Hi Dmitry,
I believe these two patches were simply forgotten. Could you review them
again please? I don't have access to the hardware any more, but I'd
still like to have the patches mainline.
Thanks,
Daniel
On 22.05.2013 19:57, Daniel Mack wrote:
> Allocate a copy of the pdata, and keep a pointer to it in the private
> struct ads7846. Also, kill some members that used to be in both structs.
>
> This is needed for the upcoming DT support.
>
> Signed-off-by: Daniel Mack <zon...@gmail.com>
> ---
>
> Hi Dmitry,
>
> this is the alternative approach, as described eariler in our email
> thread. It works equally well.
>
> Thanks for having another look.
>
> I'm resending this after 10 days of silence, to make sure it isn't
> lost :)
>
>
> Daniel
>
>
> drivers/input/touchscreen/ads7846.c | 78
> ++++++++++++++++++++-----------------
> 1 file changed, 43 insertions(+), 35 deletions(-)
>
> diff --git a/drivers/input/touchscreen/ads7846.c
> b/drivers/input/touchscreen/ads7846.c
> index 84ccf14..198677d 100644
> --- a/drivers/input/touchscreen/ads7846.c
> +++ b/drivers/input/touchscreen/ads7846.c
> @@ -104,12 +104,8 @@ struct ads7846 {
> #endif
>
> u16 model;
> - u16 vref_mv;
> u16 vref_delay_usecs;
> - u16 x_plate_ohms;
> - u16 pressure_max;
>
> - bool swap_xy;
> bool use_internal;
>
> struct ads7846_packet *packet;
> @@ -143,6 +139,9 @@ struct ads7846 {
> int gpio_pendown;
>
> void (*wait_for_sync)(void);
> +
> + /* platform data from board file or DT */
> + struct ads7846_platform_data *pdata;
> };
>
> /* leave chip selected when we're done, for quicker re-select? */
> @@ -456,7 +455,7 @@ static inline unsigned vaux_adjust(struct ads7846 *ts,
> ssize_t v)
> unsigned retval = v;
>
> /* external resistors may scale vAUX into 0..vREF */
> - retval *= ts->vref_mv;
> + retval *= ts->pdata->vref_mv;
> retval = retval >> 12;
>
> return retval;
> @@ -515,25 +514,25 @@ static int ads784x_hwmon_register(struct spi_device
> *spi, struct ads7846 *ts)
> /* hwmon sensors need a reference voltage */
> switch (ts->model) {
> case 7846:
> - if (!ts->vref_mv) {
> + if (!ts->pdata->vref_mv) {
> dev_dbg(&spi->dev, "assuming 2.5V internal vREF\n");
> - ts->vref_mv = 2500;
> + ts->pdata->vref_mv = 2500;
> ts->use_internal = true;
> }
> break;
> case 7845:
> case 7843:
> - if (!ts->vref_mv) {
> + if (!ts->pdata->vref_mv) {
> dev_warn(&spi->dev,
> "external vREF for ADS%d not specified\n",
> - ts->model);
> + ts->pdata->model);
> return 0;
> }
> break;
> }
>
> /* different chips have different sensor groups */
> - switch (ts->model) {
> + switch (ts->pdata->model) {
> case 7846:
> ts->attr_group = &ads7846_attr_group;
> break;
> @@ -544,7 +543,7 @@ static int ads784x_hwmon_register(struct spi_device *spi,
> struct ads7846 *ts)
> ts->attr_group = &ads7843_attr_group;
> break;
> default:
> - dev_dbg(&spi->dev, "ADS%d not recognized\n", ts->model);
> + dev_dbg(&spi->dev, "ADS%d not recognized\n", ts->pdata->model);
> return 0;
> }
>
> @@ -700,7 +699,7 @@ static int ads7846_get_value(struct ads7846 *ts, struct
> spi_message *m)
> struct spi_transfer *t =
> list_entry(m->transfers.prev, struct spi_transfer,
> transfer_list);
>
> - if (ts->model == 7845) {
> + if (ts->pdata->model == 7845) {
> return be16_to_cpup((__be16 *)&(((char*)t->rx_buf)[1])) >> 3;
> } else {
> /*
> @@ -776,6 +775,7 @@ static void ads7846_read_state(struct ads7846 *ts)
> static void ads7846_report_state(struct ads7846 *ts)
> {
> struct ads7846_packet *packet = ts->packet;
> + struct ads7846_platform_data *pdata = ts->pdata;
> unsigned int Rt;
> u16 x, y, z1, z2;
>
> @@ -784,7 +784,7 @@ static void ads7846_report_state(struct ads7846 *ts)
> * from on-the-wire format as part of debouncing to get stable
> * readings.
> */
> - if (ts->model == 7845) {
> + if (pdata->model == 7845) {
> x = *(u16 *)packet->tc.x_buf;
> y = *(u16 *)packet->tc.y_buf;
> z1 = 0;
> @@ -800,11 +800,11 @@ static void ads7846_report_state(struct ads7846 *ts)
> if (x == MAX_12BIT)
> x = 0;
>
> - if (ts->model == 7843) {
> - Rt = ts->pressure_max / 2;
> - } else if (ts->model == 7845) {
> + if (pdata->model == 7843) {
> + Rt = pdata->pressure_max / 2;
> + } else if (pdata->model == 7845) {
> if (get_pendown_state(ts))
> - Rt = ts->pressure_max / 2;
> + Rt = pdata->pressure_max / 2;
> else
> Rt = 0;
> dev_vdbg(&ts->spi->dev, "x/y: %d/%d, PD %d\n", x, y, Rt);
> @@ -813,7 +813,7 @@ static void ads7846_report_state(struct ads7846 *ts)
> Rt = z2;
> Rt -= z1;
> Rt *= x;
> - Rt *= ts->x_plate_ohms;
> + Rt *= pdata->x_plate_ohms;
> Rt /= z1;
> Rt = (Rt + 2047) >> 12;
> } else {
> @@ -825,7 +825,7 @@ static void ads7846_report_state(struct ads7846 *ts)
> * the maximum. Don't report it to user space, repeat at least
> * once more the measurement
> */
> - if (packet->tc.ignore || Rt > ts->pressure_max) {
> + if (packet->tc.ignore || Rt > pdata->pressure_max) {
> dev_vdbg(&ts->spi->dev, "ignored %d pressure %d\n",
> packet->tc.ignore, Rt);
> return;
> @@ -853,7 +853,7 @@ static void ads7846_report_state(struct ads7846 *ts)
> if (Rt) {
> struct input_dev *input = ts->input;
>
> - if (ts->swap_xy)
> + if (pdata->swap_xy)
> swap(x, y);
>
> if (!ts->pendown) {
> @@ -864,7 +864,7 @@ static void ads7846_report_state(struct ads7846 *ts)
>
> input_report_abs(input, ABS_X, x);
> input_report_abs(input, ABS_Y, y);
> - input_report_abs(input, ABS_PRESSURE, ts->pressure_max - Rt);
> + input_report_abs(input, ABS_PRESSURE, pdata->pressure_max - Rt);
>
> input_sync(input);
> dev_vdbg(&ts->spi->dev, "%4d/%4d/%4d\n", x, y, Rt);
> @@ -963,7 +963,7 @@ static SIMPLE_DEV_PM_OPS(ads7846_pm, ads7846_suspend,
> ads7846_resume);
> static int ads7846_setup_pendown(struct spi_device *spi,
> struct ads7846 *ts)
> {
> - struct ads7846_platform_data *pdata = spi->dev.platform_data;
> + struct ads7846_platform_data *pdata = ts->pdata;
> int err;
>
> /*
> @@ -1003,20 +1003,20 @@ static int ads7846_setup_pendown(struct spi_device
> *spi,
> * use formula #2 for pressure, not #3.
> */
> static void ads7846_setup_spi_msg(struct ads7846 *ts,
> - const struct ads7846_platform_data *pdata)
> + struct ads7846_platform_data *pdata)
> {
> struct spi_message *m = &ts->msg[0];
> struct spi_transfer *x = ts->xfer;
> struct ads7846_packet *packet = ts->packet;
> int vref = pdata->keep_vref_on;
>
> - if (ts->model == 7873) {
> + if (pdata->model == 7873) {
> /*
> * The AD7873 is almost identical to the ADS7846
> * keep VREF off during differential/ratiometric
> * conversion modes.
> */
> - ts->model = 7846;
> + pdata->model = 7846;
> vref = 0;
> }
>
> @@ -1024,7 +1024,7 @@ static void ads7846_setup_spi_msg(struct ads7846 *ts,
> spi_message_init(m);
> m->context = ts;
>
> - if (ts->model == 7845) {
> + if (pdata->model == 7845) {
> packet->read_y_cmd[0] = READ_Y(vref);
> packet->read_y_cmd[1] = 0;
> packet->read_y_cmd[2] = 0;
> @@ -1069,7 +1069,7 @@ static void ads7846_setup_spi_msg(struct ads7846 *ts,
> spi_message_init(m);
> m->context = ts;
>
> - if (ts->model == 7845) {
> + if (pdata->model == 7845) {
> x++;
> packet->read_x_cmd[0] = READ_X(vref);
> packet->read_x_cmd[1] = 0;
> @@ -1108,7 +1108,7 @@ static void ads7846_setup_spi_msg(struct ads7846 *ts,
> }
>
> /* turn y+ off, x- on; we'll use formula #2 */
> - if (ts->model == 7846) {
> + if (pdata->model == 7846) {
> ts->msg_count++;
> m++;
> spi_message_init(m);
> @@ -1178,7 +1178,7 @@ static void ads7846_setup_spi_msg(struct ads7846 *ts,
> spi_message_init(m);
> m->context = ts;
>
> - if (ts->model == 7845) {
> + if (pdata->model == 7845) {
> x++;
> packet->pwrdown_cmd[0] = PWRDOWN;
> packet->pwrdown_cmd[1] = 0;
> @@ -1247,19 +1247,27 @@ static int ads7846_probe(struct spi_device *spi)
>
> spi_set_drvdata(spi, ts);
>
> + ts->pdata = pdata;
> ts->packet = packet;
> ts->spi = spi;
> ts->input = input_dev;
> - ts->vref_mv = pdata->vref_mv;
> - ts->swap_xy = pdata->swap_xy;
>
> mutex_init(&ts->lock);
> init_waitqueue_head(&ts->wait);
>
> - ts->model = pdata->model ? : 7846;
> - ts->vref_delay_usecs = pdata->vref_delay_usecs ? : 100;
> - ts->x_plate_ohms = pdata->x_plate_ohms ? : 400;
> - ts->pressure_max = pdata->pressure_max ? : ~0;
> + /* pdata fallback defaults */
> +
> + if (!pdata->model)
> + pdata->model = 7846;
> +
> + if (!pdata->vref_delay_usecs)
> + pdata->vref_delay_usecs = 100;
> +
> + if (!pdata->x_plate_ohms)
> + pdata->x_plate_ohms = 400;
> +
> + if (!pdata->pressure_max)
> + pdata->pressure_max = ~0;
>
> if (pdata->filter != NULL) {
> if (pdata->filter_init != NULL) {
>
--
To unsubscribe from this list: send the line "unsubscribe linux-input" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
