http://bugzilla.kernel.org/show_bug.cgi?id=9994
Summary: atiixp ide timeouts Product: IO/Storage Version: 2.5 KernelVersion: 2.6.24 Platform: All OS/Version: Linux Tree: Mainline Status: NEW Severity: normal Priority: P1 Component: IDE AssignedTo: [EMAIL PROTECTED] ReportedBy: [EMAIL PROTECTED] Latest working kernel version:2.6.23 Earliest failing kernel version:2.6.24 Distribution:gentoo Hardware Environment:Acer Aspire 5021 Software Environment: Problem Description: After some hours of uptime I can find this in dmesg and dma of my harddrive is switched off: ... hda: irq timeout: status=0xd0 { Busy } hda: irq timeout: status=0xd0 { Busy } hda: status timeout: status=0xd0 { Busy } hda: DMA disabled ... I can switch it back with hdparm -d1 /dev/hda, but after some hours the same thing happens. Steps to reproduce: just wait, the attached dmesg contains 26 ide0 resets during 17 hours uptime lspci -v: 00:00.0 Host bridge: ATI Technologies Inc RS480 Host Bridge (rev 01) Subsystem: Acer Incorporated [ALI] Aspire 5024WLMMi Flags: bus master, 66MHz, medium devsel, latency 64 00:02.0 PCI bridge: ATI Technologies Inc RS480 PCI-X Root Port (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 00009000-00009fff Memory behind bridge: c0100000-c01fffff Prefetchable memory behind bridge: c8000000-cfffffff Capabilities: [50] Power Management version 3 Capabilities: [58] Express Root Port (Slot-), MSI 00 Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable- Capabilities: [b0] Subsystem: ATI Technologies Inc Unknown device 5950 Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+ 00:06.0 PCI bridge: ATI Technologies Inc RS480 PCI Bridge (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=09, subordinate=09, sec-latency=0 Capabilities: [50] Power Management version 3 Capabilities: [58] Express Root Port (Slot-), MSI 00 Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable- Capabilities: [b0] Subsystem: ATI Technologies Inc Unknown device 5950 Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+ 00:07.0 PCI bridge: ATI Technologies Inc RS480 PCI Bridge (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=04, subordinate=05, sec-latency=0 Capabilities: [50] Power Management version 3 Capabilities: [58] Express Root Port (Slot-), MSI 00 Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable- Capabilities: [b0] Subsystem: ATI Technologies Inc Unknown device 5950 Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+ 00:13.0 USB Controller: ATI Technologies Inc IXP SB400 USB Host Controller (prog-if 10 [OHCI]) Subsystem: Acer Incorporated [ALI] Unknown device 0080 Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 11 Memory at c0000000 (32-bit, non-prefetchable) [size=4K] Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable- 00:13.1 USB Controller: ATI Technologies Inc IXP SB400 USB Host Controller (prog-if 10 [OHCI]) Subsystem: Acer Incorporated [ALI] Aspire 5024WLMMi Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 11 Memory at c0001000 (32-bit, non-prefetchable) [size=4K] Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable- 00:13.2 USB Controller: ATI Technologies Inc IXP SB400 USB2 Host Controller (prog-if 20 [EHCI]) Subsystem: Acer Incorporated [ALI] Aspire 5024WLMMi Flags: 66MHz, medium devsel, IRQ 11 Memory at c0002000 (32-bit, non-prefetchable) [size=4K] Capabilities: [dc] Power Management version 2 Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable- 00:14.0 SMBus: ATI Technologies Inc IXP SB400 SMBus Controller (rev 11) Subsystem: Acer Incorporated [ALI] Aspire 5024WLMMi Flags: 66MHz, medium devsel I/O ports at 8400 [size=16] Memory at c0003000 (32-bit, non-prefetchable) [size=1K] Capabilities: [b0] HyperTransport: MSI Mapping Enable- Fixed+ 00:14.1 IDE interface: ATI Technologies Inc Standard Dual Channel PCI IDE Controller (prog-if 8a [Master SecP PriP]) Subsystem: Acer Incorporated [ALI] Aspire 5024WLMMi Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 16 I/O ports at 01f0 [size=8] I/O ports at 03f4 [size=1] I/O ports at 0170 [size=8] I/O ports at 0374 [size=1] I/O ports at 8410 [size=16] Capabilities: [70] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable- 00:14.3 ISA bridge: ATI Technologies Inc IXP SB400 PCI-ISA Bridge Subsystem: Acer Incorporated [ALI] Aspire 5024WLMi Flags: bus master, 66MHz, medium devsel, latency 0 00:14.4 PCI bridge: ATI Technologies Inc IXP SB400 PCI-PCI Bridge (prog-if 01 [Subtractive decode]) Flags: bus master, 66MHz, medium devsel, latency 64 Bus: primary=00, secondary=06, subordinate=06, sec-latency=64 I/O behind bridge: 0000a000-0000afff Memory behind bridge: c0200000-c02fffff 00:14.5 Multimedia audio controller: ATI Technologies Inc IXP SB400 AC'97 Audio Controller (rev 02) Subsystem: Acer Incorporated [ALI] Aspire 5024WLMMi Flags: bus master, 66MHz, slow devsel, latency 64, IRQ 17 Memory at c0003400 (32-bit, non-prefetchable) [size=256] Capabilities: [40] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable- 00:14.6 Modem: ATI Technologies Inc SB400 AC'97 Modem Controller (rev 02) (prog-if 00 [Generic]) Subsystem: Acer Incorporated [ALI] Aspire 5024WLMMi Flags: bus master, 66MHz, slow devsel, latency 64, IRQ 11 Memory at c0003800 (32-bit, non-prefetchable) [size=256] Capabilities: [40] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable- 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration Flags: fast devsel Capabilities: [80] HyperTransport: Host or Secondary Interface 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map Flags: fast devsel 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller Flags: fast devsel 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control Flags: fast devsel 01:00.0 VGA compatible controller: ATI Technologies Inc Radeon Mobility X700 (PCIE) (prog-if 00 [VGA]) Subsystem: Acer Incorporated [ALI] Aspire 5024WLMi Flags: bus master, fast devsel, latency 0, IRQ 18 Memory at c8000000 (32-bit, prefetchable) [size=128M] I/O ports at 9000 [size=256] Memory at c0100000 (32-bit, non-prefetchable) [size=64K] [virtual] Expansion ROM at c0120000 [disabled] [size=128K] Capabilities: [50] Power Management version 2 Capabilities: [58] Express Endpoint, MSI 00 Capabilities: [80] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable- 06:05.0 Network controller: Broadcom Corporation BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller (rev 02) Subsystem: AMBIT Microsystem Corp. Aspire 3022WLMi, 5024WLMi, 5020 Flags: bus master, fast devsel, latency 64, IRQ 21 Memory at c0204000 (32-bit, non-prefetchable) [size=8K] 06:06.0 CardBus bridge: Texas Instruments PCIxx21/x515 Cardbus Controller Subsystem: Acer Incorporated [ALI] Aspire 5024WLMi Flags: bus master, medium devsel, latency 64, IRQ 20 Memory at c020a000 (32-bit, non-prefetchable) [size=4K] Bus: primary=06, secondary=07, subordinate=08, sec-latency=176 Memory window 0: 60000000-63fff000 (prefetchable) Memory window 1: 64000000-67fff000 (prefetchable) I/O window 0: 0000a400-0000a4ff I/O window 1: 0000a800-0000a8ff 16-bit legacy interface ports at 0001 06:06.2 FireWire (IEEE 1394): Texas Instruments OHCI Compliant IEEE 1394 Host Controller (prog-if 10 [OHCI]) Subsystem: Acer Incorporated [ALI] Aspire 5024WLMi Flags: bus master, medium devsel, latency 64, IRQ 22 Memory at c0208000 (32-bit, non-prefetchable) [size=2K] Memory at c0200000 (32-bit, non-prefetchable) [size=16K] Capabilities: [44] Power Management version 2 06:06.3 Mass storage controller: Texas Instruments PCIxx21 Integrated FlashMedia Controller Subsystem: Acer Incorporated [ALI] Aspire 5024WLMi Flags: bus master, medium devsel, latency 64, IRQ 11 Memory at c0206000 (32-bit, non-prefetchable) [size=8K] Capabilities: [44] Power Management version 2 06:06.4 Generic system peripheral [0805]: Texas Instruments PCI6411/6421/6611/6621/7411/7421/7611/7621 Secure Digital Controller Subsystem: Acer Incorporated [ALI] Aspire 5024WLMi Flags: bus master, medium devsel, latency 64, IRQ 11 Memory at c0209000 (32-bit, non-prefetchable) [size=256] Memory at c0208c00 (32-bit, non-prefetchable) [size=256] Memory at c0208800 (32-bit, non-prefetchable) [size=256] Capabilities: [80] Power Management version 2 06:07.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8169 Gigabit Ethernet (rev 10) Subsystem: Acer Incorporated [ALI] Aspire 5024WLMi Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 11 I/O ports at a000 [size=256] Memory at c0209400 (32-bit, non-prefetchable) [size=256] [virtual] Expansion ROM at c0220000 [disabled] [size=128K] Capabilities: [dc] Power Management version 2 dmesg: Linux version 2.6.24-gentoo-r2 ([EMAIL PROTECTED]) (gcc version 4.2.2 (Gentoo 4.2.2 p1.0)) #2 PREEMPT Mon Feb 11 18:58:21 CET 2008 Command line: root=/dev/hda5 udev powernow-k8.vcore_list=1125,925 usbcore.autosuspend=1 hpet=force BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009b800 (usable) BIOS-e820: 000000000009b800 - 00000000000a0000 (reserved) BIOS-e820: 00000000000d0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000004fea0000 (usable) BIOS-e820: 000000004fea0000 - 000000004feae000 (ACPI data) BIOS-e820: 000000004feae000 - 000000004ff00000 (ACPI NVS) BIOS-e820: 000000004ff00000 - 0000000050000000 (reserved) BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved) Entering add_active_range(0, 0, 155) 0 entries of 256 used Entering add_active_range(0, 256, 327328) 1 entries of 256 used end_pfn_map = 1048576 DMI 2.3 present. ACPI: RSDP 000F6DA0, 0014 (r0 PTLTD ) ACPI: RSDT 4FEA81E3, 0034 (r1 PTLTD RSDT 6040000 LTP 0) ACPI: FACP 4FEADE41, 0074 (r1 ATI Piranha 6040000 ATI F4240) ACPI: DSDT 4FEA8217, 5C2A (r1 ATI SB400 6040000 MSFT 100000E) ACPI: FACS 4FEAEFC0, 0040 ACPI: SSDT 4FEADEB5, 00B5 (r1 PTLTD POWERNOW 6040000 LTP 1) ACPI: APIC 4FEADF6A, 005A (r1 PTLTD APIC 6040000 LTP 0) ACPI: MCFG 4FEADFC4, 003C (r1 PTLTD MCFG 6040000 LTP 0) ACPI: DMI detected: Acer Entering add_active_range(0, 0, 155) 0 entries of 256 used Entering add_active_range(0, 256, 327328) 1 entries of 256 used Zone PFN ranges: DMA 0 -> 4096 DMA32 4096 -> 1048576 Normal 1048576 -> 1048576 Movable zone start PFN for each node early_node_map[2] active PFN ranges 0: 0 -> 155 0: 256 -> 327328 On node 0 totalpages: 327227 DMA zone: 56 pages used for memmap DMA zone: 1371 pages reserved DMA zone: 2568 pages, LIFO batch:0 DMA32 zone: 4419 pages used for memmap DMA32 zone: 318813 pages, LIFO batch:31 Normal zone: 0 pages used for memmap Movable zone: 0 pages used for memmap ATI board detected. Disabling timer routing over 8254. ACPI: PM-Timer IO Port: 0x8008 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) Processor #0 (Bootup-CPU) ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 1, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 21 low level) ACPI: IRQ0 used by override. ACPI: IRQ2 used by override. Setting APIC routing to flat Using ACPI (MADT) for SMP configuration information Allocating PCI resources starting at 60000000 (gap: 50000000:aec00000) Built 1 zonelists in Zone order, mobility grouping on. Total pages: 321381 Kernel command line: root=/dev/hda5 udev powernow-k8.vcore_list=1125,925 usbcore.autosuspend=1 hpet=force Initializing CPU#0 PID hash table entries: 4096 (order: 12, 32768 bytes) TSC calibrated against PM_TIMER time.c: Detected 1599.999 MHz processor. Console: colour VGA+ 80x25 console [tty0] enabled Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes) Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes) Checking aperture... CPU 0: aperture @ 180000000 size 32 MB Aperture too small (32 MB) No AGP bridge found Memory: 1282044k/1309312k available (3486k kernel code, 26556k reserved, 1281k data, 216k init) Calibrating delay using timer specific routine.. 3202.05 BogoMIPS (lpj=1601028) Mount-cache hash table entries: 256 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 512K (64 bytes/line) CPU: AMD Turion(tm) 64 Mobile Technology ML-28 stepping 02 ACPI: Core revision 20070126 ACPI: Table DSDT replaced by host OS ACPI: DSDT 00000000, 5624 (r1 ATI SB400 6040000 INTL 20061109) ACPI: DSDT override uses original SSDTs unless "acpi_no_auto_ssdt"<3>..MP-BIOS bug: 8254 timer not connected to IO-APIC Using local APIC timer interrupts. APIC timer calibration result 12499988 Detected 12.499 MHz APIC timer. net_namespace: 120 bytes NET: Registered protocol family 16 ACPI: bus type pci registered PCI: BIOS Bug: MCFG area at e0000000 is not E820-reserved PCI: Not using MMCONFIG. PCI: Using configuration type 1 ACPI: EC: Look up EC in DSDT ACPI: Interpreter enabled ACPI: (supports S0 S3 S5) ACPI: Using IOAPIC for interrupt routing ACPI: EC: non-query interrupt received, switching to interrupt mode ACPI: EC: GPE = 0x3, I/O: command/status = 0x66, data = 0x62 ACPI: EC: driver started in interrupt mode ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Transparent bridge - 0000:00:14.4 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PB6_._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PB7_._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP1._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKB] (IRQs 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKC] (IRQs 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKD] (IRQs 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKE] (IRQs 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKF] (IRQs 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKG] (IRQs 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKH] (IRQs 10 11) *0, disabled. Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init ACPI: bus type pnp registered pnp: PnP ACPI: found 10 devices ACPI: ACPI bus type pnp unregistered SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report PCI: Cannot allocate resource region 7 of bridge 0000:00:06.0 PCI: Cannot allocate resource region 8 of bridge 0000:00:06.0 PCI: Cannot allocate resource region 7 of bridge 0000:00:07.0 PCI: Cannot allocate resource region 8 of bridge 0000:00:07.0 ACPI: RTC can wake from S4 Time: tsc clocksource has been installed. system 00:01: iomem range 0xe0000000-0xefffffff has been reserved system 00:01: iomem range 0xfec00000-0xfec00fff could not be reserved system 00:01: iomem range 0xfee00000-0xfee00fff could not be reserved system 00:08: ioport range 0x1080-0x1080 has been reserved system 00:08: ioport range 0x1200-0x120f has been reserved system 00:08: ioport range 0x500-0x51f has been reserved system 00:08: ioport range 0x40b-0x40b has been reserved system 00:08: ioport range 0x4d0-0x4d1 has been reserved system 00:08: ioport range 0x4d6-0x4d6 has been reserved system 00:08: ioport range 0xc00-0xc01 has been reserved system 00:08: ioport range 0xc14-0xc14 has been reserved system 00:08: ioport range 0xc50-0xc52 has been reserved system 00:08: ioport range 0xc6c-0xc6c has been reserved system 00:08: ioport range 0xc6f-0xc6f has been reserved system 00:08: ioport range 0xcd4-0xcd5 has been reserved system 00:08: ioport range 0xcd6-0xcd7 has been reserved system 00:08: ioport range 0xcd8-0xcdf has been reserved system 00:08: ioport range 0x8000-0x805f has been reserved system 00:08: ioport range 0xf40-0xf47 has been reserved system 00:08: ioport range 0x87f-0x87f has been reserved system 00:09: iomem range 0xe0000-0xfffff could not be reserved system 00:09: iomem range 0xfff80000-0xffffffff could not be reserved system 00:09: iomem range 0x0-0xfff could not be reserved PCI: Bridge: 0000:00:02.0 IO window: 9000-9fff MEM window: c0100000-c01fffff PREFETCH window: c8000000-cfffffff PCI: Bridge: 0000:00:06.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:07.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bus 7, cardbus bridge: 0000:06:06.0 IO window: 0000a400-0000a4ff IO window: 0000a800-0000a8ff PREFETCH window: 60000000-63ffffff MEM window: 64000000-67ffffff PCI: Bridge: 0000:00:14.4 IO window: a000-afff MEM window: c0200000-c02fffff PREFETCH window: disabled. PCI: Setting latency timer of device 0000:00:02.0 to 64 PCI: Setting latency timer of device 0000:00:06.0 to 64 PCI: Setting latency timer of device 0000:00:07.0 to 64 ACPI: PCI Interrupt 0000:06:06.0[A] -> GSI 20 (level, low) -> IRQ 20 NET: Registered protocol family 2 IP route cache hash table entries: 65536 (order: 7, 524288 bytes) TCP established hash table entries: 262144 (order: 10, 4194304 bytes) TCP bind hash table entries: 65536 (order: 7, 524288 bytes) TCP: Hash tables configured (established 262144 bind 65536) TCP reno registered SGI XFS with large block/inode numbers, no debug enabled io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) PCI: MSI quirk detected. MSI deactivated. Boot video device is 0000:01:00.0 PCI: Setting latency timer of device 0000:00:02.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:02.0:pcie00] PCI: Setting latency timer of device 0000:00:06.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:06.0:pcie00] PCI: Setting latency timer of device 0000:00:07.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:07.0:pcie00] Generic RTC Driver v1.07 Linux agpgart interface v0.102 ACPI: AC Adapter [ADP1] (on-line) ACPI: Battery Slot [BAT0] (battery absent) input: Power Button (FF) as /devices/virtual/input/input0 ACPI: Power Button (FF) [PWRF] input: Lid Switch as /devices/virtual/input/input1 ACPI: Lid Switch [LID0] input: Sleep Button (CM) as /devices/virtual/input/input2 ACPI: Sleep Button (CM) [SLPB] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3]) ACPI: Thermal Zone [TZS0] (57 C) ACPI: Thermal Zone [TZS1] (53 C) ACPI: Thermal Zone [TZSV] (65 C) loop: module loaded Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx ATIIXP: IDE controller (0x1002:0x4376 rev 0x00) at PCI slot 0000:00:14.1 ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 16 ATIIXP: not 100% native mode: will probe irqs later ide0: BM-DMA at 0x8410-0x8417, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0x8418-0x841f, BIOS settings: hdc:DMA, hdd:pio Probing IDE interface ide0... Switched to high resolution mode on CPU 0 hda: ST9160821A, ATA DISK drive hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4 hda: UDMA/100 mode selected ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 Probing IDE interface ide1... hdc: MATSHITAUJ-845D, ATAPI CD/DVD-ROM drive hdc: host max PIO4 wanted PIO255(auto-tune) selected PIO4 hdc: UDMA/33 mode selected ide1 at 0x170-0x177,0x376 on irq 15 hda: max request size: 512KiB hda: 312581808 sectors (160041 MB) w/8192KiB Cache, CHS=19457/255/63 hda: cache flushes supported hda: hda1 hda2 hda3 < hda5 hda6 > hdc: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache Uniform CD-ROM driver Revision: 3.20 Driver 'sd' needs updating - please use bus_type methods ACPI: PCI Interrupt 0000:06:06.2[C] -> GSI 22 (level, low) -> IRQ 22 firewire_ohci: Added fw-ohci device 0000:06:06.2, OHCI version 1.10 PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12 i8042.c: Detected active multiplexing controller, rev 1.1. serio: i8042 KBD port at 0x60,0x64 irq 1 serio: i8042 AUX0 port at 0x60,0x64 irq 12 serio: i8042 AUX1 port at 0x60,0x64 irq 12 serio: i8042 AUX2 port at 0x60,0x64 irq 12 serio: i8042 AUX3 port at 0x60,0x64 irq 12 mice: PS/2 mouse device common for all mice input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input3 rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0 rtc0: alarms up to one month i2c /dev entries driver device-mapper: ioctl: 4.12.0-ioctl (2007-10-02) initialised: [EMAIL PROTECTED] cpuidle: using governor ladder firewire_core: created new fw device fw0 (0 config rom retries, S400) Synaptics Touchpad, model: 1, fw: 6.2, id: 0x12a0b1, caps: 0xa04713/0x204000 input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio4/input/input4 cpuidle: using governor menu Advanced Linux Sound Architecture Driver Version 1.0.15 (Tue Nov 20 19:16:42 2007 UTC). ALSA device list: No soundcards found. TCP cubic registered NET: Registered protocol family 1 NET: Registered protocol family 17 RPC: Registered udp transport module. RPC: Registered tcp transport module. powernow-k8: Found 1 AMD Turion(tm) 64 Mobile Technology ML-28 processors (1 cpu cores) (version 2.20.00) powernow-k8: Requested Voltage for id0 is 1125 mV default voltage is 1450 powernow-k8: Performing required adjustment of 325 mV or 13 25mV steps powernow-k8: Requested Voltage for id1 is 925 mV default voltage is 1000 powernow-k8: Performing required adjustment of 75 mV or 3 25mV steps powernow-k8: 0 : fid 0x8 (1600 MHz), vid 0x11 powernow-k8: 1 : fid 0x0 (800 MHz), vid 0x19 rtc_cmos 00:04: setting system clock to 2008-02-14 08:47:44 UTC (1202978864) Marking TSC unstable due to TSC halts in idle Time: acpi_pm clocksource has been installed. XFS mounting filesystem hda5 Starting XFS recovery on filesystem: hda5 (logdev: internal) Ending XFS recovery on filesystem: hda5 (logdev: internal) VFS: Mounted root (xfs filesystem) readonly. Freeing unused kernel memory: 216k freed Clocksource tsc unstable (delta = -91005859 ns) ACPI: WMI-Acer: Mapper loaded acer_acpi: Acer Laptop ACPI Extras version 0.10.0 acer_acpi: Detected Acer AMW0 interface Registered led device: acer_acpi:mail fuse init (API version 7.9) ndiswrapper version 1.52 loaded (smp=no, preempt=yes) ndiswrapper (link_pe_images:576): fixing KI_USER_SHARED_DATA address in the driver ndiswrapper: driver bcmwl5 (Broadcom,02/11/2005, 3.100.64.0) loaded ACPI: PCI Interrupt 0000:06:05.0[A] -> GSI 21 (level, low) -> IRQ 21 ndiswrapper: using IRQ 21 wlan0: ethernet device 00:0e:9b:bf:b0:b8 using NDIS driver: bcmwl5, version: 0x364400a, NDIS version: 0x501, vendor: 'NDIS Network Adapter', 14E4:4318.5.conf wlan0: encryption modes supported: WEP; TKIP with WPA, WPA2, WPA2PSK; AES/CCMP with WPA, WPA2, WPA2PSK usbcore: registered new interface driver ndiswrapper Adding 2449872k swap on /dev/mapper/crypt-swap. Priority:-1 extents:1 across:2449872k ACPI: PCI Interrupt 0000:00:14.5[B] -> GSI 17 (level, low) -> IRQ 17 ndiswrapper: device wlan0 removed ACPI: PCI interrupt for device 0000:06:05.0 disabled usbcore: deregistering interface driver ndiswrapper ndiswrapper version 1.52 loaded (smp=no, preempt=yes) ndiswrapper (link_pe_images:576): fixing KI_USER_SHARED_DATA address in the driver ndiswrapper: driver bcmwl5 (Broadcom,02/11/2005, 3.100.64.0) loaded ACPI: PCI Interrupt 0000:06:05.0[A] -> GSI 21 (level, low) -> IRQ 21 ndiswrapper: using IRQ 21 wlan0: ethernet device 00:0e:9b:bf:b0:b8 using NDIS driver: bcmwl5, version: 0x364400a, NDIS version: 0x501, vendor: 'NDIS Network Adapter', 14E4:4318.5.conf wlan0: encryption modes supported: WEP; TKIP with WPA, WPA2, WPA2PSK; AES/CCMP with WPA, WPA2, WPA2PSK usbcore: registered new interface driver ndiswrapper [drm] Initialized drm 1.1.0 20060810 ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 18 (level, low) -> IRQ 18 PCI: Setting latency timer of device 0000:01:00.0 to 64 [drm] Initialized radeon 1.28.0 20060524 on minor 0 [drm] Setting GART location based on new memory map [drm] Loading R300 Microcode [drm] writeback test succeeded in 1 usecs XFS mounting filesystem hda6 Starting XFS recovery on filesystem: hda6 (logdev: internal) Ending XFS recovery on filesystem: hda6 (logdev: internal) APIC error on CPU0: 00(40) hda: irq timeout: status=0xd0 { Busy } ide: failed opcode was: 0xea hda: status timeout: status=0xd0 { Busy } ide: failed opcode was: unknown hda: DMA disabled hda: drive not ready for command ide0: reset: master: error (0x00?) hda: status error: status=0x00 { } ide: failed opcode was: unknown hda: drive not ready for command hda: status error: status=0x00 { } ide: failed opcode was: unknown hda: drive not ready for command hda: status error: status=0x10 { SeekComplete } ide: failed opcode was: unknown hda: drive not ready for command hda: status error: status=0x10 { SeekComplete } ide: failed opcode was: unknown hda: drive not ready for command ide0: reset: success hda: status timeout: status=0xd0 { Busy } ide: failed opcode was: unknown hda: no DRQ after issuing MULTWRITE_EXT ide0: reset: success hda: status timeout: status=0xd0 { Busy } ide: failed opcode was: unknown hda: no DRQ after issuing MULTWRITE_EXT ide0: reset: success hda: status timeout: status=0xd0 { Busy } ide: failed opcode was: unknown hda: no DRQ after issuing MULTWRITE_EXT ide0: reset: success hda: status timeout: status=0xd0 { Busy } ide: failed opcode was: unknown hda: no DRQ after issuing MULTWRITE_EXT ide0: reset: success hda: status timeout: status=0xd0 { Busy } ide: failed opcode was: unknown hda: no DRQ after issuing MULTWRITE_EXT ide0: reset: success hda: irq timeout: status=0xd0 { Busy } ide: failed opcode was: 0xea hda: status timeout: status=0xd0 { Busy } ide: failed opcode was: unknown hda: drive not ready for command ide0: reset: success APIC error on CPU0: 40(40) hda: status timeout: status=0xd0 { Busy } ide: failed opcode was: unknown hda: no DRQ after issuing MULTWRITE_EXT ide0: reset: success hda: status timeout: status=0xd0 { Busy } ide: failed opcode was: unknown hda: no DRQ after issuing MULTWRITE_EXT ide0: reset: success hda: status timeout: status=0xd0 { Busy } ide: failed opcode was: unknown hda: no DRQ after issuing MULTWRITE_EXT ide0: reset: success hda: irq timeout: status=0xd0 { Busy } ide: failed opcode was: unknown ide0: reset timed-out, status=0x80 hda: status timeout: status=0x80 { Busy } ide: failed opcode was: unknown hda: drive not ready for command ide0: reset: success hda: irq timeout: status=0xd0 { Busy } ide: failed opcode was: 0xea hda: status timeout: status=0xd0 { Busy } ide: failed opcode was: unknown hda: drive not ready for command ide0: reset timed-out, status=0x80 hda: status timeout: status=0x80 { Busy } ide: failed opcode was: unknown hda: drive not ready for command ide0: reset: success hda: irq timeout: status=0xd0 { Busy } ide: failed opcode was: 0xea hda: status timeout: status=0xd0 { Busy } ide: failed opcode was: unknown hda: drive not ready for command ide0: reset timed-out, status=0x80 hda: status timeout: status=0x80 { Busy } ide: failed opcode was: unknown hda: drive not ready for command ide0: reset: success hda: irq timeout: status=0xd0 { Busy } ide: failed opcode was: 0xea hda: status timeout: status=0xd0 { Busy } ide: failed opcode was: unknown hda: no DRQ after issuing MULTWRITE_EXT ide0: reset: success hda: status timeout: status=0xd0 { Busy } ide: failed opcode was: unknown hda: no DRQ after issuing MULTWRITE_EXT ide0: reset: success psmouse.c: TouchPad at isa0060/serio4/input0 lost synchronization, throwing 2 bytes away. hda: status timeout: status=0xd0 { Busy } ide: failed opcode was: unknown hda: no DRQ after issuing MULTWRITE_EXT ide0: reset: success hda: status timeout: status=0xd0 { Busy } ide: failed opcode was: unknown hda: no DRQ after issuing MULTWRITE_EXT ide0: reset: success hda: status timeout: status=0xd0 { Busy } ide: failed opcode was: unknown hda: no DRQ after issuing MULTWRITE_EXT ide0: reset: success hda: status timeout: status=0xd0 { Busy } ide: failed opcode was: unknown hda: no DRQ after issuing MULTWRITE_EXT ide0: reset: success hda: status timeout: status=0xd0 { Busy } ide: failed opcode was: unknown hda: no DRQ after issuing MULTWRITE_EXT ide0: reset: success hda: status timeout: status=0xd0 { Busy } ide: failed opcode was: unknown hda: no DRQ after issuing MULTWRITE_EXT ide0: reset: success hda: status timeout: status=0xd0 { Busy } ide: failed opcode was: unknown hda: no DRQ after issuing MULTWRITE_EXT ide0: reset: success -- Configure bugmail: http://bugzilla.kernel.org/userprefs.cgi?tab=email ------- You are receiving this mail because: ------- You are the assignee for the bug, or are watching the assignee. - To unsubscribe from this list: send the line "unsubscribe linux-ide" in the body of a message to [EMAIL PROTECTED] More majordomo info at http://vger.kernel.org/majordomo-info.html