Am 25.08.2015 um 13:09 schrieb Gao Pandy:
> From: Heiner Kallweit <mailto:hkallwe...@gmail.com> Sent: Tuesday, August 25,
> 2015 2:37 PM
>> To: Gao Pan-B54642; w...@the-dreams.de
>> Cc: linux-i2c@vger.kernel.org; Li Frank-B20596; Duan Fugang-B38611;
>> u.kleine-koe...@pengutronix.de; ker...@pengutronix.de
>> Subject: Re: [Patch V4] i2c: imx: add runtime pm support to improve the
>> performance
>>
>> Am 25.08.2015 um 04:20 schrieb Gao Pan:
>>> In our former i2c driver, i2c clk is enabled and disabled in xfer
>>> function, which contributes to power saving. However, the clk enable
>>> process brings a busy wait delay until the core is stable. As a
>>> result, the performance is sacrificed.
>>>
>>> To weigh the power consumption and i2c bus performance, runtime pm is
>>> the good solution for it. The clk is enabled when a i2c transfer
>>> starts, and disabled after a specifically defined delay.
>>>
>>> Without the patch the test case (many eeprom reads) executes with
>> approx:
>>> real 1m7.735s
>>> user 0m0.488s
>>> sys 0m20.040s
>>>
>>> With the patch the same test case (many eeprom reads) executes with
>> approx:
>>> real 0m54.241s
>>> user 0m0.440s
>>> sys 0m5.920s
>>>
>>> Signed-off-by: Fugang Duan <b38...@freescale.com>
>>> Signed-off-by: Gao Pan <b54...@freescale.com>
>>> [wsa: fixed some indentation]
>>> Signed-off-by: Wolfram Sang <w...@the-dreams.de>
>>> ---
>>> V2:
>>> As Uwe Kleine-König's suggestion, the version do below changes:
>>> -call clk_prepare_enable in probe to avoid never enabling clock
>>> if CONFIG_PM is disabled
>>> -enable clock before request IRQ in probe -remove the pm staff in
>>> i2c_imx_isr
>>>
>>> V3:
>>> -pm_runtime_get_sync returns < 0 as error
>>>
>>> V4:
>>> -add pm_runtime_set_active before pm_runtime_enable -replace
>>> pm_runtime_put_autosuspend with pm_runtime_autosuspend
>>> in probe
>>> -add error disposal when i2c_add_numbered_adapter fails
>>>
>>> drivers/i2c/busses/i2c-imx.c | 79
>>> ++++++++++++++++++++++++++++++++++++++------
>>> 1 file changed, 68 insertions(+), 11 deletions(-)
>>>
>>> diff --git a/drivers/i2c/busses/i2c-imx.c
>>> b/drivers/i2c/busses/i2c-imx.c index 785aa67..7c63047 100644
>>> --- a/drivers/i2c/busses/i2c-imx.c
>>> +++ b/drivers/i2c/busses/i2c-imx.c
>>> @@ -53,6 +53,7 @@
>>> #include <linux/platform_device.h>
>>> #include <linux/sched.h>
>>> #include <linux/slab.h>
>>> +#include <linux/pm_runtime.h>
>>>
>>> /** Defines
>>> ********************************************************************
>>>
>>> **********************************************************************
>>> *********/
>>> @@ -118,6 +119,8 @@
>>> #define I2CR_IEN_OPCODE_0 0x0
>>> #define I2CR_IEN_OPCODE_1 I2CR_IEN
>>>
>>> +#define I2C_PM_TIMEOUT 10 /* ms */
>>> +
>>> /** Variables
>>> ******************************************************************
>>>
>>> **********************************************************************
>>> *********/
>>>
>>> @@ -520,9 +523,6 @@ static int i2c_imx_start(struct imx_i2c_struct
>>> *i2c_imx)
>>>
>>> i2c_imx_set_clk(i2c_imx);
>>>
>>> - result = clk_prepare_enable(i2c_imx->clk);
>>> - if (result)
>>> - return result;
>>> imx_i2c_write_reg(i2c_imx->ifdr, i2c_imx, IMX_I2C_IFDR);
>>> /* Enable I2C controller */
>>> imx_i2c_write_reg(i2c_imx->hwdata->i2sr_clr_opcode, i2c_imx,
>>> IMX_I2C_I2SR); @@ -575,7 +575,6 @@ static void i2c_imx_stop(struct
>> imx_i2c_struct *i2c_imx)
>>> /* Disable I2C controller */
>>> temp = i2c_imx->hwdata->i2cr_ien_opcode ^ I2CR_IEN,
>>> imx_i2c_write_reg(temp, i2c_imx, IMX_I2C_I2CR);
>>> - clk_disable_unprepare(i2c_imx->clk);
>>> }
>>>
>>> static irqreturn_t i2c_imx_isr(int irq, void *dev_id) @@ -894,6
>>> +893,10 @@ static int i2c_imx_xfer(struct i2c_adapter *adapter,
>>>
>>> dev_dbg(&i2c_imx->adapter.dev, "<%s>\n", __func__);
>>>
>>> + result = pm_runtime_get_sync(i2c_imx->adapter.dev.parent);
>>> + if (result < 0)
>>> + goto out;
>>> +
>>> /* Start I2C transfer */
>>> result = i2c_imx_start(i2c_imx);
>>> if (result)
>>> @@ -950,6 +953,10 @@ fail0:
>>> /* Stop I2C transfer */
>>> i2c_imx_stop(i2c_imx);
>>>
>>> +out:
>>> + pm_runtime_mark_last_busy(i2c_imx->adapter.dev.parent);
>>> + pm_runtime_put_autosuspend(i2c_imx->adapter.dev.parent);
>>> +
>>> dev_dbg(&i2c_imx->adapter.dev, "<%s> exit with: %s: %d\n", __func__,
>>> (result < 0) ? "error" : "success msg",
>>> (result < 0) ? result : num);
>>> @@ -1020,9 +1027,10 @@ static int i2c_imx_probe(struct platform_device
>>> *pdev)
>>>
>>> ret = clk_prepare_enable(i2c_imx->clk);
>>> if (ret) {
>>> - dev_err(&pdev->dev, "can't enable I2C clock\n");
>>> + dev_err(&pdev->dev, "can't enable I2C clock, ret=%d\n", ret);
>>> return ret;
>>> }
>>> +
>>> /* Request IRQ */
>>> ret = devm_request_irq(&pdev->dev, irq, i2c_imx_isr, 0,
>>> pdev->name, i2c_imx);
>>> @@ -1037,6 +1045,14 @@ static int i2c_imx_probe(struct platform_device
>> *pdev)
>>> /* Set up adapter data */
>>> i2c_set_adapdata(&i2c_imx->adapter, i2c_imx);
>>>
>>> + /* Set up platform driver data */
>>> + platform_set_drvdata(pdev, i2c_imx);
>>> +
>>> + pm_runtime_set_autosuspend_delay(&pdev->dev, I2C_PM_TIMEOUT);
>>> + pm_runtime_use_autosuspend(&pdev->dev);
>>> + pm_runtime_set_active(&pdev->dev);
>>> + pm_runtime_enable(&pdev->dev);
>>> +
>>> /* Set up clock divider */
>>> i2c_imx->bitrate = IMX_I2C_BIT_RATE;
>>> ret = of_property_read_u32(pdev->dev.of_node,
>>> @@ -1053,12 +1069,13 @@ static int i2c_imx_probe(struct platform_device
>> *pdev)
>>> ret = i2c_add_numbered_adapter(&i2c_imx->adapter);
>>> if (ret < 0) {
>>> dev_err(&pdev->dev, "registration failed\n");
>>> + pm_runtime_mark_last_busy(&pdev->dev);
>>> + pm_runtime_autosuspend(&pdev->dev);
>> It would be more consistent with the general practice not to clean up
>> here but to define a new error label, goto there and do the clean-up
>> there.
>> And if adding the adapter fails most likely you don't want to autosuspend
>> but clean up and disable runtime PM.
>
> Thank you, will change it in next version.
>
>>> goto clk_disable;
>>> }
>>>
>>> - /* Set up platform driver data */
>>> - platform_set_drvdata(pdev, i2c_imx);
>>> - clk_disable_unprepare(i2c_imx->clk);
>>> + pm_runtime_mark_last_busy(&pdev->dev);
>>> + pm_runtime_autosuspend(&pdev->dev);
>> >From enabling runtime PM to here you don't hold a reference so
>>> theoretically
>> it might happen that the device gets suspended in-between.
>> I'm not able to say whether this is an actual potential issue here.
>> However to be on the safe side it wouldn't hurt to do a pm_runtime_get_xx
>> when enabling PM and use pm_runtime_put_autosuspend here.
>
> Thanks. If I use pm_runtime_get_xx when enabling PM, clk_prepare_enable will
> be called again.
> However, it has been called before. It's kind of code redundancy to use
> pm_runtime_get_xx.
No, it won't. This function checks whether the device is in state "active" and
in this case
it doesn't call the resume callback and returns 1.
See also the source code of runtime PM in drivers/base/power/runtime.c
Rgds, Heiner
>
>> Regards, Heiner
>>>
>>> dev_dbg(&i2c_imx->adapter.dev, "claimed irq %d\n", irq);
>>> dev_dbg(&i2c_imx->adapter.dev, "device resources: %pR\n", res); @@
>>> -1079,6 +1096,11 @@ clk_disable:
>>> static int i2c_imx_remove(struct platform_device *pdev) {
>>> struct imx_i2c_struct *i2c_imx = platform_get_drvdata(pdev);
>>> + int ret;
>>> +
>>> + ret = pm_runtime_get_sync(&pdev->dev);
>>> + if (ret < 0)
>>> + return ret;
>>>
>>> /* remove adapter */
>>> dev_dbg(&i2c_imx->adapter.dev, "adapter removed\n"); @@ -1093,17
>>> +1115,52 @@ static int i2c_imx_remove(struct platform_device *pdev)
>>> imx_i2c_write_reg(0, i2c_imx, IMX_I2C_I2CR);
>>> imx_i2c_write_reg(0, i2c_imx, IMX_I2C_I2SR);
>>>
>>> + pm_runtime_put_sync(&pdev->dev);
>>> + pm_runtime_disable(&pdev->dev);
>>> +
>>> return 0;
>>> }
>>>
>>> +#ifdef CONFIG_PM
>>> +static int i2c_imx_runtime_suspend(struct device *dev) {
>>> + struct imx_i2c_struct *i2c_imx = dev_get_drvdata(dev);
>>> +
>>> + clk_disable_unprepare(i2c_imx->clk);
>>> +
>>> + return 0;
>>> +}
>>> +
>>> +static int i2c_imx_runtime_resume(struct device *dev) {
>>> + struct imx_i2c_struct *i2c_imx = dev_get_drvdata(dev);
>>> + int ret;
>>> +
>>> + ret = clk_prepare_enable(i2c_imx->clk);
>>> + if (ret)
>>> + dev_err(dev, "can't enable I2C clock, ret=%d\n", ret);
>>> +
>>> + return ret;
>>> +}
>>> +
>>> +static const struct dev_pm_ops i2c_imx_pm_ops = {
>>> + SET_RUNTIME_PM_OPS(i2c_imx_runtime_suspend,
>>> + i2c_imx_runtime_resume, NULL)
>>> +};
>>> +#define I2C_IMX_PM_OPS (&i2c_imx_pm_ops) #else #define I2C_IMX_PM_OPS
>>> +NULL #endif /* CONFIG_PM */
>>> +
>>> static struct platform_driver i2c_imx_driver = {
>>> .probe = i2c_imx_probe,
>>> .remove = i2c_imx_remove,
>>> - .driver = {
>>> - .name = DRIVER_NAME,
>>> + .driver = {
>>> + .name = DRIVER_NAME,
>>> + .pm = I2C_IMX_PM_OPS,
>>> .of_match_table = i2c_imx_dt_ids,
>>> },
>>> - .id_table = imx_i2c_devtype,
>>> + .id_table = imx_i2c_devtype,
>>> };
>>>
>>> static int __init i2c_adap_imx_init(void)
>>>
>
--
To unsubscribe from this list: send the line "unsubscribe linux-i2c" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
