Bartlomiej Zolnierkiewicz wrote:
Sergei, do we need to disallow UDMA6 completely on HPT734 or
is it only an issue with some problematic devices (=> blacklist)?
Note that I didn't change what the old code was doing in this regard --
although the HPT374 spec does *not* say that UDMA6 is supported, it had been
enabled. What have *really* changed for HPT374 was:
- in 2.6.20-rc1, the driver switched to using the actual 33 MHz timing table
instead of the old one, matching 50 MHz (and so, severely underclocked);
- in 2.6.2-rc1, the driver switched from 33 MHz PCI to 66 MHz DPLL clock.
Disallowing UDMA6 would clock the chip with 50 MHz DPLL, howewer, the
I felt inspired by this explanation (thanks!) and took a look at
hpt374-opensource-v2.10 vendor driver. Here is something interesting:
glbdata.c:
...
#ifdef CLOCK_66MHZ
ULONG setting370_66[] = {
0xd029d5e, 0xd029d26, 0xc829ca6, 0xc829c84, 0xc829c62,
0x2c829d2c, 0x2c829c66, 0x2c829c62,
0x1c829c62, 0x1c9a9c62, 0x1c929c62, 0x1c8e9c62, 0x1c8a9c62,
0x1c8a9c62/*0x1cae9c62*/, 0x1c869c62, 0x1c869c62,
};
...
hpt366.c:
...
static u32 sixty_six_base_hpt37x[] = {
/* XFER_UDMA_6 */ 0x1c869c62,
/* XFER_UDMA_5 */ 0x1cae9c62, /* 0x1c8a9c62 */
...
So we are using Dual ATA Clock for UDMA5 whereas vendor driver doesn't
This is so in all other HPT drivers (and HPT371N datasheet has the same
figures -- this chip is the only one supporting UDMA6 and having the default
DPLL clock > 50 MHz). Note that it means that there's no actual UDMA5 since
the timing exactly matches that one used for UDMA4.
(the only other mode which uses Dual ATA Clock, in both drivers, is rarely
used UDMA3).
And UDMA4 with 50 MHz clock.
Thanks to this UDMA cycle time should be equal 22.5ns instead of 30ns
(spec defines it at 16.8ns, ide_timings[] uses 20ns) when using 66 MHz DPLL
clock. In theory everything should play nice but the data manual for HPT374
And it does -- on other chips.
My beautiful theory failed... Oh, well... ;)
Sigh, if we only knew why HPT decided that UDMA5 timings should be the
same as UDMA4 -- probably they had some reason...
contains weird note that Dual ATA Clock is meant to implement ATA100 read
and write at different clocks (there is no more explanation to this).
That's the thing that keeps me confused in the other datasheets too --
from my interpretation of their timing figures it seemed to control 2x ATA
clock multipler. HPT370 datasheet just gives different timings and SCR2 values
for reads/writes in UDMA5 (I've disabled this mode on HPT370 from which the
read performance only gained -- not sure if it makes sense to restore the old
clock turnaround hack).
It used to clock the writes from DPLL in UDMA5, and clock UDMA5 reads and
all other modes from PCI... And the result was dog slow reads in UDMA5 which
UDMA4 was beating by about 8 MB/s... Maybe that's why UDMA4 timings were used
for UDMA5 in later chips by HPT -- but the real UDMA5 yielded faster transfer
speeds than UDMA4 for those chips...
Geller reported that the problems started after migrating from 2.6.20.7 to
2.6.21.1 (the affected disks are using UDMA5) and at the same time the driver
switched from 33 MHz PCI to 66 MHz DPLL clock. Also the issue is completely
fixed by using 50 MHz DPLL clock (UDMA5 timing for 50 MHz DPLL clock is
0x12848242 so UDMA cycle time equals 20ns and is smaller than the one
obtained using 66 MHz DPLL clock).
It all makes me wonder whether it is really safe to use Dual ATA Clock for
UDMA5 and whether we should just be using "the offical" timing instead...
Not sure. I had no problems with this on the HPT371N/302 and 371N was
clocked by 66 MHz DPLL from the start (its default clock is 75 MHz however).
I meant to say 77... :-)
I'm still holding to my hypothesis that HPT374 simply can't tolerate 66
MHz DPLL clock, and the UDMA5 timing figures that you've cited seem to prove that.
I'm going to post a patch today -- how about completely prohibiting UDMA6
on HPT374?
Sounds fine, in case somebody misses it we can introduce something like
hpt374_allow_66mhz_dpll module parameter...
Don't think anybody will miss it. Anyway, chip spec doesn't say that it's
supported.
Thanks,
Bart
MBR, Sergei
-
To unsubscribe from this list: send the line "unsubscribe linux-ide" in
the body of a message to [EMAIL PROTECTED]
More majordomo info at http://vger.kernel.org/majordomo-info.html