On 10/18/07, Tejun Heo <[EMAIL PROTECTED]> wrote: > Hello, all. > > Torsten, Clarence is reporting similar problem on 2.6.22. The original > message follows.
I don't think it matches. > > I'm using the 2.6.22 sources with a Sii3132 SATA controller and a Seagate > > HDD. > > What I've noticed is that it often fails to boot with this configuration. > > Warm boots appear to always fail while cold boots (power-cycles) fail maybe > > 20%-50% of the time. Here's a log from my last attempt: For me warm boots always worked and even cold boots only failed after turning the power off for several minutes. (I tested with ~1 hour downtime) But the failures on cold boot where "relativ" reliable, I would guess >50%. > > Loading iSCSI transport class v2.0-724. > > PCI: Enabling device 0000:01:00.0 (0000 -> 0003) > > scsi0 : sata_sil24 > > scsi1 : sata_sil24 > > ata1: SATA max UDMA/100 cmd 0xe1258000 ctl 0x00000000 bmdma 0x00000000 irq 0 > > ata2: SATA max UDMA/100 cmd 0xe125a000 ctl 0x00000000 bmdma 0x00000000 irq 0 > > ata1: SATA link down (SStatus 0 SControl 0) > > ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 0) > > ata2.00: qc timeout (cmd 0xec) > > ata2.00: failed to IDENTIFY (I/O error, err_mask=0x4) > > ata2: failed to recover some devices, retrying in 5 secs > > ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 0) > > ata2.00: qc timeout (cmd 0xec) > > ata2.00: failed to IDENTIFY (I/O error, err_mask=0x4) > > ata2: limiting SATA link speed to 1.5 Gbps > > ata2.00: limiting speed to UDMA7:PIO5 My failure also came much later. It seemed the first write command (to a md raid) triggered it. All of my drives where always detected correctly. > > ata2: failed to recover some devices, retrying in 5 secs > > ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 10) > > ata2.00: qc timeout (cmd 0xec) > > ata2.00: failed to IDENTIFY (I/O error, err_mask=0x4) > > ata2: failed to recover some devices, retrying in 5 secs > > ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 10) > > ata2: EH pending after completion, repeating EH (cnt=4) > > i2c /dev entries driver > > IBM IIC driver v2.1 > > > > If the boot succeeds, I have no further problems with HDD access. > > I also did not see this problem with the 2.6.17 kernel. Do you have > > any ideas as to what may be happening? We're running on a PPC440SPE > > processor. I'm using x86_64 on an Opteron system. > The symptom seems very similar to yours but the kernel is 2.6.22 which > doesn't have the SG change which you found out to be broken. Can you > update us on how the testing of patched kernel went? Sorry I didn't realize that you where still waiting for a 'confirm good'. I intended only to mail, if I got the error again, as the debug output about SGE_TRM confirmed, that this fix changes the behavior of sata_sil24 and there was no really 200% sure method of detecting that this bug was gone. Anyway, after fixing ata_sg_is_last() by adding the +1 I did not had a single failure. I'm currently using 2.6.23-mm1 and 16 boots where all good. (Apart from the unrelated failure with sata_nv and swncq...) Torsten - To unsubscribe from this list: send the line "unsubscribe linux-ide" in the body of a message to [EMAIL PROTECTED] More majordomo info at http://vger.kernel.org/majordomo-info.html