On Fri, May 22, 2015 at 03:14:28PM -0700, Ellen Wang wrote: > On a CRC error while using hardware-supported PEC, an additional > error bit is set in the auxiliary status register. If this bit > isn't cleared, all subsequent operations will fail, essentially > hanging the controller. > > The fix is simple: check, report, and clear the bit in > i801_check_post(). Also, in case the driver starts with the > hardware in that state, clear it in i801_check_pre() as well. > > Signed-off-by: Ellen Wang <[email protected]> > --- > Update: fix typos in commit message, otherwise the same as v2 > > This is essentially the patch from Jean Delvare, which handles > the polling case while my original version didn't. (Thank you! > Please add appropriate attribution if you wish.) > > I tested all the additional code paths by selectively commenting > out code: with interrupts, without interrupts, relying on check_pre() > to clear CRCE, no clearing of CRCE at all (baseline).
Jean, any comments or tags to add?
> ---
> drivers/i2c/busses/i2c-i801.c | 53
> +++++++++++++++++++++++++++++++++++++++--
> 1 file changed, 51 insertions(+), 2 deletions(-)
>
> diff --git a/drivers/i2c/busses/i2c-i801.c b/drivers/i2c/busses/i2c-i801.c
> index 5ecbb3f..fa50df0 100644
> --- a/drivers/i2c/busses/i2c-i801.c
> +++ b/drivers/i2c/busses/i2c-i801.c
> @@ -125,6 +125,10 @@
> #define SMBHSTCFG_SMB_SMI_EN 2
> #define SMBHSTCFG_I2C_EN 4
>
> +/* Auxiliary status register bits, ICH4+ only */
> +#define SMBAUXSTS_CRCE 1
> +#define SMBAUXSTS_STCO 2
> +
> /* Auxiliary control register bits, ICH4+ only */
> #define SMBAUXCTL_CRC 1
> #define SMBAUXCTL_E32B 2
> @@ -273,6 +277,29 @@ static int i801_check_pre(struct i801_priv *priv)
> }
> }
>
> + /*
> + * Clear CRC status if needed.
> + * During normal operation, i801_check_post() takes care
> + * of it after every operation. We do it here only in case
> + * the hardware was already in this state when the driver
> + * started.
> + */
> + if (priv->features & FEATURE_SMBUS_PEC) {
> + status = inb_p(SMBAUXSTS(priv)) & SMBAUXSTS_CRCE;
> + if (status) {
> + dev_dbg(&priv->pci_dev->dev,
> + "Clearing aux status flags (%02x)\n", status);
> + outb_p(status, SMBAUXSTS(priv));
> + status = inb_p(SMBAUXSTS(priv)) & SMBAUXSTS_CRCE;
> + if (status) {
> + dev_err(&priv->pci_dev->dev,
> + "Failed clearing aux status flags
> (%02x)\n",
> + status);
> + return -EBUSY;
> + }
> + }
> + }
> +
> return 0;
> }
>
> @@ -316,8 +343,30 @@ static int i801_check_post(struct i801_priv *priv, int
> status)
> dev_err(&priv->pci_dev->dev, "Transaction failed\n");
> }
> if (status & SMBHSTSTS_DEV_ERR) {
> - result = -ENXIO;
> - dev_dbg(&priv->pci_dev->dev, "No response\n");
> + /*
> + * This may be a PEC error, check and clear it.
> + *
> + * AUXSTS is handled differently from HSTSTS.
> + * For HSTSTS, i801_isr() or i801_wait_intr()
> + * has already cleared the error bits in hardware,
> + * and we are passed a copy of the original value
> + * in "status".
> + * For AUXSTS, the hardware register is left
> + * for us to handle here.
> + * This is asymmetric, slightly iffy, but safe,
> + * since all this code is serialized and the CRCE
> + * bit is harmless as long as it's cleared before
> + * the next operation.
> + */
> + if ((priv->features & FEATURE_SMBUS_PEC) &&
> + (inb_p(SMBAUXSTS(priv)) & SMBAUXSTS_CRCE)) {
> + outb_p(SMBAUXSTS_CRCE, SMBAUXSTS(priv));
> + result = -EBADMSG;
> + dev_dbg(&priv->pci_dev->dev, "PEC error\n");
> + } else {
> + result = -ENXIO;
> + dev_dbg(&priv->pci_dev->dev, "No response\n");
> + }
> }
> if (status & SMBHSTSTS_BUS_ERR) {
> result = -EAGAIN;
> --
> 1.7.10.4
>
signature.asc
Description: Digital signature
