Hello, Am Mo, 28.01.2008, 01:17, schrieb Tejun Heo: > Hello, > > > [EMAIL PROTECTED] wrote: >> With one, two and three drives on the pm I got no errors, so I tried to >> change the power supply. I got two power supplies for the 16 >> harddrives and the second one (with all Maxtor drives and the first pm) >> was failing. After changing the power supply all problems where gone. >> Sorry for the >> confusion. > > It's amazing that, in SATA, PSU-problem-verified / PSU-problem-suggested > ratio is significant. I don't think this ever was the case with PATA. SATA > link seems much more susceptible to power quality and allows hooking up > whole lot of drives. > > >> The only remaining issue is that some sata links are only working with >> 1.5 >> gbps and I can't figure out why. (ata3,4,5,6.x are the Maxtor drives and >> ata7,8,9,10.x are the Samsung ones) >> > > Hmm... That's how the hardware negotiated transfer rate w/ each other. > SControl is telling the hardware that there's no speed limit and to go > as high as it can but somehow 3.0Gbps negotiation failed and the link speed > is limited to 1.5Gbps for some of the ports. Is the result always the > same? What happens if you swap drives between ports? Also, if you have > an extra PSU lying around, can you hook it up with some of the drives such > that the load is more distributed. > > Oh.. Another note on PSU. I don't know whether this still holds for > more recent ones but mid-to-high range multi-lane PSUs sometimes have > lesser juice on 12v rail available for disks than low cost single lane > PSUs. This is because high power 12v lanes are allocated to power video > cards and disks can only pull power from (usually) single weak 12v lane. > > Thanks. > > > -- > tejun > >
Shuffling the drives did not change anything to the linkspeed of the 3 ports running with 1.5 Gbps. Looks like the problem is port-related. The first PSU (Multilane) offers (measured) 12,20 V on both lanes. This falls during read/write access on all drives attached down to 12,10 V. The second PSU (Singlelane) offers (measured) 11,75 V. This doesn't change during read/write access on all drives attached. I tested the second PSU without anything attached and it still offered 11,75 V. I will try to add another PSU this evening and remeasure. Currently the whole machine needs about 350W. The PSUs are Targan 500W (Multilane - 2x12V 10A) and Noname 350W (Singlelane - 1x12V 10A) so this 'should' be enough... This night i copied the backup back to the first raid (the Maxtor drives) without any error but during the transfer i got this on the second (mounted but unused) raid: ata10.00: failed to read SCR 1 (Emask=0x40) ata10.01: failed to read SCR 1 (Emask=0x40) ata10.02: failed to read SCR 1 (Emask=0x40) ata10.03: failed to read SCR 1 (Emask=0x40) ata10.04: failed to read SCR 1 (Emask=0x40) ata10.05: failed to read SCR 1 (Emask=0x40) ata10.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen ata10.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen ata10.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen ata10.02: cmd ea/00:00:00:00:00/00:00:00:00:00/a0 tag 1 cdb 0x0 data 0 res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) ata10.02: status: { DRDY } ata10.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen ata10.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen ata10.05: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen ata10.15: hard resetting link ata10.15: SATA link up 3.0 Gbps (SStatus 123 SControl 0) ata10.00: hard resetting link ata10.00: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata10.01: hard resetting link ata10.01: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata10.02: hard resetting link ata10.02: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata10.03: hard resetting link ata10.03: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata10.04: hard resetting link ata10.04: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata10.05: hard resetting link ata10.05: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata10.00: configured for UDMA/100 ata10.01: configured for UDMA/100 ata10.02: configured for UDMA/100 ata10.03: configured for UDMA/100 ata10.04: configured for UDMA/100 ata10: EH complete sd 9:0:0:0: [sdp] 976773168 512-byte hardware sectors (500108 MB) sd 9:0:0:0: [sdp] Write Protect is off sd 9:0:0:0: [sdp] Mode Sense: 00 3a 00 00 sd 9:0:0:0: [sdp] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 9:1:0:0: [sdq] 976773168 512-byte hardware sectors (500108 MB) sd 9:1:0:0: [sdq] Write Protect is off sd 9:1:0:0: [sdq] Mode Sense: 00 3a 00 00 sd 9:1:0:0: [sdq] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 9:2:0:0: [sdr] 976773168 512-byte hardware sectors (500108 MB) sd 9:2:0:0: [sdr] Write Protect is off sd 9:2:0:0: [sdr] Mode Sense: 00 3a 00 00 sd 9:2:0:0: [sdr] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 9:3:0:0: [sds] 976773168 512-byte hardware sectors (500108 MB) sd 9:3:0:0: [sds] Write Protect is off sd 9:3:0:0: [sds] Mode Sense: 00 3a 00 00 sd 9:3:0:0: [sds] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 9:4:0:0: [sdt] 976773168 512-byte hardware sectors (500108 MB) sd 9:4:0:0: [sdt] Write Protect is off sd 9:4:0:0: [sdt] Mode Sense: 00 3a 00 00 sd 9:4:0:0: [sdt] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 9:0:0:0: [sdp] 976773168 512-byte hardware sectors (500108 MB) sd 9:0:0:0: [sdp] Write Protect is off sd 9:0:0:0: [sdp] Mode Sense: 00 3a 00 00 sd 9:0:0:0: [sdp] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 9:1:0:0: [sdq] 976773168 512-byte hardware sectors (500108 MB) sd 9:1:0:0: [sdq] Write Protect is off sd 9:1:0:0: [sdq] Mode Sense: 00 3a 00 00 sd 9:1:0:0: [sdq] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 9:2:0:0: [sdr] 976773168 512-byte hardware sectors (500108 MB) sd 9:2:0:0: [sdr] Write Protect is off sd 9:2:0:0: [sdr] Mode Sense: 00 3a 00 00 sd 9:2:0:0: [sdr] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 9:3:0:0: [sds] 976773168 512-byte hardware sectors (500108 MB) sd 9:3:0:0: [sds] Write Protect is off sd 9:3:0:0: [sds] Mode Sense: 00 3a 00 00 sd 9:3:0:0: [sds] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 9:4:0:0: [sdt] 976773168 512-byte hardware sectors (500108 MB) sd 9:4:0:0: [sdt] Write Protect is off sd 9:4:0:0: [sdt] Mode Sense: 00 3a 00 00 sd 9:4:0:0: [sdt] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA ata10.00: failed to read SCR 1 (Emask=0x40) ata10.01: failed to read SCR 1 (Emask=0x40) ata10.02: failed to read SCR 1 (Emask=0x40) ata10.03: failed to read SCR 1 (Emask=0x40) ata10.04: failed to read SCR 1 (Emask=0x40) ata10.05: failed to read SCR 1 (Emask=0x40) ata10.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen ata10.01: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen ata10.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen ata10.02: cmd ea/00:00:00:00:00/00:00:00:00:00/a0 tag 1 cdb 0x0 data 0 res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) ata10.02: status: { DRDY } ata10.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen ata10.03: cmd ea/00:00:00:00:00/00:00:00:00:00/a0 tag 3 cdb 0x0 data 0 res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) ata10.03: status: { DRDY } ata10.04: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen ata10.05: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen ata10.15: hard resetting link ata10.15: SATA link up 3.0 Gbps (SStatus 123 SControl 0) ata10.00: hard resetting link ata10.00: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata10.01: hard resetting link ata10.01: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata10.02: hard resetting link ata10.02: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata10.03: hard resetting link ata10.03: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata10.04: hard resetting link ata10.04: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata10.05: hard resetting link ata10.05: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata10.00: configured for UDMA/100 ata10.01: configured for UDMA/100 ata10.02: configured for UDMA/100 ata10.03: configured for UDMA/100 ata10.04: configured for UDMA/100 ata10: EH complete sd 9:0:0:0: [sdp] 976773168 512-byte hardware sectors (500108 MB) sd 9:0:0:0: [sdp] Write Protect is off sd 9:0:0:0: [sdp] Mode Sense: 00 3a 00 00 sd 9:0:0:0: [sdp] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 9:1:0:0: [sdq] 976773168 512-byte hardware sectors (500108 MB) sd 9:1:0:0: [sdq] Write Protect is off sd 9:1:0:0: [sdq] Mode Sense: 00 3a 00 00 sd 9:1:0:0: [sdq] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 9:2:0:0: [sdr] 976773168 512-byte hardware sectors (500108 MB) sd 9:2:0:0: [sdr] Write Protect is off sd 9:2:0:0: [sdr] Mode Sense: 00 3a 00 00 sd 9:2:0:0: [sdr] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 9:3:0:0: [sds] 976773168 512-byte hardware sectors (500108 MB) sd 9:3:0:0: [sds] Write Protect is off sd 9:3:0:0: [sds] Mode Sense: 00 3a 00 00 sd 9:3:0:0: [sds] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 9:4:0:0: [sdt] 976773168 512-byte hardware sectors (500108 MB) sd 9:4:0:0: [sdt] Write Protect is off sd 9:4:0:0: [sdt] Mode Sense: 00 3a 00 00 sd 9:4:0:0: [sdt] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 9:0:0:0: [sdp] 976773168 512-byte hardware sectors (500108 MB) sd 9:0:0:0: [sdp] Write Protect is off sd 9:0:0:0: [sdp] Mode Sense: 00 3a 00 00 sd 9:0:0:0: [sdp] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 9:1:0:0: [sdq] 976773168 512-byte hardware sectors (500108 MB) sd 9:1:0:0: [sdq] Write Protect is off sd 9:1:0:0: [sdq] Mode Sense: 00 3a 00 00 sd 9:1:0:0: [sdq] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 9:2:0:0: [sdr] 976773168 512-byte hardware sectors (500108 MB) sd 9:2:0:0: [sdr] Write Protect is off sd 9:2:0:0: [sdr] Mode Sense: 00 3a 00 00 sd 9:2:0:0: [sdr] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 9:3:0:0: [sds] 976773168 512-byte hardware sectors (500108 MB) sd 9:3:0:0: [sds] Write Protect is off sd 9:3:0:0: [sds] Mode Sense: 00 3a 00 00 sd 9:3:0:0: [sds] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 9:4:0:0: [sdt] 976773168 512-byte hardware sectors (500108 MB) sd 9:4:0:0: [sdt] Write Protect is off sd 9:4:0:0: [sdt] Mode Sense: 00 3a 00 00 sd 9:4:0:0: [sdt] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA - To unsubscribe from this list: send the line "unsubscribe linux-ide" in the body of a message to [EMAIL PROTECTED] More majordomo info at http://vger.kernel.org/majordomo-info.html