Good morning to everyone, I tested the Stick with windows and it found channels ok.. So what shall I do next?
-antti- 2008/3/18, Antti Luoma <[EMAIL PROTECTED]>: > > Hi, > > Tested with same results :( (no channels...) > > Tomorrow I'l (hmm today, its getting late) test this with windows that it > works in there... > > -Antti- > > > 2008/3/18, Albert Comerma <[EMAIL PROTECTED]>: > > > > Just as I pointed a few hours ago; > > > > If you speak french you can have a look here; > > > > http://www.louviaux.com-a.googlepages.com/tntpinnaclepctvdvb-t72e > > > > Or if you don't you can go the fast way; > > > > wget http://www.barbak.org/v4l_for_72e_dongle.tar.bz2 > > tar xvjf v4l_for_72e_dongle.tar.bz2 > > cd v4l-dvb > > sudo cp firmware/dvb-usb-dib0700-1.10.fw /lib/firmware/ > > make all > > sudo make install > > > > That should work for you. Please let me know. > > > > 2008/3/17, Antti Luoma <[EMAIL PROTECTED]>: > > > > > > Hi, > > > > > > I have trying to get Solo Stick (72e) to work for couple of days, but > > > with no luck. So what's the current status of this driver? > > > > > > I did download latest drivers from mercurial today, added PCI_ids for > > > card, modified dib0700_devices.c (in stk7070p_frontend_attach), added > > > device > > > to struct dvb_usb_device_properties dib0700_devices[] where > > > stk7070p_frontend_attach was called. > > > > > > After that it looked promising: > > > > > > usb 6-4: new high speed USB device using ehci_hcd and address 30 > > > [ 6722.607546] usb 6-4: configuration #1 chosen from 1 choice > > > [ 6722.607622] dvb-usb: found a 'Pinnacle PCTV 72e DVB-T' in warm > > > state. > > > [ 6722.607648] dvb-usb: will pass the complete MPEG2 transport stream > > > to the software demuxer. > > > [ 6722.607724] DVB: registering new adapter (Pinnacle PCTV 72e DVB-T) > > > [ 6722.731734] dvb_register_frontend > > > [ 6722.731742] DVB: registering frontend 0 (DiBcom 7000PC)... > > > [ 6722.811550] DiB0070: successfully identified > > > [ 6722.811557] dvb-usb: Pinnacle PCTV 72e DVB-T successfully > > > initialized and connected. > > > > > > > > > BUT if I do a scan I don't get channels (i checked that I have correct > > > frequencies): > > > > > > #scan -o vdr fi-Eurajoki > > > scanning fi-Eurajoki > > > using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0' > > > initial transponder 610000000 0 2 9 3 1 2 0 > > > initial transponder 666000000 0 2 9 3 1 2 0 > > > initial transponder 722000000 0 2 9 3 1 2 0 > > > >>> tune to: 610000:I999B8C23D999M64T8G8Y0:T:27500: > > > WARNING: filter timeout pid 0x0011 > > > WARNING: filter timeout pid 0x0000 > > > WARNING: filter timeout pid 0x0010 > > > >>> tune to: 666000:I999B8C23D999M64T8G8Y0:T:27500: > > > __tune_to_transponder:1483: ERROR: Setting frontend parameters failed: > > > 19 No such device > > > >>> tune to: 666000:I999B8C23D999M64T8G8Y0:T:27500: > > > __tune_to_transponder:1483: ERROR: Setting frontend parameters failed: > > > 19 No such device > > > >>> tune to: 722000:I999B8C23D999M64T8G8Y0:T:27500: > > > __tune_to_transponder:1483: ERROR: Setting frontend parameters failed: > > > 19 No such device > > > >>> tune to: 722000:I999B8C23D999M64T8G8Y0:T:27500: > > > __tune_to_transponder:1483: ERROR: Setting frontend parameters failed: > > > 19 No such device > > > dumping lists (0 services) > > > Done. > > > > > > Any thoughts?? > > > > > > -- > > > -Antti- > > > _______________________________________________ > > > linux-dvb mailing list > > > linux-dvb@linuxtv.org > > > http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb > > > > > > > > > > -- > -Antti- -- -Antti-
_______________________________________________ linux-dvb mailing list linux-dvb@linuxtv.org http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
