Any suggestions ? Thanks Guillaume
On Wed, Feb 20, 2008 at 1:58 AM, Guillaume Membré <[EMAIL PROTECTED]> wrote: > Hello, > > I finally found that unplugging and plugging my pci card suppresses > the kernel errors. > > However, I didn't find any channels with an initial tuning file for my > cable provider in France so I tried w_scan and it didn't find anything > either. > $ w_scan -fc > w_scan version 20080105 > Info: using DVB adapter auto detection. > Found DVB-C frontend. Using adapter /dev/dvb/adapter0/frontend0 > -_-_-_-_ Getting frontend capabilities-_-_-_-_ > frontend Philips TDA10023 DVB-C supports > INVERSION_AUTO > QAM_AUTO not supported, trying QAM_64 and QAM_256. > FEC_AUTO > -_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_ > 50500: > [.....] > 858000: > ERROR: Sorry - i couldn't get any working frequency/transponder > Nothing to scan!! > > dumping lists (0 services) > Done. > > Under windows, the program shipped with my card found 85 channels and it > works. > > what's wrong ? please help ! > Guillaume > > > > > On Feb 15, 2008 11:02 PM, Guillaume Membré <[EMAIL PROTECTED]> wrote: > > Hello, > > > > I'm trying to setup a Satelco easy watch dvb-c but it doesn't work : > > when doing a scan with the following command : > > $ scan fr-noos-numericable > > scanning fr-noos-numericable > > using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0' > > initial transponder 147000000 6875000 0 3 > > >>> tune to: 147000000:INVERSION_AUTO:6875000:FEC_NONE:QAM_64 > > WARNING: >>> tuning failed!!! > > >>> tune to: 147000000:INVERSION_AUTO:6875000:FEC_NONE:QAM_64 (tuning > failed) > > WARNING: >>> tuning failed!!! > > ERROR: initial tuning failed > > dumping lists (0 services) > > Done. > > > > the kernel shows the following errors : > > DVB: TDA10023(0): tda10023_writereg, writereg error (reg == 0x10, val > > == 0x00, ret == -512) > > DVB: TDA10023: tda10023_readreg: readreg error (ret == -512) > > > > and it doesn't find any channels as it should. I have a set top box > > from my cable provider which works fine with this tuning frequencie. > > > > I'm running debian unstable with a 2.6.24.2 kernel. > > Here is the initialization of the card : > > > > PCI: Found IRQ 10 for device 0000:00:0e.0 > > saa7146: found saa7146 @ mem f88d2000 (revision 1, irq 10) (0x1894,0x002c). > > saa7146 (0): dma buffer size 192512 > > DVB: registering new adapter (Satelco EasyWatch DVB-C MK3) > > adapter failed MAC signature check > > encoded MAC from EEPROM was > > ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff > > via-rhine.c:v1.10-LK1.4.3 2007-03-06 Written by Donald Becker > > KNC1-0: MAC addr = 00:09:d6:6d:a5:0b > > DVB: registering frontend 0 (Philips TDA10023 DVB-C)... > > budget-av: ci interface initialised. > > > > and the result of lsmod : > > lsmod > > Module Size Used by > > nfs 116076 1 > > lockd 59784 1 nfs > > sunrpc 155164 8 nfs,lockd > > fglrx 1479212 18 > > sr_mod 14116 0 > > sd_mod 20880 0 > > 8250 19700 0 > > serial_core 16640 1 8250 > > tda10023 5764 1 > > via_rhine 19464 0 > > mii 4480 1 via_rhine > > budget_av 17792 0 > > saa7146_vv 44288 1 budget_av > > videobuf_dma_sg 11012 1 saa7146_vv > > videobuf_core 14340 2 saa7146_vv,videobuf_dma_sg > > budget_core 8452 1 budget_av > > dvb_core 70396 2 budget_av,budget_core > > saa7146 14984 3 budget_av,saa7146_vv,budget_core > > ttpci_eeprom 2176 1 budget_core > > via_agp 8064 1 > > agpgart 26288 2 fglrx,via_agp > > evdev 8576 1 > > > > what's wrong ? where is my error ? > > thanks a lot for your help > > > > Guillaume > > > _______________________________________________ linux-dvb mailing list linux-dvb@linuxtv.org http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb