-----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Nathan Faust Sent: Wednesday, September 05, 2007 2:17 PM To: Michael Krufky Cc: linux-dvb@linuxtv.org Subject: Re: [linux-dvb] cx88-dvb: fix nxt200x rf input switching broke my tuner? :)
-----Original Message----- From: Michael Krufky [mailto:[EMAIL PROTECTED] Sent: Wednesday, September 05, 2007 2:07 PM To: Nathan Faust Cc: CityK; linux-dvb@linuxtv.org Subject: Re: [linux-dvb] cx88-dvb: fix nxt200x rf input switching broke my tuner? :) > -----Original Message----- > From: CityK [mailto:[EMAIL PROTECTED] > Sent: Wednesday, September 05, 2007 1:33 PM > To: Nathan Faust > Cc: linux-dvb@linuxtv.org > Subject: Re: [linux-dvb] cx88-dvb: fix nxt200x rf input switching broke > my tuner? :) > > Nathan Faust wrote: >> Hi, >> >> I've notice the same thing with my Kworld ATSC-110. >> I'm running Ubuntu 7.10, 2.6.22-10-generic, x86_64. I guess it is a >> change in the 2.6.22 kernel. >> Is there anyway to change this back so that QAM and NTSC inputs are >> the same? >> > > They should be the same now -- that was what the change was all about. > > By default now, the top RF input should be 8VSB and the bottom should be > QAM & analog (both ota and cable). Nathan Faust wrote: > CityK, > > Thanks for your reply, but that is not what I'm seeing in MythTV and > TVTime for /dev/video0. I'm getting signal from /dev/video0 when I use > the upper input, not the lower one. I haven't trying tuning 8VSB, but > as for the QAM input, that seems to be working as expected. > > Maybe I should look at the driver config for input select in SAA7134 or > swap the input selection lines for VSB and QAM in the dvb code? > > After looking at the input selection code in nxt200x.c, QAM and VSB, it > looks like if I switch these lines it will swap the inputs. > //QAM > - state->config->set_pll_input(buf+1, 1); > + state->config->set_pll_input(buf+1, 0); > > //VSB > - state->config->set_pll_input(buf+1, 0); > + state->config->set_pll_input(buf+1, 1); > > Am I correct? > > I am confused as to what these lines do > if (state->config->set_ts_params) > state->config->set_ts_params(fe, 1); <-- what the front-end > parameter 0 or 1 mean. Nathan, Please do not top-quote.... As per your description above, you are correct... HOWEVER, now I understand your issue -- you are running old code. If you update to the latest v4l/dvb modules via linuxtv.org mercurial, you will find that functionality has been restored as per your desire. Please see http://linuxtv.org/repo ...for instructions to upgrade your v4l/dvb modules. Good Luck, Mike ------------------------ Mike, I've been using the stock Ubuntu 7.10 kernel (2.6.22.4) with just the Kworld ATSC-110 remote additions. I'll give that a try and get back if I continue to have problems. As for top quoting, sorry about that. Thank you, Nathan. ----------------------- Mike, I'm working on compiling the current v4l-dvb kernel modules (v4l-dvb-0c3e99a3f31c). Do you know if the Kworld ATSC-110 remote patch is merged into the code or do I need to run the patch, http://www.mythtv.org/wiki/index.php/User:Vprada#Kernel_Modification ? I couldn't find any mention of the remote code in the source, assuming that it needs patching still. Thank you, Nathan. _______________________________________________ linux-dvb mailing list linux-dvb@linuxtv.org http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
