I try to use it on my ubuntu hardy machine for video capture mainly and mpeg2 stream encoding (have no interest in using tvtuner yet)
chipset seems to be Conexant CX23885+CX23416 and xceive3028 http://www.leadtek.com/eng/tv_tuner/specification.asp?pronameid=351&lineid=6&act=2 I installed mercurial and cx23885 drivers are up to date but the card is not in the cards list and even if i force it with insmod card=4 for example doesn't work (hauppage firmware detection issues) What should i do next? , patch the driver and add support for this card (i have seen an old thread with pvr3200 but i don't know what is happened next) Any help is welcomed sudo modprobe -r cx23885 sudo modprobe cx23885 i2c_scan=1 [127661.326509] cx23885 driver version 0.0.1 loaded [127661.326585] ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 16 [127661.326590] cx23885[0]: Your board isn't known (yet) to the driver. You can [127661.326591] cx23885[0]: try to pick one of the existing card configs via [127661.326592] cx23885[0]: card=<n> insmod option. Updating to the latest [127661.326593] cx23885[0]: version might help as well. [127661.326595] cx23885[0]: Here is a list of valid choices for the card=<n> insmod option: [127661.326597] cx23885[0]: card=0 -> UNKNOWN/GENERIC [127661.326599] cx23885[0]: card=1 -> Hauppauge WinTV-HVR1800lp [127661.326601] cx23885[0]: card=2 -> Hauppauge WinTV-HVR1800 [127661.326602] cx23885[0]: card=3 -> Hauppauge WinTV-HVR1250 [127661.326604] cx23885[0]: card=4 -> DViCO FusionHDTV5 Express [127661.326611] CORE cx23885[0]: subsystem: 107d:6f21, board: UNKNOWN/GENERIC [card=0,autodetected] [127661.426670] cx23885[0]: i2c bus 0 registered [127661.430127] cx23885[0]: i2c scan: found device @ 0x30 [???] [127661.437848] cx23885[0]: i2c scan: found device @ 0xa0 [eeprom] [127661.444354] cx23885[0]: i2c bus 1 registered [127661.457866] cx23885[0]: i2c scan: found device @ 0xc2 [tuner/mt2131/tda8275] [127661.462028] cx23885[0]: i2c bus 2 registered [127661.463969] cx23885[0]: i2c scan: found device @ 0x66 [???] [127661.464603] cx23885[0]: i2c scan: found device @ 0x88 [cx25837] [127661.464902] cx23885[0]: i2c scan: found device @ 0x98 [???] [127661.493846] cx23885[0]/0: found at 0000:02:00.0, rev: 2, irq: 16, latency: 0, mmio: 0xcfa00000 [127661.493856] PCI: Setting latency timer of device 0000:02:00.0 to 64 lspci -vvv 02:00.0 Multimedia video controller: Conexant Unknown device 8852 (rev 02) Subsystem: LeadTek Research Inc. Unknown device 6f21 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0, Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 16 Region 0: Memory at cfa00000 (64-bit, non-prefetchable) [size=2M] Capabilities: [40] Express Endpoint IRQ 0 Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag- Device: Latency L0s <64ns, L1 <1us Device: AtnBtn- AtnInd- PwrInd- Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported- Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ Device: MaxPayload 128 bytes, MaxReadReq 512 bytes Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 0 Link: Latency L0s <2us, L1 <4us Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch- Link: Speed 2.5Gb/s, Width x1 Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [90] Vital Product Data Capabilities: [a0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable- Address: 0000000000000000 Data: 0000 -- developer flamerobin.org
_______________________________________________ linux-dvb mailing list linux-dvb@linuxtv.org http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb