Hi, On Tuesday 17 November 2015 10:17:20 Dmitry Torokhov wrote: > On Mon, Nov 16, 2015 at 01:01:07PM +0100, Markus Pargmann wrote: > > This is a driver for the imx25 ADC/TSC module. It controls the > > touchscreen conversion queue and creates a touchscreen input device. > > The driver currently only supports 4 wire touchscreens. The driver uses > > a simple conversion queue of precharge, touch detection, X measurement, > > Y measurement, precharge and another touch detection. > > > > This driver uses the regmap from the parent to setup some touch specific > > settings in the core driver and setup a idle configuration with touch > > detection. > > > > Signed-off-by: Markus Pargmann <[email protected]> > > Signed-off-by: Denis Carikli <[email protected]> > > > > [fix clock's period calculation] > > [fix calculation of the 'settling' value] > > Signed-off-by: Juergen Borleis <[email protected]> > > --- > > > > Notes: > > Changes in v7: > > - Moved clk_prepare_enable() and mx25_tcq_init() into mx25_tcq_open(). > > This > > was done to be able to use devm_request_threaded_irq(). > > - Cleanup of the probe function through above change > > - Removed mx25_tcq_remove(), not necessary now > > > > drivers/input/touchscreen/Kconfig | 6 + > > drivers/input/touchscreen/Makefile | 1 + > > drivers/input/touchscreen/fsl-imx25-tcq.c | 600 > > ++++++++++++++++++++++++++++++ > > 3 files changed, 607 insertions(+) > > create mode 100644 drivers/input/touchscreen/fsl-imx25-tcq.c > > > > diff --git a/drivers/input/touchscreen/Kconfig > > b/drivers/input/touchscreen/Kconfig > > index ae33da7ab51f..b44651d33080 100644 > > --- a/drivers/input/touchscreen/Kconfig > > +++ b/drivers/input/touchscreen/Kconfig > > @@ -811,6 +811,12 @@ config TOUCHSCREEN_USB_COMPOSITE > > To compile this driver as a module, choose M here: the > > module will be called usbtouchscreen. > > > > +config TOUCHSCREEN_MX25 > > + tristate "Freescale i.MX25 touchscreen input driver" > > + depends on MFD_MX25_TSADC > > + help > > + Enable support for touchscreen connected to your i.MX25. > > + > > To compile this driver as a module... > > > config TOUCHSCREEN_MC13783 > > tristate "Freescale MC13783 touchscreen input driver" > > depends on MFD_MC13XXX > > diff --git a/drivers/input/touchscreen/Makefile > > b/drivers/input/touchscreen/Makefile > > index cbaa6abb08da..77a2ac54101a 100644 > > --- a/drivers/input/touchscreen/Makefile > > +++ b/drivers/input/touchscreen/Makefile > > @@ -45,6 +45,7 @@ obj-$(CONFIG_TOUCHSCREEN_INTEL_MID) += > > intel-mid-touch.o > > obj-$(CONFIG_TOUCHSCREEN_IPROC) += bcm_iproc_tsc.o > > obj-$(CONFIG_TOUCHSCREEN_LPC32XX) += lpc32xx_ts.o > > obj-$(CONFIG_TOUCHSCREEN_MAX11801) += max11801_ts.o > > +obj-$(CONFIG_TOUCHSCREEN_MX25) += fsl-imx25-tcq.o > > obj-$(CONFIG_TOUCHSCREEN_MC13783) += mc13783_ts.o > > obj-$(CONFIG_TOUCHSCREEN_MCS5000) += mcs5000_ts.o > > obj-$(CONFIG_TOUCHSCREEN_MIGOR) += migor_ts.o > > diff --git a/drivers/input/touchscreen/fsl-imx25-tcq.c > > b/drivers/input/touchscreen/fsl-imx25-tcq.c > > new file mode 100644 > > index 000000000000..c833cd814972 > > --- /dev/null > > +++ b/drivers/input/touchscreen/fsl-imx25-tcq.c > > @@ -0,0 +1,600 @@ > > +/* > > + * Copyright (C) 2014-2015 Pengutronix, Markus Pargmann > > <[email protected]> > > + * > > + * This program is free software; you can redistribute it and/or modify it > > under > > + * the terms of the GNU General Public License version 2 as published by > > the > > + * Free Software Foundation. > > + * > > + * Based on driver from 2011: > > + * Juergen Beisert, Pengutronix <[email protected]> > > + * > > + * This is the driver for the imx25 TCQ (Touchscreen Conversion Queue) > > + * connected to the imx25 ADC. > > + */ > > + > > +#include <linux/clk.h> > > +#include <linux/device.h> > > +#include <linux/input.h> > > +#include <linux/interrupt.h> > > +#include <linux/mfd/imx25-tsadc.h> > > +#include <linux/module.h> > > +#include <linux/of.h> > > +#include <linux/platform_device.h> > > +#include <linux/regmap.h> > > + > > +static const char mx25_tcq_name[] = "mx25-tcq"; > > + > > +enum mx25_tcq_mode { > > + MX25_TS_4WIRE, > > +}; > > + > > +struct mx25_tcq_priv { > > + struct regmap *regs; > > + struct regmap *core_regs; > > + struct input_dev *idev; > > + enum mx25_tcq_mode mode; > > + unsigned int pen_threshold; > > + unsigned int sample_count; > > + unsigned int expected_samples; > > + unsigned int pen_debounce; > > + unsigned int settling_time; > > + struct clk *clk; > > + int irq; > > +}; > > + > > +static struct regmap_config mx25_tcq_regconfig = { > > + .fast_io = true, > > + .max_register = 0x5c, > > + .reg_bits = 32, > > + .val_bits = 32, > > + .reg_stride = 4, > > +}; > > + > > +static const struct of_device_id mx25_tcq_ids[] = { > > + { .compatible = "fsl,imx25-tcq", }, > > + { /* Sentinel */ } > > +}; > > + > > +#define TSC_4WIRE_PRE_INDEX 0 > > +#define TSC_4WIRE_X_INDEX 1 > > +#define TSC_4WIRE_Y_INDEX 2 > > +#define TSC_4WIRE_POST_INDEX 3 > > +#define TSC_4WIRE_LEAVE 4 > > + > > +#define MX25_TSC_DEF_THRESHOLD 80 > > +#define TSC_MAX_SAMPLES 16 > > + > > +#define MX25_TSC_REPEAT_WAIT 14 > > + > > +enum mx25_adc_configurations { > > + MX25_CFG_PRECHARGE = 0, > > + MX25_CFG_TOUCH_DETECT, > > + MX25_CFG_X_MEASUREMENT, > > + MX25_CFG_Y_MEASUREMENT, > > +}; > > + > > +#define MX25_PRECHARGE_VALUE (\ > > + MX25_ADCQ_CFG_YPLL_OFF | \ > > + MX25_ADCQ_CFG_XNUR_OFF | \ > > + MX25_ADCQ_CFG_XPUL_HIGH | \ > > + MX25_ADCQ_CFG_REFP_INT | \ > > + MX25_ADCQ_CFG_IN_XP | \ > > + MX25_ADCQ_CFG_REFN_NGND2 | \ > > + MX25_ADCQ_CFG_IGS) > > + > > +#define MX25_TOUCH_DETECT_VALUE (\ > > + MX25_ADCQ_CFG_YNLR | \ > > + MX25_ADCQ_CFG_YPLL_OFF | \ > > + MX25_ADCQ_CFG_XNUR_OFF | \ > > + MX25_ADCQ_CFG_XPUL_OFF | \ > > + MX25_ADCQ_CFG_REFP_INT | \ > > + MX25_ADCQ_CFG_IN_XP | \ > > + MX25_ADCQ_CFG_REFN_NGND2 | \ > > + MX25_ADCQ_CFG_PENIACK) > > + > > +static void imx25_setup_queue_cfgs(struct mx25_tcq_priv *priv, > > + unsigned int settling_cnt) > > +{ > > + u32 precharge_cfg = > > + MX25_PRECHARGE_VALUE | > > + MX25_ADCQ_CFG_SETTLING_TIME(settling_cnt); > > + u32 touch_detect_cfg = > > + MX25_TOUCH_DETECT_VALUE | > > + MX25_ADCQ_CFG_NOS(1) | > > + MX25_ADCQ_CFG_SETTLING_TIME(settling_cnt); > > + > > + regmap_write(priv->core_regs, MX25_TSC_TICR, precharge_cfg); > > + > > + /* PRECHARGE */ > > + regmap_write(priv->regs, MX25_ADCQ_CFG(MX25_CFG_PRECHARGE), > > + precharge_cfg); > > + > > + /* TOUCH_DETECT */ > > + regmap_write(priv->regs, MX25_ADCQ_CFG(MX25_CFG_TOUCH_DETECT), > > + touch_detect_cfg); > > + > > + /* X Measurement */ > > + regmap_write(priv->regs, MX25_ADCQ_CFG(MX25_CFG_X_MEASUREMENT), > > + MX25_ADCQ_CFG_YPLL_OFF | > > + MX25_ADCQ_CFG_XNUR_LOW | > > + MX25_ADCQ_CFG_XPUL_HIGH | > > + MX25_ADCQ_CFG_REFP_XP | > > + MX25_ADCQ_CFG_IN_YP | > > + MX25_ADCQ_CFG_REFN_XN | > > + MX25_ADCQ_CFG_NOS(priv->sample_count) | > > + MX25_ADCQ_CFG_SETTLING_TIME(settling_cnt)); > > + > > + /* Y Measurement */ > > + regmap_write(priv->regs, MX25_ADCQ_CFG(MX25_CFG_Y_MEASUREMENT), > > + MX25_ADCQ_CFG_YNLR | > > + MX25_ADCQ_CFG_YPLL_HIGH | > > + MX25_ADCQ_CFG_XNUR_OFF | > > + MX25_ADCQ_CFG_XPUL_OFF | > > + MX25_ADCQ_CFG_REFP_YP | > > + MX25_ADCQ_CFG_IN_XP | > > + MX25_ADCQ_CFG_REFN_YN | > > + MX25_ADCQ_CFG_NOS(priv->sample_count) | > > + MX25_ADCQ_CFG_SETTLING_TIME(settling_cnt)); > > + > > + /* Enable the touch detection right now */ > > + regmap_write(priv->core_regs, MX25_TSC_TICR, touch_detect_cfg | > > + MX25_ADCQ_CFG_IGS); > > +} > > + > > +static int imx25_setup_queue_4wire(struct mx25_tcq_priv *priv, > > + unsigned settling_cnt, int *items) > > +{ > > + imx25_setup_queue_cfgs(priv, settling_cnt); > > + > > + /* Setup the conversion queue */ > > + regmap_write(priv->regs, MX25_ADCQ_ITEM_7_0, > > + MX25_ADCQ_ITEM(0, MX25_CFG_PRECHARGE) | > > + MX25_ADCQ_ITEM(1, MX25_CFG_TOUCH_DETECT) | > > + MX25_ADCQ_ITEM(2, MX25_CFG_X_MEASUREMENT) | > > + MX25_ADCQ_ITEM(3, MX25_CFG_Y_MEASUREMENT) | > > + MX25_ADCQ_ITEM(4, MX25_CFG_PRECHARGE) | > > + MX25_ADCQ_ITEM(5, MX25_CFG_TOUCH_DETECT)); > > + > > + /* > > + * We measure X/Y with 'sample_count' number of samples and execute a > > + * touch detection twice, with 1 sample each > > + */ > > + priv->expected_samples = priv->sample_count * 2 + 2; > > + *items = 6; > > + > > + return 0; > > +} > > + > > +static void mx25_tcq_disable_touch_irq(struct mx25_tcq_priv *priv) > > +{ > > + regmap_update_bits(priv->regs, MX25_ADCQ_CR, MX25_ADCQ_CR_PDMSK, > > + MX25_ADCQ_CR_PDMSK); > > +} > > + > > +static void mx25_tcq_enable_touch_irq(struct mx25_tcq_priv *priv) > > +{ > > + regmap_update_bits(priv->regs, MX25_ADCQ_CR, MX25_ADCQ_CR_PDMSK, 0); > > +} > > + > > +static void mx25_tcq_disable_fifo_irq(struct mx25_tcq_priv *priv) > > +{ > > + regmap_update_bits(priv->regs, MX25_ADCQ_MR, MX25_ADCQ_MR_FDRY_IRQ, > > + MX25_ADCQ_MR_FDRY_IRQ); > > +} > > + > > +static void mx25_tcq_enable_fifo_irq(struct mx25_tcq_priv *priv) > > +{ > > + regmap_update_bits(priv->regs, MX25_ADCQ_MR, MX25_ADCQ_MR_FDRY_IRQ, 0); > > +} > > + > > +static void mx25_tcq_force_queue_start(struct mx25_tcq_priv *priv) > > +{ > > + regmap_update_bits(priv->regs, MX25_ADCQ_CR, > > + MX25_ADCQ_CR_FQS, > > + MX25_ADCQ_CR_FQS); > > +} > > + > > +static void mx25_tcq_force_queue_stop(struct mx25_tcq_priv *priv) > > +{ > > + regmap_update_bits(priv->regs, MX25_ADCQ_CR, > > + MX25_ADCQ_CR_FQS, 0); > > +} > > + > > +static void mx25_tcq_fifo_reset(struct mx25_tcq_priv *priv) > > +{ > > + u32 tcqcr; > > + > > + regmap_read(priv->regs, MX25_ADCQ_CR, &tcqcr); > > + regmap_update_bits(priv->regs, MX25_ADCQ_CR, MX25_ADCQ_CR_FRST, > > + MX25_ADCQ_CR_FRST); > > + regmap_update_bits(priv->regs, MX25_ADCQ_CR, MX25_ADCQ_CR_FRST, 0); > > + regmap_write(priv->regs, MX25_ADCQ_CR, tcqcr); > > +} > > + > > +static void mx25_tcq_re_enable_touch_detection(struct mx25_tcq_priv *priv) > > +{ > > + /* stop the queue from looping */ > > + mx25_tcq_force_queue_stop(priv); > > + > > + /* for a clean touch detection, preload the X plane */ > > + regmap_write(priv->core_regs, MX25_TSC_TICR, MX25_PRECHARGE_VALUE); > > + > > + /* waste some time now to pre-load the X plate to high voltage */ > > + mx25_tcq_fifo_reset(priv); > > + > > + /* re-enable the detection right now */ > > + regmap_write(priv->core_regs, MX25_TSC_TICR, > > + MX25_TOUCH_DETECT_VALUE | MX25_ADCQ_CFG_IGS); > > + > > + regmap_update_bits(priv->regs, MX25_ADCQ_SR, MX25_ADCQ_SR_PD, > > + MX25_ADCQ_SR_PD); > > + > > + /* enable the pen down event to be a source for the interrupt */ > > + regmap_update_bits(priv->regs, MX25_ADCQ_MR, MX25_ADCQ_MR_PD_IRQ, 0); > > + > > + /* lets fire the next IRQ if someone touches the touchscreen */ > > + mx25_tcq_enable_touch_irq(priv); > > +} > > + > > +static int mx25_tcq_create_event_for_4wire(struct mx25_tcq_priv *priv, > > Why not void? What callers are supposed to do with the value?
Good point.
>
> > + u32 *sample_buf,
> > + unsigned int samples)
> > +{
> > + unsigned int x_pos = 0;
> > + unsigned int y_pos = 0;
> > + unsigned int touch_pre = 0;
> > + unsigned int touch_post = 0;
> > + unsigned int i;
> > + int ret = 0;
> > +
> > + for (i = 0; i < samples; i++) {
> > + unsigned int index = MX25_ADCQ_FIFO_ID(sample_buf[i]);
> > + unsigned int val = MX25_ADCQ_FIFO_DATA(sample_buf[i]);
> > +
> > + switch (index) {
> > + case 1:
> > + touch_pre = val;
> > + break;
> > + case 2:
> > + x_pos = val;
> > + break;
> > + case 3:
> > + y_pos = val;
> > + break;
> > + case 5:
> > + touch_post = val;
> > + break;
> > + default:
> > + ret = -EINVAL;
> > + break;
> > + }
> > + }
> > +
> > + if (ret == 0 && samples != 0) {
>
> Where do we set ret to anything other than 0?
In the default case above.
I replaced the return -EINVAL with a debug message. This case shouldn't happen
but just in case it does..
>
> > + /*
> > + * only if both touch measures are below a threshold,
> > + * the position is valid
> > + */
> > + if (touch_pre < priv->pen_threshold &&
> > + touch_post < priv->pen_threshold) {
> > + /* valid samples, generate a report */
> > + x_pos /= priv->sample_count;
> > + y_pos /= priv->sample_count;
> > + input_report_abs(priv->idev, ABS_X, x_pos);
> > + input_report_abs(priv->idev, ABS_Y, y_pos);
> > + input_report_key(priv->idev, BTN_TOUCH, 1);
> > + input_sync(priv->idev);
> > +
> > + /* get next sample */
> > + mx25_tcq_enable_fifo_irq(priv);
> > + } else if (touch_pre >= priv->pen_threshold &&
> > + touch_post >= priv->pen_threshold) {
> > + /*
> > + * if both samples are invalid,
> > + * generate a release report
> > + */
> > + input_report_key(priv->idev, BTN_TOUCH, 0);
> > + input_sync(priv->idev);
> > + mx25_tcq_re_enable_touch_detection(priv);
> > + } else {
> > + /*
> > + * if only one of both touch measurements are
> > + * below the threshold, still some bouncing
> > + * happens. Take additional samples in this
> > + * case to be sure
> > + */
> > + mx25_tcq_enable_fifo_irq(priv);
> > + }
> > + }
> > +
> > + return ret;
> > +}
> > +
> > +static irqreturn_t mx25_tcq_irq_thread(int irq, void *dev_id)
> > +{
> > + struct mx25_tcq_priv *priv = dev_id;
> > + u32 sample_buf[TSC_MAX_SAMPLES];
> > + unsigned int samples = 0;
> > +
> > + /* read all samples */
> > + while (1) {
> > + u32 stats;
> > +
> > + regmap_read(priv->regs, MX25_ADCQ_SR, &stats);
> > + if (stats & MX25_ADCQ_SR_EMPT)
> > + break;
> > +
> > + if (samples < TSC_MAX_SAMPLES) {
> > + regmap_read(priv->regs, MX25_ADCQ_FIFO,
> > + &sample_buf[samples]);
> > + ++samples;
> > + } else {
> > + u32 discarded;
> > + /* discard samples */
> > + regmap_read(priv->regs, MX25_ADCQ_FIFO, &discarded);
> > + }
> > + }
> > +
> > + mx25_tcq_create_event_for_4wire(priv, sample_buf, samples);
> > +
> > + return IRQ_HANDLED;
> > +}
> > +
> > +static irqreturn_t mx25_tcq_irq(int irq, void *dev_id)
> > +{
> > + struct mx25_tcq_priv *priv = dev_id;
> > + u32 stat;
> > + int ret = IRQ_HANDLED;
> > +
> > + regmap_read(priv->regs, MX25_ADCQ_SR, &stat);
>
> Is there any concern that these reads will fail?
This is always using mmio and we do not use the register clock feature. So it
shouldn't fail.
>
> > +
> > + if (stat & (MX25_ADCQ_SR_FRR | MX25_ADCQ_SR_FUR | MX25_ADCQ_SR_FOR))
> > + mx25_tcq_fifo_reset(priv);
> > +
> > + if (stat & MX25_ADCQ_SR_PD) {
> > + mx25_tcq_disable_touch_irq(priv);
> > + mx25_tcq_force_queue_start(priv);
> > + mx25_tcq_enable_fifo_irq(priv);
> > + }
> > +
> > + if (stat & MX25_ADCQ_SR_FDRY) {
> > + mx25_tcq_disable_fifo_irq(priv);
> > + ret = IRQ_WAKE_THREAD;
> > + }
> > +
> > + regmap_update_bits(priv->regs, MX25_ADCQ_SR, MX25_ADCQ_SR_FRR |
> > + MX25_ADCQ_SR_FUR | MX25_ADCQ_SR_FOR |
> > + MX25_ADCQ_SR_PD | MX25_ADCQ_SR_EOQ,
> > + MX25_ADCQ_SR_FRR | MX25_ADCQ_SR_FUR |
> > + MX25_ADCQ_SR_FOR | MX25_ADCQ_SR_PD |
> > + MX25_ADCQ_SR_EOQ);
> > +
> > + return ret;
> > +}
> > +
> > +/* configure the statemachine for a 4-wire touchscreen */
> > +static int mx25_tcq_init(struct mx25_tcq_priv *priv)
> > +{
> > + u32 tgcr;
> > + unsigned int ipg_div;
> > + unsigned int adc_period;
> > + unsigned int debounce_cnt;
> > + unsigned int settling_cnt;
> > + int itemct;
> > + int ret;
> > +
> > + regmap_read(priv->core_regs, MX25_TSC_TGCR, &tgcr);
> > + ipg_div = max_t(unsigned int, 4, MX25_TGCR_GET_ADCCLK(tgcr));
> > + adc_period = USEC_PER_SEC * ipg_div * 2 + 2;
> > + adc_period /= clk_get_rate(priv->clk) / 1000 + 1;
> > + debounce_cnt = DIV_ROUND_UP(priv->pen_debounce, adc_period * 8) - 1;
> > + settling_cnt = DIV_ROUND_UP(priv->settling_time, adc_period * 8) - 1;
> > +
> > + /* Reset */
> > + regmap_write(priv->regs, MX25_ADCQ_CR,
> > + MX25_ADCQ_CR_QRST | MX25_ADCQ_CR_FRST);
> > + regmap_update_bits(priv->regs, MX25_ADCQ_CR,
> > + MX25_ADCQ_CR_QRST | MX25_ADCQ_CR_FRST, 0);
> > +
> > + /* up to 128 * 8 ADC clocks are possible */
> > + if (debounce_cnt > 127)
> > + debounce_cnt = 127;
> > +
> > + /* up to 255 * 8 ADC clocks are possible */
> > + if (settling_cnt > 255)
> > + settling_cnt = 255;
> > +
> > + ret = imx25_setup_queue_4wire(priv, settling_cnt, &itemct);
> > + if (ret)
> > + return ret;
> > +
> > + regmap_update_bits(priv->regs, MX25_ADCQ_CR,
> > + MX25_ADCQ_CR_LITEMID_MASK | MX25_ADCQ_CR_WMRK_MASK,
> > + MX25_ADCQ_CR_LITEMID(itemct - 1) |
> > + MX25_ADCQ_CR_WMRK(priv->expected_samples - 1));
> > +
> > + /* setup debounce count */
> > + regmap_update_bits(priv->core_regs, MX25_TSC_TGCR,
> > + MX25_TGCR_PDBTIME_MASK,
> > + MX25_TGCR_PDBTIME(debounce_cnt));
> > +
> > + /* enable debounce */
> > + regmap_update_bits(priv->core_regs, MX25_TSC_TGCR, MX25_TGCR_PDBEN,
> > + MX25_TGCR_PDBEN);
> > + regmap_update_bits(priv->core_regs, MX25_TSC_TGCR, MX25_TGCR_PDEN,
> > + MX25_TGCR_PDEN);
> > +
> > + /* enable the engine on demand */
> > + regmap_update_bits(priv->regs, MX25_ADCQ_CR, MX25_ADCQ_CR_QSM_MASK,
> > + MX25_ADCQ_CR_QSM_FQS);
> > +
> > + /* Enable repeat and repeat wait */
> > + regmap_update_bits(priv->regs, MX25_ADCQ_CR,
> > + MX25_ADCQ_CR_RPT | MX25_ADCQ_CR_RWAIT_MASK,
> > + MX25_ADCQ_CR_RPT |
> > + MX25_ADCQ_CR_RWAIT(MX25_TSC_REPEAT_WAIT));
> > +
> > + mx25_tcq_re_enable_touch_detection(priv);
> > +
> > + return 0;
> > +}
> > +
> > +static int mx25_tcq_parse_dt(struct platform_device *pdev,
> > + struct mx25_tcq_priv *priv)
> > +{
> > + struct device_node *np = pdev->dev.of_node;
> > + u32 wires;
> > + int ret;
> > +
> > + /* Setup defaults */
> > + priv->pen_threshold = 500;
> > + priv->sample_count = 3;
> > + priv->pen_debounce = 1000000;
> > + priv->settling_time = 250000;
> > +
> > + ret = of_property_read_u32(np, "fsl,wires", &wires);
> > + if (ret) {
> > + dev_err(&pdev->dev, "Failed to find fsl,wires properties\n");
> > + return ret;
> > + }
> > +
> > + if (wires == 4) {
> > + priv->mode = MX25_TS_4WIRE;
> > + } else {
> > + dev_err(&pdev->dev, "%u-wire mode not supported\n", wires);
> > + return -EINVAL;
> > + }
> > +
> > + /* These are optional, we don't care about the return values */
> > + of_property_read_u32(np, "fsl,pen-threshold", &priv->pen_threshold);
> > + of_property_read_u32(np, "fsl,settling-time", &priv->settling_time);
> > + of_property_read_u32(np, "fsl,pen-debounce", &priv->pen_debounce);
> > +
> > + return 0;
> > +}
> > +
> > +static int mx25_tcq_open(struct input_dev *idev)
> > +{
> > + struct device *dev = &idev->dev;
> > + struct mx25_tcq_priv *priv = dev_get_drvdata(dev);
> > + int ret;
> > +
> > + ret = clk_prepare_enable(priv->clk);
> > + if (ret) {
> > + dev_err(dev, "Failed to enable ipg clock\n");
> > + return ret;
> > + }
> > +
> > + ret = mx25_tcq_init(priv);
> > + if (ret) {
> > + dev_err(dev, "Failed to init tcq\n");
> > + clk_disable_unprepare(priv->clk);
> > + return ret;
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +static void mx25_tcq_close(struct input_dev *idev)
> > +{
> > + struct mx25_tcq_priv *priv = input_get_drvdata(idev);
> > +
> > + mx25_tcq_force_queue_stop(priv);
> > + mx25_tcq_disable_touch_irq(priv);
> > + mx25_tcq_disable_fifo_irq(priv);
> > + clk_disable_unprepare(priv->clk);
> > +}
> > +
> > +static int mx25_tcq_probe(struct platform_device *pdev)
> > +{
> > + struct device *dev = &pdev->dev;
> > + struct input_dev *idev;
> > + struct mx25_tcq_priv *priv;
> > + struct mx25_tsadc *tsadc = dev_get_drvdata(pdev->dev.parent);
> > + struct resource *res;
> > + void __iomem *mem;
> > + int ret;
>
> Personal preference: can we call variables that hold error codes and not
> returned in success path (i.e. when we do explicit "return 0:' for
> success) be called "error"?
Yes that's fine for me, changed it for most functions in this driver.
> > +
> > + priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
> > + if (!priv)
> > + return -ENOMEM;
> > +
> > + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> > + mem = devm_ioremap_resource(dev, res);
> > + if (!mem)
>
> devm_ioremap_resource() returns ERR_PTR-encoded pointer, you should not
> test it for NULL bit rather for IS_ERR.
Fixed, thanks.
>
> > + return -ENOMEM;
> > +
> > + ret = mx25_tcq_parse_dt(pdev, priv);
> > + if (ret)
> > + return ret;
> > +
> > + priv->regs = devm_regmap_init_mmio(dev, mem, &mx25_tcq_regconfig);
> > + if (IS_ERR(priv->regs)) {
> > + dev_err(dev, "Failed to initialize regmap\n");
> > + return PTR_ERR(priv->regs);
> > + }
> > +
> > + priv->irq = platform_get_irq(pdev, 0);
> > + if (priv->irq <= 0) {
> > + dev_err(dev, "Failed to get IRQ\n");
> > + return priv->irq;
> > + }
> > +
> > + idev = devm_input_allocate_device(dev);
> > + if (!idev) {
> > + dev_err(dev, "Failed to allocate input device\n");
> > + return -ENOMEM;
> > + }
> > +
> > + idev->name = mx25_tcq_name;
> > + idev->evbit[0] = BIT_MASK(EV_KEY) | BIT_MASK(EV_ABS);
> > + idev->keybit[BIT_WORD(BTN_TOUCH)] = BIT_MASK(BTN_TOUCH);
>
> Replace the 2 lines above with:
>
> input_set_capability(idev, EV_BTN_TOUCH);
I assume you meant
input_set_capability(idev, EV_KEY, BTN_TOUCH);
and changed it to that.
>
> > + input_set_abs_params(idev, ABS_X, 0, 0xfff, 0, 0);
> > + input_set_abs_params(idev, ABS_Y, 0, 0xfff, 0, 0);
> > +
> > + idev->id.bustype = BUS_HOST;
> > + idev->open = mx25_tcq_open;
> > + idev->close = mx25_tcq_close;
> > +
> > + priv->idev = idev;
> > + input_set_drvdata(idev, priv);
> > +
> > + priv->core_regs = tsadc->regs;
> > + if (!priv->core_regs)
> > + return -EINVAL;
> > +
> > + priv->clk = tsadc->clk;
> > + if (!priv->clk)
> > + return -EINVAL;
> > +
> > + platform_set_drvdata(pdev, priv);
> > +
> > + ret = input_register_device(idev);
> > + if (ret) {
> > + dev_err(dev, "Failed to register input device\n");
> > + return ret;
> > + }
> > +
> > + ret = devm_request_threaded_irq(dev, priv->irq, mx25_tcq_irq,
> > + mx25_tcq_irq_thread, IRQF_ONESHOT,
> > + pdev->name, priv);
> > + if (ret) {
> > + dev_err(dev, "Failed requesting IRQ\n");
> > + return ret;
> > + }
>
> Is it possible that we enable interrupt generation in the controller (in
> mx25_tcq_open) before we request IRQ and then (if someone touches the
> screen) we'll get a spurious IRQ? I'd rather we swapped
> devm_request_threaded_irq() and input_register_device(): it is perfectly
> safe to use (send events) to allocated but not registered input device.
Ok, if it is safe to send events for an allocated device I can't see why the
irq request shouldn't be first. I swapped these.
Thanks,
Markus
--
Pengutronix e.K. | |
Industrial Linux Solutions | http://www.pengutronix.de/ |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
signature.asc
Description: This is a digitally signed message part.
