/G D/K I saa7133[1]: dsp access error saa7133[1]: dsp access error saa7133[1]: dsp access error saa7133[1]: dsp access error saa7133[0]/dvb: frontend initialization failed saa7133[1]/dvb: frontend initialization failed saa7134 ALSA driver for DMA sound loaded saa7133[0]/alsa: saa7133[0] at 0xef9ef000 irq 21 registered as card -1 saa7133[1]/alsa: saa7133[1] at 0xef9ef800 irq 16 registered as card -1 saa7133[1]/audio: tvaudio thread status: 0x100000 [no standard detected] saa7133[1]/audio: detailed status: ############# init done saa7134 ALSA driver for DMA sound unloaded Linux video capture interface: v2.00 saa7130/34: v4l2 driver version 0.2.14 loaded saa7133[0]: found at 0000:06:02.0, rev: 209, irq: 21, latency: 64, mmio: 0xef9ef000 saa7133[0]: subsystem: 5168:0319, board: LifeView FlyDVB Trio [card=84,autodetected] saa7133[0]: board init: gpio is 211400 saa7133[0]: i2c eeprom 00: 68 51 19 03 54 20 1c 00 43 43 a9 1c 55 d2 b2 92 saa7133[0]: i2c eeprom 10: 00 00 60 0a ff 20 ff ff ff ff ff ff ff ff ff ff saa7133[0]: i2c eeprom 20: 01 40 01 03 03 01 01 03 08 ff 01 f9 ff ff ff ff saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[0]: i2c eeprom 40: ff 00 10 c0 96 12 08 00 c2 96 c6 1c 16 3a 15 ff saa7133[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[0]/audio: tvaudio thread scan start [1] saa7133[0]/audio: scanning: B/G D/K I tuner 1-004b: chip found @ 0x96 (saa7133[0]) tuner 1-004b: setting tuner address to 61 tuner 1-004b: type set to tda8290+75a tuner 1-004b: setting tuner address to 61 tuner 1-004b: type set to tda8290+75a saa7133[0]: registered device video0 [v4l2] saa7133[0]: registered device vbi0 saa7133[0]: registered device radio0 saa7133[0]/audio: tvaudio thread status: 0x100000 [no standard detected] saa7133[0]/audio: detailed status: ############# init done saa7133[1]: found at 0000:06:04.0, rev: 208, irq: 16, latency: 64, mmio: 0xef9ef800 saa7133[1]: subsystem: 5168:0319, board: LifeView FlyDVB Trio [card=84,autodetected] saa7133[1]: board init: gpio is 211400 tuner 2-004b: chip found @ 0x96 (saa7133[1]) tuner 2-004b: setting tuner address to 61 tuner 2-004b: type set to tda8290+75a tuner 2-004b: setting tuner address to 61 tuner 2-004b: type set to tda8290+75a saa7133[1]: i2c eeprom 00: 68 51 19 03 54 20 1c 00 43 43 a9 1c 55 d2 b2 92 saa7133[1]: i2c eeprom 10: 00 00 60 0a ff 20 ff ff ff ff ff ff ff ff ff ff saa7133[1]: i2c eeprom 20: 01 40 01 03 03 01 01 03 08 ff 01 f9 ff ff ff ff saa7133[1]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[1]: i2c eeprom 40: ff 00 10 c0 96 12 08 00 c2 96 c6 1c 16 3a 15 ff saa7133[1]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[1]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[1]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[1]: dsp access error saa7133[1]: dsp access error saa7133[1]: dsp access error saa7133[1]: dsp access error saa7133[1]: dsp access error saa7133[1]: dsp access error saa7133[1]: registered device video1 [v4l2] saa7133[1]: registered device vbi1 saa7133[1]: registered device radio1 saa7133[1]: dsp access error saa7133[1]: dsp access error saa7133[1]/audio: tvaudio thread scan start [1] saa7133[1]/audio: scanning: B/G D/K I saa7133[1]: dsp access error saa7133[1]: dsp access error saa7133[1]: dsp access error saa7133[1]: dsp access error DVB: registering new adapter (saa7133[0]) DVB: registering frontend 0 (Philips TDA10046H DVB-T)... tda1004x: setting up plls for 48MHz sampling clock tda1004x: found firmware revision 29 -- ok DVB: registering new adapter (saa7133[1]) DVB: registering frontend 1 (Philips TDA10046H DVB-T)... tda1004x: setting up plls for 48MHz sampling clock tda1004x: setting up plls for 48MHz sampling clock saa7133[1]/audio: tvaudio thread status: 0x100000 [no standard detected] saa7133[1]/audio: detailed status: ############# init done saa7133[1]: dsp access error saa7133[1]: dsp access error saa7133[0]/audio: tvaudio thread scan start [2] saa7133[0]/audio: FM Radio tda1004x: found firmware revision 29 -- ok tda1004x: found firmware revision 29 -- ok saa7134 ALSA driver for DMA sound loaded saa7133[0]/alsa: saa7133[0] at 0xef9ef000 irq 21 registered as card -1 saa7133[1]/alsa: saa7133[1] at 0xef9ef800 irq 16 registered as card -1 saa7133[1]: dsp access error saa7133[1]: dsp access error saa7133[1]/audio: tvaudio thread scan start [2] saa7133[1]/audio: FM Radio saa7133[1]: dsp access error saa7133[1]: dsp access error saa7133[1]: dsp access error saa7133[1]: dsp access error saa7133[1]: dsp access error tda1004x: setting up plls for 48MHz sampling clock saa7133[0]/audio: tvaudio thread status: 0x102811 [FM radio / IF sel / 50 deemp] saa7133[0]/audio: detailed status: #### BTSC/FM radio pilot ## BTSC stereo noise mute ####### init done tda1004x: found firmware revision 29 -- ok saa7133[1]/audio: tvaudio thread status: 0x100000 [no standard detected] saa7133[1]/audio: detailed status: ############# init done saa7133[1]: dsp access error saa7133[1]: dsp access error saa7133[1]: dsp access error saa7133[1]: dsp access error saa7133[1]: dsp access error saa7133[1]: dsp access error saa7133[1]: dsp access error saa7133[1]: dsp access error saa7133[0]/audio: tvaudio thread scan start [3] saa7133[0]/audio: FM Radio saa7133[1]: dsp access error saa7133[1]: dsp access error saa7133[1]/audio: tvaudio thread scan start [3] saa7133[1]/audio: FM Radio saa7133[1]: dsp access error saa7133[1]: dsp access error saa7133[1]: dsp access error saa7133[1]: dsp access error saa7133[1]: dsp access error tda1004x: setting up plls for 48MHz sampling clock saa7133[0]/audio: tvaudio thread status: 0x102811 [FM radio / IF sel / 50 deemp] saa7133[0]/audio: detailed status: #### BTSC/FM radio pilot ## BTSC stereo noise mute ####### init done tda1004x: found firmware revision 29 -- ok saa7133[1]/audio: tvaudio thread status: 0x100000 [no standard detected] saa7133[1]/audio: detailed status: ############# init done saa7133[1]: dsp access error saa7133[1]: dsp access error saa7133[1]: dsp access error saa7133[1]: dsp access error tda1004x: setting up plls for 48MHz sampling clock saa7133[1]: dsp access error saa7133[1]: dsp access error saa7133[0]/audio: tvaudio thread scan start [4] saa7133[0]/audio: FM Radio tda1004x: found firmware revision 29 -- ok saa7133[1]/audio: tvaudio thread scan start [4] saa7133[1]/audio: FM Radio saa7133[1]: dsp access error saa7133[1]: dsp access error saa7133[1]: dsp access error saa7133[1]: dsp access error saa7133[1]: dsp access error saa7133[1]: dsp access error saa7133[1]: dsp access error tda1004x: setting up plls for 48MHz sampling clock saa7133[0]/audio: tvaudio thread status: 0x102811 [FM radio / IF sel / 50 deemp] saa7133[0]/audio: detailed status: #### BTSC/FM radio pilot ## BTSC stereo noise mute ####### init done tda1004x: found firmware revision 29 -- ok saa7133[1]/audio: tvaudio thread status: 0x100000 [no standard detected] saa7133[1]/audio: detailed status: ############# init done
_______________________________________________ linux-dvb mailing list [email protected] http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
