>-----Original Message-----
>From: Gaston, Jason D
>Sent: Tuesday, January 08, 2008 4:21 PM
>To: 'Tejun Heo'; Tom Evans
>Cc: linux-ide@vger.kernel.org
>Subject: RE: SATA PMP support in 2.6.24-rc3?
>
>>-----Original Message-----
>>From: Tejun Heo [mailto:[EMAIL PROTECTED]
>>Sent: Tuesday, January 08, 2008 4:28 AM
>>To: Tom Evans
>>Cc: Gaston, Jason D; linux-ide@vger.kernel.org
>>Subject: Re: SATA PMP support in 2.6.24-rc3?
>>
>>Tom Evans wrote:
>>>
>>> I'm also seeing this with 2.6.23-rc3 on my Alpha system - sata_sil24
and
>>> a SiliconImage PMP.
>>
>>Gaston, Tom, can you guys please apply the attached patch on top of
>>2.6.24-rc7 and see whether the problem goes away.
>>
>>Thanks.
>>
>>--
>>Tejun
>
>I moved to another ICH9 system that has support for PMP in the BIOS.
>Before and after the patch, I am able to use the PMP, but I still get
>errors. I have attached the dmesg output w/ patch to this email. In
this
>case, I booted the system with the PMP turned off and then switched it
on
>after the system was up and running, so you will see the PMP messages
at
>the bottom.
>
>On the old system, I get the error messages, but still never see the
drives
>in /sys/block/
>
>Thanks,
>
>Jason
For reference, here is the dmesg output from the 2.6.24-rc7 kernel W/O
the patch applied.
Thanks,
Jason
Linux version 2.6.24-rc7_WOpatch ([EMAIL PROTECTED]) (gcc version 4.1.2
20070626 (Red Hat 4.1.2-14)) #1 SMP Tue Jan 8 17:58:25 PST 2008
Command line: ro root=/dev/VolGroup00/LogVol00 pci=nommconf rhgb quiet
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009d000 (usable)
BIOS-e820: 000000000009d000 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003e7dd000 (usable)
BIOS-e820: 000000003e7dd000 - 000000003e81e000 (ACPI NVS)
BIOS-e820: 000000003e81e000 - 000000003e822000 (reserved)
BIOS-e820: 000000003e822000 - 000000003e879000 (ACPI NVS)
BIOS-e820: 000000003e879000 - 000000003ea28000 (reserved)
BIOS-e820: 000000003ea28000 - 000000003ea3c000 (ACPI NVS)
BIOS-e820: 000000003ea3c000 - 000000003efde000 (reserved)
BIOS-e820: 000000003efde000 - 000000003efed000 (ACPI NVS)
BIOS-e820: 000000003efed000 - 000000003f0d2000 (reserved)
BIOS-e820: 000000003f0d2000 - 000000003f114000 (ACPI data)
BIOS-e820: 000000003f114000 - 000000003f134000 (ACPI NVS)
BIOS-e820: 000000003f134000 - 000000003f136000 (reserved)
BIOS-e820: 000000003f136000 - 000000003f138000 (ACPI NVS)
BIOS-e820: 000000003f138000 - 000000003f4d0000 (reserved)
BIOS-e820: 000000003f4d0000 - 000000003f500000 (ACPI NVS)
BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
BIOS-e820: 00000000fed1c000 - 00000000fed20000 (reserved)
BIOS-e820: 00000000ffa80000 - 00000000ffc00000 (reserved)
BIOS-e820: 00000000ffe80000 - 0000000100000000 (reserved)
Entering add_active_range(0, 0, 157) 0 entries of 3200 used
Entering add_active_range(0, 256, 255965) 1 entries of 3200 used
end_pfn_map = 1048576
DMI 2.4 present.
ACPI: RSDP 000F03C0, 0024 (r2 AMI)
ACPI: XSDT 3F0D6E18, 004C (r1 AMI PILLARRK 6222004 MSFT 10013)
ACPI: FACP 3EFE0918, 00F4 (r4 AMI PILLARRK 6222004 MSFT 10013)
ACPI: DSDT 3EA28018, 98BA (r1 AMI PILLARRK 0 INTL 20060912)
ACPI: FACS 3F136E40, 0040
ACPI: APIC 3F0D2F18, 006C (r2 AMI PILLARRK 6222004 MSFT 10013)
ACPI: MCFG 3F131D18, 003C (r1 A M I GMCH945. 6222004 MSFT 97)
ACPI: SSDT 3EFDE918, 0425 (r1 TrmRef PtidDevc 1000 INTL 20060912)
ACPI: SSDT 3EFEC698, 05F9 (r1 PmRef CpuPm 3000 INTL 20060912)
No NUMA configuration found
Faking a node at 0000000000000000-000000003e7dd000
Entering add_active_range(0, 0, 157) 0 entries of 3200 used
Entering add_active_range(0, 256, 255965) 1 entries of 3200 used
Bootmem setup node 0 0000000000000000-000000003e7dd000
[ffffe20000000000-ffffe200001fffff] PMD ->ffff810001200000 on node 0
[ffffe20000200000-ffffe200003fffff] PMD ->ffff810001600000 on node 0
[ffffe20000400000-ffffe200005fffff] PMD ->ffff810001a00000 on node 0
[ffffe20000600000-ffffe200007fffff] PMD ->ffff810001e00000 on node 0
[ffffe20000800000-ffffe200009fffff] PMD ->ffff810002200000 on node 0
[ffffe20000a00000-ffffe20000bfffff] PMD ->ffff810002600000 on node 0
[ffffe20000c00000-ffffe20000dfffff] PMD ->ffff810002a00000 on node 0
Zone PFN ranges:
DMA 0 -> 4096
DMA32 4096 -> 1048576
Normal 1048576 -> 1048576
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
0: 0 -> 157
0: 256 -> 255965
On node 0 totalpages: 255866
DMA zone: 56 pages used for memmap
DMA zone: 1949 pages reserved
DMA zone: 1992 pages, LIFO batch:0
DMA32 zone: 3443 pages used for memmap
DMA32 zone: 248426 pages, LIFO batch:31
Normal zone: 0 pages used for memmap
Movable zone: 0 pages used for memmap
ACPI: PM-Timer IO Port: 0x408
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 (Bootup-CPU)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Processor #1
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] disabled)
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] disabled)
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Setting APIC routing to flat
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 40000000 (gap: 3f500000:a0b00000)
SMP: Allowing 4 CPUs, 2 hotplug CPUs
PERCPU: Allocating 63928 bytes of per cpu data
Built 1 zonelists in Node order, mobility grouping on. Total pages: 250418
Policy zone: DMA32
Kernel command line: ro root=/dev/VolGroup00/LogVol00 pci=nommconf rhgb quiet
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
Extended CMOS year: 2000
TSC calibrated against PM_TIMER
time.c: Detected 2400.092 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
Checking aperture...
Memory: 997612k/1023860k available (2496k kernel code, 25852k reserved, 1183k
data, 280k init)
Calibrating delay using timer specific routine.. 4802.29 BogoMIPS (lpj=2401149)
Security Framework initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
Mount-cache hash table entries: 256
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU 0/0 -> Node 0
using mwait in idle threads.
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU0: Thermal monitoring enabled (TM2)
SMP alternatives: switching to UP code
ACPI: Core revision 20070126
Using local APIC timer interrupts.
APIC timer calibration result 12500462
Detected 12.500 MHz APIC timer.
SMP alternatives: switching to SMP code
Booting processor 1/2 APIC 0x1
Initializing CPU#1
Calibrating delay using timer specific routine.. 4800.03 BogoMIPS (lpj=2400018)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU 1/1 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU1: Thermal monitoring enabled (TM2)
Intel(R) Core(TM)2 Duo CPU T7700 @ 2.40GHz stepping 0a
checking TSC synchronization [CPU#0 -> CPU#1]: passed.
Brought up 2 CPUs
CPU0 attaching sched-domain:
domain 0: span
00000000,00000000,00000000,00000000,00000000,00000000,00000000,00000003
groups:
00000000,00000000,00000000,00000000,00000000,00000000,00000000,00000001
00000000,00000000,00000000,00000000,00000000,00000000,00000000,00000002
domain 1: span
00000000,00000000,00000000,00000000,00000000,00000000,00000000,00000003
groups:
00000000,00000000,00000000,00000000,00000000,00000000,00000000,00000003
CPU1 attaching sched-domain:
domain 0: span
00000000,00000000,00000000,00000000,00000000,00000000,00000000,00000003
groups:
00000000,00000000,00000000,00000000,00000000,00000000,00000000,00000002
00000000,00000000,00000000,00000000,00000000,00000000,00000000,00000001
domain 1: span
00000000,00000000,00000000,00000000,00000000,00000000,00000000,00000003
groups:
00000000,00000000,00000000,00000000,00000000,00000000,00000000,00000003
net_namespace: 120 bytes
NET: Registered protocol family 16
ACPI: ACPI Dock Station Driver
ACPI: bus type pci registered
PCI: Using configuration type 1
ACPI: EC: Look up EC in DSDT
ACPI: System BIOS is requesting _OSI(Linux)
ACPI: If "acpi_osi=Linux" works better,
Please send dmidecode to [EMAIL PROTECTED]
ACPI: Interpreter enabled
ACPI: (supports S0 S3 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: EC: GPE = 0x17, I/O: command/status = 0x66, data = 0x62
ACPI: EC: driver started in poll mode
ACPI: EC: non-query interrupt received, switching to interrupt mode
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 *10 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 *10 12 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 10 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 5 6 7 *11 12 14 15)
ACPI: Power Resource [FN00] (off)
ACPI: Power Resource [FN01] (off)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 12 devices
ACPI: ACPI bus type pnp unregistered
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
PCI-GART: No AMD northbridge found.
Time: tsc clocksource has been installed.
system 00:04: ioport range 0x680-0x69f has been reserved
system 00:04: ioport range 0x1000-0x100f has been reserved
system 00:04: ioport range 0xffff-0xffff has been reserved
system 00:04: ioport range 0xffff-0xffff has been reserved
system 00:04: ioport range 0x400-0x47f has been reserved
system 00:04: ioport range 0x500-0x53f has been reserved
system 00:04: ioport range 0x164e-0x164f has been reserved
system 00:05: ioport range 0x6a0-0x6af has been reserved
system 00:05: ioport range 0x6b0-0x6ef has been reserved
system 00:0b: iomem range 0xfed1c000-0xfed1ffff could not be reserved
system 00:0b: iomem range 0xfed14000-0xfed17fff has been reserved
system 00:0b: iomem range 0xfed18000-0xfed18fff has been reserved
system 00:0b: iomem range 0xfed19000-0xfed19fff has been reserved
system 00:0b: iomem range 0xe0000000-0xefffffff could not be reserved
system 00:0b: iomem range 0xfed20000-0xfed3ffff has been reserved
system 00:0b: iomem range 0xfeb00000-0xfeb03fff has been reserved
system 00:0b: iomem range 0xfed45000-0xfed8ffff has been reserved
PCI: Bridge: 0000:00:1e.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Setting latency timer of device 0000:00:1e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 6, 262144 bytes)
TCP established hash table entries: 131072 (order: 9, 2097152 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 3085k freed
audit: initializing netlink socket (disabled)
audit(1199815131.419:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Boot video device is 0000:00:02.0
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: Fan [FAN0] (off)
ACPI: Fan [FAN1] (off)
ACPI: SSDT 3EFEDA98, 02E9 (r1 PmRef Cpu0Ist 3000 INTL 20060912)
ACPI: SSDT 3EFF0618, 05B8 (r1 PmRef Cpu0Cst 3001 INTL 20060912)
Monitor-Mwait will be used to enter C-1 state
Monitor-Mwait will be used to enter C-2 state
ACPI: CPU0 (power states: C1[C1] C2[C2])
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI: SSDT 3EFEDE18, 01CF (r1 PmRef ApIst 3000 INTL 20060912)
ACPI: SSDT 3EFEEF18, 008D (r1 PmRef ApCst 3000 INTL 20060912)
ACPI: CPU1 (power states: C1[C1] C2[C2])
ACPI: Processor [CPU1] (supports 8 throttling states)
ACPI Exception (processor_core-0816): AE_NOT_FOUND, Processor Device is not
present [20070126]
ACPI Exception (processor_core-0816): AE_NOT_FOUND, Processor Device is not
present [20070126]
ACPI: Thermal Zone [TZ00] (24 C)
Marking TSC unstable due to possible TSC halt in C2
ACPI: Thermal Zone [TZ01] (24 C)
Time: acpi_pm clocksource has been installed.
Real Time Clock Driver v1.12ac
Non-volatile memory driver v1.2
Linux agpgart interface v0.102
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS2 at I/O 0x3e8 (irq = 3) is a 16550A
00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 16384K size 4096 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Probing IDE interface ide0...
Clocksource tsc unstable (delta = -461188352 ns)
Probing IDE interface ide1...
ide-floppy driver 0.99.newide
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
TCP bic registered
Initializing XFRM netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
registered taskstats version 1
Freeing unused kernel memory: 280k freed
Write protecting the kernel read-only data: 868k
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1a.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1a.0 to 64
uhci_hcd 0000:00:1a.0: UHCI Host Controller
uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1a.0: irq 16, io base 0x000020e0
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1a.1[B] -> GSI 21 (level, low) -> IRQ 21
PCI: Setting latency timer of device 0000:00:1a.1 to 64
uhci_hcd 0000:00:1a.1: UHCI Host Controller
uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1a.1: irq 21, io base 0x000020c0
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 23
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.0: irq 23, io base 0x000020a0
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.1: irq 19, io base 0x00002080
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.2: irq 18, io base 0x00002060
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 6
uhci_hcd 0000:00:1d.3: irq 16, io base 0x00002040
usb usb6: configuration #1 chosen from 1 choice
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 2 ports detected
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
ACPI: PCI Interrupt 0000:00:1a.7[C] -> GSI 19 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1a.7 to 64
ehci_hcd 0000:00:1a.7: EHCI Host Controller
ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 7
ehci_hcd 0000:00:1a.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1a.7
ehci_hcd 0000:00:1a.7: irq 19, io mem 0x50521c00
ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb7: configuration #1 chosen from 1 choice
hub 7-0:1.0: USB hub found
hub 7-0:1.0: 4 ports detected
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 23
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 8
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 23, io mem 0x50521800
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb8: configuration #1 chosen from 1 choice
hub 8-0:1.0: USB hub found
hub 8-0:1.0: 8 ports detected
input: ImPS/2 Generic Wheel Mouse as /class/input/input0
input: AT Translated Set 2 keyboard as /class/input/input1
SCSI subsystem initialized
Driver 'sd' needs updating - please use bus_type methods
libata version 3.00 loaded.
ahci 0000:00:1f.2: version 3.0
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 19
ahci 0000:00:1f.2: AHCI 0001.0200 32 slots 4 ports 3 Gbps 0x33 impl SATA mode
ahci 0000:00:1f.2: flags: 64bit ncq sntf pm led clo pmp pio slum part
PCI: Setting latency timer of device 0000:00:1f.2 to 64
scsi0 : ahci
scsi1 : ahci
scsi2 : ahci
scsi3 : ahci
scsi4 : ahci
scsi5 : ahci
ata1: SATA max UDMA/133 abar [EMAIL PROTECTED] port 0x50521100 irq 8415
ata2: SATA max UDMA/133 abar [EMAIL PROTECTED] port 0x50521180 irq 8415
ata3: DUMMY
ata4: DUMMY
ata5: SATA max UDMA/133 abar [EMAIL PROTECTED] port 0x50521300 irq 8415
ata6: SATA max UDMA/133 abar [EMAIL PROTECTED] port 0x50521380 irq 8415
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ATA-7: ST3750640NS, 3.AEG, max UDMA/133
ata1.00: 1465149168 sectors, multi 16: LBA48 NCQ (depth 31/32)
ata1.00: configured for UDMA/133
ata2: SATA link down (SStatus 0 SControl 300)
ata5: SATA link down (SStatus 0 SControl 300)
ata6: SATA link down (SStatus 0 SControl 300)
scsi 0:0:0:0: Direct-Access ATA ST3750640NS 3.AE PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors (750156 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
sda: sda1 sda2
sd 0:0:0:0: [sda] Attached SCSI disk
device-mapper: ioctl: 4.12.0-ioctl (2007-10-02) initialised: [EMAIL PROTECTED]
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
audit(1199815140.915:2): enforcing=1 old_enforcing=0 auid=4294967295
SELinux:8192 avtab hash slots allocated.Num of rules:57675
SELinux:8192 avtab hash slots allocated.Num of rules:57675
security: 3 users, 6 roles, 1658 types, 210 bools, 1 sens, 1024 cats
security: 61 classes, 57675 rules
SELinux: Completing initialization.
SELinux: Setting up existing superblocks.
SELinux: initialized (dev dm-0, type ext3), uses xattr
SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev debugfs, type debugfs), uses genfs_contexts
SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts
SELinux: initialized (dev mqueue, type mqueue), uses transition SIDs
SELinux: initialized (dev hugetlbfs, type hugetlbfs), uses genfs_contexts
SELinux: initialized (dev devpts, type devpts), uses transition SIDs
SELinux: initialized (dev inotifyfs, type inotifyfs), uses genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev futexfs, type futexfs), uses genfs_contexts
SELinux: initialized (dev anon_inodefs, type anon_inodefs), not configured for
labeling
SELinux: initialized (dev pipefs, type pipefs), uses task SIDs
SELinux: initialized (dev sockfs, type sockfs), uses task SIDs
SELinux: initialized (dev proc, type proc), uses genfs_contexts
SELinux: initialized (dev bdev, type bdev), uses genfs_contexts
SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts
SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
SELinux: policy loaded with handle_unknown=deny
audit(1199815141.173:3): policy loaded auid=4294967295
ACPI: PCI Interrupt 0000:00:1f.3[C] -> GSI 19 (level, low) -> IRQ 19
input: PC Speaker as /class/input/input2
input: Power Button (FF) as /class/input/input3
ACPI: Power Button (FF) [PWRF]
input: Lid Switch as /class/input/input4
ACPI: Lid Switch [LID0]
input: Power Button (CM) as /class/input/input5
ACPI: Power Button (CM) [PWRB]
ACPI: AC Adapter [ADP1] (on-line)
sd 0:0:0:0: Attached scsi generic sg0 type 0
ACPI: Battery Slot [BAT0] (battery present)
ACPI: Battery Slot [BAT1] (battery absent)
ACPI: Battery Slot [BAT2] (battery absent)
floppy0: no floppy controllers found
lp: driver loaded but no devices found
SELinux: initialized (dev ramfs, type ramfs), uses genfs_contexts
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
mtrr: no more MTRRs available
mtrr: no more MTRRs available
mtrr: no more MTRRs available
mtrr: no more MTRRs available
md: Autodetecting RAID arrays.
md: Scanned 0 and added 0 devices.
md: autorun ...
md: ... autorun DONE.
device-mapper: multipath: version 1.0.5 loaded
EXT3 FS on dm-0, internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev sda1, type ext3), uses xattr
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
Adding 2031608k swap on /dev/VolGroup00/LogVol01. Priority:-1 extents:1
across:2031608k
SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses genfs_contexts
IA-32 Microcode Update Driver: v1.14a <[EMAIL PROTECTED]>
warning: process `kudzu' used the deprecated sysctl system call with 1.23.
ip6_tables: (C) 2000-2006 Netfilter Core Team
ip_tables: (C) 2000-2006 Netfilter Core Team
audit(1199843961.837:4): audit_pid=2182 old=0 by auid=4294967295
subj=system_u:system_r:auditd_t:s0
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
SELinux: initialized (dev rpc_pipefs, type rpc_pipefs), uses genfs_contexts
Bluetooth: Core ver 2.11
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.9
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.8
Bluetooth: HIDP (Human Interface Emulation) ver 1.2
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
mtrr: no more MTRRs available
mtrr: no more MTRRs available
mtrr: no more MTRRs available
mtrr: no more MTRRs available
ata6: exception Emask 0x10 SAct 0x0 SErr 0x4050000 action 0xa frozen
ata6: irq_stat 0x00400040, connection status changed
ata6: SError: { PHYRdyChg CommWake DevExch }
ata6: hard resetting link
ata6: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata6.15: Port Multiplier 1.1, 0x1095:0x3726 r23, 6 ports, feat 0x1/0x9
ata6.00: hard resetting link
ata6.00: failed to read SCR 0 (Emask=0x40)
ata6.00: failed to read SCR 0 (Emask=0x40)
ata6.00: failed to read SCR 1 (Emask=0x40)
ata6.00: failed to read SCR 0 (Emask=0x40)
ata6.01: failed to read SCR 2 (Emask=0x40)
ata6.01: hard resetting link
ata6.01: failed to read SCR 2 (Emask=0x40)
ata6.01: failed to read SCR 2 (Emask=0x40)
ata6.01: COMRESET failed (errno=-5)
ata6.01: failed to read SCR 0 (Emask=0x40)
ata6.01: reset failed, giving up
ata6.15: hard resetting link
ata6.15: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata6.00: hard resetting link
ata6.00: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata6.01: hard resetting link
ata6.01: failed to read SCR 0 (Emask=0x40)
ata6.01: failed to read SCR 0 (Emask=0x40)
ata6.01: failed to read SCR 1 (Emask=0x40)
ata6.01: failed to read SCR 0 (Emask=0x40)
ata6.02: failed to read SCR 2 (Emask=0x40)
ata6.02: hard resetting link
ata6.02: failed to read SCR 2 (Emask=0x40)
ata6.02: failed to read SCR 2 (Emask=0x40)
ata6.02: COMRESET failed (errno=-5)
ata6.02: failed to read SCR 0 (Emask=0x40)
ata6.02: reset failed, giving up
ata6.15: hard resetting link
ata6.15: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata6.00: hard resetting link
ata6.00: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata6.01: hard resetting link
ata6.01: failed to read SCR 0 (Emask=0x40)
ata6.01: failed to read SCR 0 (Emask=0x40)
ata6.01: failed to read SCR 1 (Emask=0x40)
ata6.01: failed to read SCR 0 (Emask=0x40)
ata6.02: failed to read SCR 2 (Emask=0x40)
ata6.02: hard resetting link
ata6.02: failed to read SCR 2 (Emask=0x40)
ata6.02: failed to read SCR 2 (Emask=0x40)
ata6.02: COMRESET failed (errno=-5)
ata6.02: failed to read SCR 0 (Emask=0x40)
ata6.02: reset failed, giving up
ata6.15: hard resetting link
ata6.15: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata6.00: hard resetting link
ata6.00: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata6.01: hard resetting link
ata6.01: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
ata6.02: hard resetting link
ata6.02: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
ata6.03: hard resetting link
ata6.03: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata6.04: hard resetting link
ata6.04: SATA link down (SStatus 0 SControl 320)
ata6.05: hard resetting link
ata6.05: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata6.00: ATA-7: ST380815AS, 3.AAC, max UDMA/133
ata6.00: 156301488 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata6.00: configured for UDMA/133
ata6.01: ATA-7: ST3750640NS, 3.AEG, max UDMA/133
ata6.01: 1465149168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata6.01: configured for UDMA/133
ata6.02: ATA-7: ST3750640NS, 3.AEG, max UDMA/133
ata6.02: 1465149168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata6.02: configured for UDMA/133
ata6.03: ATA-7: ST3120813AS, 3.AAE, max UDMA/133
ata6.03: 234441648 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata6.03: configured for UDMA/133
ata6.15: exception Emask 0x10 SAct 0x0 SErr 0x0 action 0x1 t4
ata6.15: irq_stat 0x08000000, interface fatal error
ata6: EH complete
scsi 5:0:0:0: Direct-Access ATA ST380815AS 3.AA PQ: 0 ANSI: 5
sd 5:0:0:0: [sdb] 156301488 512-byte hardware sectors (80026 MB)
sd 5:0:0:0: [sdb] Write Protect is off
sd 5:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 5:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
sd 5:0:0:0: [sdb] 156301488 512-byte hardware sectors (80026 MB)
sd 5:0:0:0: [sdb] Write Protect is off
sd 5:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 5:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
sdb:
sd 5:0:0:0: [sdb] Attached SCSI disk
sd 5:0:0:0: Attached scsi generic sg1 type 0
scsi 5:1:0:0: Direct-Access ATA ST3750640NS 3.AE PQ: 0 ANSI: 5
sd 5:1:0:0: [sdc] 1465149168 512-byte hardware sectors (750156 MB)
sd 5:1:0:0: [sdc] Write Protect is off
sd 5:1:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 5:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
sd 5:1:0:0: [sdc] 1465149168 512-byte hardware sectors (750156 MB)
sd 5:1:0:0: [sdc] Write Protect is off
sd 5:1:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 5:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
sdc:
sd 5:1:0:0: [sdc] Attached SCSI disk
sd 5:1:0:0: Attached scsi generic sg2 type 0
scsi 5:2:0:0: Direct-Access ATA ST3750640NS 3.AE PQ: 0 ANSI: 5
sd 5:2:0:0: [sdd] 1465149168 512-byte hardware sectors (750156 MB)
sd 5:2:0:0: [sdd] Write Protect is off
sd 5:2:0:0: [sdd] Mode Sense: 00 3a 00 00
sd 5:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
sd 5:2:0:0: [sdd] 1465149168 512-byte hardware sectors (750156 MB)
sd 5:2:0:0: [sdd] Write Protect is off
sd 5:2:0:0: [sdd] Mode Sense: 00 3a 00 00
sd 5:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
sdd:
sd 5:2:0:0: [sdd] Attached SCSI disk
sd 5:2:0:0: Attached scsi generic sg3 type 0
scsi 5:3:0:0: Direct-Access ATA ST3120813AS 3.AA PQ: 0 ANSI: 5
sd 5:3:0:0: [sde] 234441648 512-byte hardware sectors (120034 MB)
sd 5:3:0:0: [sde] Write Protect is off
sd 5:3:0:0: [sde] Mode Sense: 00 3a 00 00
sd 5:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
sd 5:3:0:0: [sde] 234441648 512-byte hardware sectors (120034 MB)
sd 5:3:0:0: [sde] Write Protect is off
sd 5:3:0:0: [sde] Mode Sense: 00 3a 00 00
sd 5:3:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
sde:
sd 5:3:0:0: [sde] Attached SCSI disk
sd 5:3:0:0: Attached scsi generic sg4 type 0
usb 8-1: new high speed USB device using ehci_hcd and address 2
usb 8-1: configuration #1 chosen from 1 choice
Initializing USB Mass Storage driver...
scsi6 : SCSI emulation for USB Mass Storage devices
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
scsi 6:0:0:0: Direct-Access SanDisk U3 Titanium 2.18 PQ: 0 ANSI: 2
sd 6:0:0:0: [sdf] 4013713 512-byte hardware sectors (2055 MB)
sd 6:0:0:0: [sdf] Write Protect is off
sd 6:0:0:0: [sdf] Mode Sense: 03 00 00 00
sd 6:0:0:0: [sdf] Assuming drive cache: write through
sd 6:0:0:0: [sdf] 4013713 512-byte hardware sectors (2055 MB)
sd 6:0:0:0: [sdf] Write Protect is off
sd 6:0:0:0: [sdf] Mode Sense: 03 00 00 00
sd 6:0:0:0: [sdf] Assuming drive cache: write through
sdf: unknown partition table
sd 6:0:0:0: [sdf] Attached SCSI removable disk
sd 6:0:0:0: Attached scsi generic sg5 type 0
usb-storage: device scan complete
SELinux: initialized (dev sdf, type vfat), uses genfs_contexts
