* Set the correct hwif->dma_base for the second channel in
ide_get_or_set_dma_base().
* Remove DMA enable code from cs5520_set_pio_mode(), this can
be handled by the generic ->dma_host_on method now.
* Add VDMA check to ide_config_drive_speed().
* drive->using_dma was never enabled since cs5520 host driver's
->ide_dma_on method overrided the generic ->ide_dma_on (so
__ide_dma_on() was never called, drive->using_dma was never set
and VDMA was never used since it depends on drive->using_dma).
Fix it by using ->dma_host_on method instead of ->ide_dma_on
(also add matching ->dma_host_off method).
Signed-off-by: Bartlomiej Zolnierkiewicz <[EMAIL PROTECTED]>
---
drivers/ide/ide-iops.c | 2 +-
drivers/ide/pci/cs5520.c | 29 +++++++++++++++++------------
drivers/ide/setup-pci.c | 10 +++++++---
3 files changed, 25 insertions(+), 16 deletions(-)
Index: b/drivers/ide/ide-iops.c
===================================================================
--- a/drivers/ide/ide-iops.c
+++ b/drivers/ide/ide-iops.c
@@ -791,7 +791,7 @@ int ide_config_drive_speed(ide_drive_t *
drive->id->dma_1word &= ~0x0F00;
#ifdef CONFIG_BLK_DEV_IDEDMA
- if (speed >= XFER_SW_DMA_0)
+ if (speed >= XFER_SW_DMA_0 || (hwif->host_flags & IDE_HFLAG_VDMA))
hwif->dma_host_on(drive);
else if (hwif->ide_dma_on) /* check if host supports DMA */
hwif->dma_off_quietly(drive);
Index: b/drivers/ide/pci/cs5520.c
===================================================================
--- a/drivers/ide/pci/cs5520.c
+++ b/drivers/ide/pci/cs5520.c
@@ -71,7 +71,6 @@ static void cs5520_set_pio_mode(ide_driv
ide_hwif_t *hwif = HWIF(drive);
struct pci_dev *pdev = hwif->pci_dev;
int controller = drive->dn > 1 ? 1 : 0;
- u8 reg;
/* FIXME: if DMA = 1 do we need to set the DMA bit here ? */
@@ -91,11 +90,6 @@ static void cs5520_set_pio_mode(ide_driv
pci_write_config_byte(pdev, 0x66 + 4*controller + (drive->dn&1),
(cs5520_pio_clocks[pio].recovery << 4) |
(cs5520_pio_clocks[pio].assert));
-
- /* Set the DMA enable/disable flag */
- reg = inb(hwif->dma_base + 0x02 + 8*controller);
- reg |= 1<<((drive->dn&1)+5);
- outb(reg, hwif->dma_base + 0x02 + 8*controller);
}
static void cs5520_set_dma_mode(ide_drive_t *drive, const u8 speed)
@@ -109,13 +103,23 @@ static void cs5520_set_dma_mode(ide_driv
* We wrap the DMA activate to set the vdma flag. This is needed
* so that the IDE DMA layer issues PIO not DMA commands over the
* DMA channel
+ *
+ * ATAPI is harder so disable it for now using IDE_HFLAG_NO_ATAPI_DMA
*/
-
-static int cs5520_dma_on(ide_drive_t *drive)
+
+static void cs5520_dma_host_on(ide_drive_t *drive)
{
- /* ATAPI is harder so leave it for now */
- drive->vdma = 1;
- return 0;
+ if (drive->using_dma)
+ drive->vdma = 1;
+
+ ide_dma_host_on(drive);
+}
+
+static void cs5520_dma_host_off(ide_drive_t *drive)
+{
+ drive->vdma = 0;
+
+ ide_dma_host_off(drive);
}
static void __devinit init_hwif_cs5520(ide_hwif_t *hwif)
@@ -126,7 +130,8 @@ static void __devinit init_hwif_cs5520(i
if (hwif->dma_base == 0)
return;
- hwif->ide_dma_on = &cs5520_dma_on;
+ hwif->dma_host_on = &cs5520_dma_host_on;
+ hwif->dma_host_off = &cs5520_dma_host_off;
}
#define DECLARE_CS_DEV(name_str) \
Index: b/drivers/ide/setup-pci.c
===================================================================
--- a/drivers/ide/setup-pci.c
+++ b/drivers/ide/setup-pci.c
@@ -170,13 +170,17 @@ static unsigned long ide_get_or_set_dma_
dma_base = pci_resource_start(dev, baridx);
- if (dma_base == 0)
+ if (dma_base == 0) {
printk(KERN_ERR "%s: DMA base is invalid\n", d->name);
+ return 0;
+ }
}
- if ((d->host_flags & IDE_HFLAG_CS5520) == 0 && dma_base) {
+ if (hwif->channel)
+ dma_base += 8;
+
+ if ((d->host_flags & IDE_HFLAG_CS5520) == 0) {
u8 simplex_stat = 0;
- dma_base += hwif->channel ? 8 : 0;
switch(dev->device) {
case PCI_DEVICE_ID_AL_M5219:
-
To unsubscribe from this list: send the line "unsubscribe linux-ide" in
the body of a message to [EMAIL PROTECTED]
More majordomo info at http://vger.kernel.org/majordomo-info.html
