On 10/5/07, David Campbell <[EMAIL PROTECTED]> wrote: > The whole XP driver kit is at http://www.aaa.net.au/campbell/driver.zip > but it may support other devices so unsure what bits are actually relevant: > > -rw-rw-r-- 1 dcampbel dcampbel 4697 2005-08-06 15:27 EMAUDIO.INF > -rw-rw-r-- 1 dcampbel dcampbel 20736 2005-07-08 17:43 emAudio.sys > -rw-rw-r-- 1 dcampbel dcampbel 48335 2005-11-14 20:29 EMBDA.INF > -rw-rw-r-- 1 dcampbel dcampbel 209664 2005-11-14 20:30 emBDA.sys > -rw-rw-r-- 1 dcampbel dcampbel 17152 2005-11-14 20:29 emOEM.sys > ("strings" indicates it to be an MT2060 driver) > -rw-rw-r-- 1 dcampbel dcampbel 32768 2005-11-14 20:29 emPRP.ax
Interesting. > >> The driver finds it but doesn't seem to recognise one of the i2c > >> devices: em28xx #0: found i2c device @ 0x16 [???] > >> > > > > That's the ZL10353. I think it's the analog code that's not detecting > > it; it's the digital part of the driver that handles this i2c device, > > and it doesn't auto-detect. > > > Actually this unrecognised device shows itself at different i2c > addresses different times you plug it in. See below for what I've seen. > > em28xx #0: found i2c device @ 0x26 [???] > em28xx #0: found i2c device @ 0xa0 [eeprom] > em28xx #0: found i2c device @ 0xc2 [tuner (analog)] > > em28xx #0: found i2c device @ 0x16 [???] > em28xx #0: found i2c device @ 0xa0 [eeprom] > em28xx #0: found i2c device @ 0xc2 [tuner (analog)] > > em28xx #0: found i2c device @ 0x32 [???] > em28xx #0: found i2c device @ 0xa0 [eeprom] > em28xx #0: found i2c device @ 0xc2 [tuner (analog)] I'm guessing it's probably bogus, then. > I find that if I do the following, the device gets registered, and it is > saying something about an LG chip but I'm not familiar enough with the > depths of the driver to know whether this output below is actually the > driver detecting the tuner chipset, or something that the driver has > been forced to believe. Can you comment? > > modprobe em28xx card=8 i2c_scan=1 device_mode=1 > > Table at 0x04, strings=0x226a, 0x0000, 0x0000 > tuner 1-0061: chip found @ 0xc2 (em28xx #0) > attach inform (default): detected I2C address c2 > tuner 0x61: Configuration acknowledged > tuner 1-0061: type set to 37 (LG PAL (newer TAPC series)) > em28xx #0: found i2c device @ 0x26 [???] > em28xx #0: found i2c device @ 0xa0 [eeprom] > em28xx #0: found i2c device @ 0xc2 [tuner (analog)] > em28xx #0: V4L2 device registered as /dev/video0 > em28xx #0: Found Pinnacle PCTV USB 2 You're basically forcing the driver to assume that your tuner is that particular one. I'm guessing the LG tuner it's set to is a can tuner, which is far too big to be in a USB device. I'd suggest that "Terratec Cinergy T XS (MT2060)" or "Pinnacle PCTV DVB-T" would be a better choice. > but subsequently loading the em2880-dvb device doesn't work.... I don't > know whether I'm doing the right thing here by attempting to load this: > > em2880-dvb.c: DVB Init > em2880-dvb.c: unsupported device > em2880-dvb.c: failed initializing zl10353 DVB-T demodulator > em2880-dvb.c: retrying with mt352 DVB-T demodulator > FIXME:em28xx_i2c_send_bytes(1e): write failed: > =============================== > 7f > ================================ > mt352_read_register: readreg error (reg=127, ret==-19) > em2880-dvb.c: no luck with mt352 demodulator, not attaching em2880-dvb > em2880-dvb.c: DVB-T demodulator not reachable, did you try "modprobe > em28xx device_mode=1" > Em28xx: Initialized (Em2880 DVB Extension) extension That's because you're telling the driver that your device is one that doesn't support DVB-T; I'm not sure why it even tries to load. (The fact that it doesn't do the right GPIO-twiddling doesn't help either.) > > Aidan > Markus Rechberger wrote: > > This device requires a gpio setup for enabling the zl10353 on the i2c bus. > > > Does your driver already do that for some devices? How difficult is it > going to be to convince it for this one? It's not that hard (in theory); it just requires booting into Windows and running a USB sniffer to find out what the Windows driver sends. It's just that it's different for different devices. I'm sure Markus will tell you more. Aidan _______________________________________________ linux-dvb mailing list linux-dvb@linuxtv.org http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
