> Try attached patch, I hadn't noticed the segment counts were wrong
> because I have implicit recounting.
Yes, this patch fixes the problem, thanks. Once I aplied I could mount the
cd and write a file to it, so it seems to work.
Three semi-related comments.
The udf from cvs tree has annoying habbit to put udf.o in /fs/udf.o dir
while new modutils put udf.o in kernel/fs/udf/udf.o so if you are not
carefull you still will load old udf.o driver, evern after unning 'make
install' from udf cvs tree.
So when using packet mode with udf I get just 450mb out of 650mb cd?
pktcdvd reports the read speed as 6x, shouldn't it be 8x as this is 8432
drive.
Just for kicks I have attached output of dmesg while using the cd-rw to
mount and write in block mode on udf filesystem.
Thanks for great work! I finally should be able to use cd-rw in packet
mode!
--
Adam
http://www.eax.com The Supreme Headquarters of the 32 bit registers
Linux version 2.4.0-test7-packet (root@pepsi) (gcc version egcs-2.91.66 19990314/Linux
(egcs-1.1.2 release)) #24 SMP Fri Sep 8 20:26:35 EDT 2000
BIOS-provided physical RAM map:
BIOS-e820: 000000000009fc00 @ 0000000000000000 (usable)
BIOS-e820: 0000000000000400 @ 000000000009fc00 (usable)
BIOS-e820: 0000000000010000 @ 00000000000f0000 (reserved)
BIOS-e820: 0000000000001000 @ 00000000fec00000 (reserved)
BIOS-e820: 0000000000001000 @ 00000000fee00000 (reserved)
BIOS-e820: 0000000000010000 @ 00000000ffff0000 (reserved)
BIOS-e820: 000000000bef0000 @ 0000000000100000 (usable)
BIOS-e820: 000000000000d000 @ 000000000bff3000 (ACPI data)
BIOS-e820: 0000000000003000 @ 000000000bff0000 (ACPI NVS)
Scan SMP from c0000000 for 1024 bytes.
Scan SMP from c009fc00 for 1024 bytes.
Scan SMP from c00f0000 for 65536 bytes.
found SMP MP-table at 000f5ae0
hm, page 000f5000 reserved twice.
hm, page 000f6000 reserved twice.
hm, page 000f1000 reserved twice.
hm, page 000f2000 reserved twice.
On node 0 totalpages: 49136
zone(0): 4096 pages.
zone(1): 45040 pages.
zone(2): 0 pages.
Intel MultiProcessor Specification v1.4
Virtual Wire compatibility mode.
OEM ID: OEM00000 Product ID: PROD00000000 APIC at: 0xFEE00000
Processor #0 Pentium(tm) Pro APIC version 17
Floating point unit present.
Machine Exception supported.
64 bit compare & exchange supported.
Internal APIC present.
Bootup CPU
Processor #1 Pentium(tm) Pro APIC version 17
Floating point unit present.
Machine Exception supported.
64 bit compare & exchange supported.
Internal APIC present.
Bus #0 is PCI
Bus #1 is PCI
Bus #2 is ISA
I/O APIC #2 Version 17 at 0xFEC00000.
Int: type 3, pol 0, trig 0, bus 2, IRQ 00, APIC ID 2, APIC INT 00
Int: type 0, pol 0, trig 0, bus 2, IRQ 01, APIC ID 2, APIC INT 01
Int: type 0, pol 0, trig 0, bus 2, IRQ 00, APIC ID 2, APIC INT 02
Int: type 0, pol 0, trig 0, bus 2, IRQ 03, APIC ID 2, APIC INT 03
Int: type 0, pol 0, trig 0, bus 2, IRQ 04, APIC ID 2, APIC INT 04
Int: type 0, pol 0, trig 0, bus 2, IRQ 05, APIC ID 2, APIC INT 05
Int: type 0, pol 0, trig 0, bus 2, IRQ 06, APIC ID 2, APIC INT 06
Int: type 0, pol 0, trig 0, bus 2, IRQ 07, APIC ID 2, APIC INT 07
Int: type 0, pol 1, trig 1, bus 2, IRQ 08, APIC ID 2, APIC INT 08
Int: type 0, pol 0, trig 0, bus 2, IRQ 0d, APIC ID 2, APIC INT 0d
Int: type 0, pol 0, trig 0, bus 2, IRQ 0e, APIC ID 2, APIC INT 0e
Int: type 0, pol 0, trig 0, bus 2, IRQ 0f, APIC ID 2, APIC INT 0f
Int: type 0, pol 3, trig 3, bus 0, IRQ 1f, APIC ID 2, APIC INT 13
Int: type 0, pol 3, trig 3, bus 0, IRQ 24, APIC ID 2, APIC INT 13
Int: type 0, pol 3, trig 3, bus 0, IRQ 34, APIC ID 2, APIC INT 11
Int: type 0, pol 3, trig 3, bus 0, IRQ 3c, APIC ID 2, APIC INT 10
Int: type 0, pol 3, trig 3, bus 0, IRQ 4c, APIC ID 2, APIC INT 12
Int: type 0, pol 3, trig 3, bus 0, IRQ 4d, APIC ID 2, APIC INT 12
Int: type 0, pol 3, trig 3, bus 1, IRQ 00, APIC ID 2, APIC INT 10
Int: type 2, pol 0, trig 0, bus 2, IRQ 00, APIC ID 2, APIC INT 17
Lint: type 3, pol 0, trig 0, bus 0, IRQ 00, APIC ID ff, APIC LINT 00
Lint: type 1, pol 0, trig 0, bus 0, IRQ 00, APIC ID ff, APIC LINT 01
Processors: 2
mapped APIC to ffffe000 (fee00000)
mapped IOAPIC to ffffd000 (fec00000)
Kernel command line: BOOT_IMAGE=packet ro root=2103 ip=off video=matrox:off
video=vga16:off hdc=ide-scsi console=ttyS0,9600 console=tty0 single
ide_setup: hdc=ide-scsi
Initializing CPU#0
Detected 551262798 Hz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 1101.00 BogoMIPS
Memory: 190908k/196544k available (1482k kernel code, 5248k reserved, 118k data, 216k
init, 0k highmem)
Dentry-cache hash table entries: 32768 (order: 6, 262144 bytes)
Buffer-cache hash table entries: 8192 (order: 3, 32768 bytes)
Page-cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 16384 (order: 5, 131072 bytes)
Checking 386/387 coupling... OK, FPU using exception 16 error reporting.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.36 (20000221) Richard Gooch ([EMAIL PROTECTED])
CPU0: Intel Celeron (Mendocino) stepping 05
per-CPU timeslice cutoff: 356.82 usecs.
Getting VERSION: 40011
Getting VERSION: 40011
Getting ID: 0
Getting ID: f000000
Getting LVT0: 700
Getting LVT1: 400
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
CPU present map: 3
Booting processor 1/1 eip 2000
Setting warm reset code and vector.
1.
2.
3.
Asserting INIT.
Waiting for send to finish...
+Deasserting INIT.
Waiting for send to finish...
+#startup loops: 2.
Sending STARTUP #1.
After apic_write.
Startup point 1.
Initializing CPU#1
Waiting for send to finish...
CPU#1 (phys ID: 1) waiting for CALLOUT
+Sending STARTUP #2.
After apic_write.
Startup point 1.
Waiting for send to finish...
+After Startup.
Before Callout 1.
After Callout 1.
CALLIN, before setup_local_APIC().
masked ExtINT on CPU#1
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Calibrating delay loop... 1101.00 BogoMIPS
Stack at about cbfe7fbc
OK.
CPU1: Intel Celeron (Mendocino) stepping 05
CPU has booted.
Before bogomips.
Total of 2 processors activated (2202.01 BogoMIPS).
Before bogocount - setting activated=1.
Boot done.
ENABLING IO-APIC IRQs
...changing IO-APIC physical APIC ID to 2 ... ok.
Synchronizing Arb IDs.
init IO_APIC IRQs
IO-APIC (apicid-pin) 2-0, 2-9, 2-10, 2-11, 2-12, 2-20, 2-21, 2-22, 2-23 not
connected.
..TIMER: vector=49 pin1=2 pin2=0
activating NMI Watchdog ... done.
number of MP IRQ sources: 20.
number of IO-APIC #2 registers: 24.
testing the IO APIC.......................
IO APIC #2......
.... register #00: 02000000
....... : physical APIC id: 02
.... register #01: 00170011
....... : max redirection entries: 0017
....... : IO APIC version: 0011
.... register #02: 00000000
....... : arbitration: 00
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 003 03 0 0 0 0 0 1 1 39
02 003 03 0 0 0 0 0 1 1 31
03 003 03 0 0 0 0 0 1 1 41
04 003 03 0 0 0 0 0 1 1 49
05 003 03 0 0 0 0 0 1 1 51
06 003 03 0 0 0 0 0 1 1 59
07 003 03 0 0 0 0 0 1 1 61
08 003 03 0 0 0 0 0 1 1 69
09 000 00 1 0 0 0 0 0 0 00
0a 000 00 1 0 0 0 0 0 0 00
0b 000 00 1 0 0 0 0 0 0 00
0c 000 00 1 0 0 0 0 0 0 00
0d 000 00 1 0 0 0 0 0 0 00
0e 003 03 0 0 0 0 0 1 1 71
0f 003 03 0 0 0 0 0 1 1 79
10 003 03 1 1 0 1 0 1 1 81
11 003 03 1 1 0 1 0 1 1 89
12 003 03 1 1 0 1 0 1 1 91
13 003 03 1 1 0 1 0 1 1 99
14 000 00 1 0 0 0 0 0 0 00
15 000 00 1 0 0 0 0 0 0 00
16 000 00 1 0 0 0 0 0 0 00
17 000 00 1 0 0 0 0 0 0 00
IRQ to pin mappings:
IRQ0 -> 2
IRQ1 -> 1
IRQ3 -> 3
IRQ4 -> 4
IRQ5 -> 5
IRQ6 -> 6
IRQ7 -> 7
IRQ8 -> 8
IRQ13 -> 13
IRQ14 -> 14
IRQ15 -> 15
IRQ16 -> 16
IRQ17 -> 17
IRQ18 -> 18
IRQ19 -> 19
.................................... done.
calibrating APIC timer ...
..... CPU clock speed is 551.2151 MHz.
..... host bus clock speed is 100.2208 MHz.
cpu: 0, clocks: 1002208, slice: 334069
CPU0<T0:1002208,T1:668128,D:11,S:334069,C:1002208>
cpu: 1, clocks: 1002208, slice: 334069
CPU1<T0:1002208,T1:334064,D:6,S:334069,C:1002208>
checking TSC synchronization across CPUs: passed.
Setting commenced=1, go go go
mtrr: your CPUs had inconsistent fixed MTRR settings
mtrr: probably your BIOS does not setup all CPUs
PCI: PCI BIOS revision 2.10 entry at 0xfb5c0, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Using IRQ router PIIX [8086/7000] at 00:07.0
PCI->APIC IRQ transform: (B0,I7,P3) -> 19
PCI->APIC IRQ transform: (B0,I9,P0) -> 19
PCI->APIC IRQ transform: (B0,I13,P0) -> 17
PCI->APIC IRQ transform: (B0,I15,P0) -> 16
PCI->APIC IRQ transform: (B0,I19,P0) -> 18
PCI->APIC IRQ transform: (B0,I19,P1) -> 18
PCI->APIC IRQ transform: (B1,I0,P0) -> 16
Limiting direct PCI/PCI transfers.
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
IEEE 802.2 LLC for Linux 2.1 (c) 1996 Tim Alpaerts
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 1024 buckets, 8Kbytes
TCP: Hash tables configured (established 16384 bind 16384)
IPv4 over IPv4 tunneling driver
early initialization of device tunl0 is deferred
GRE over IPv4 tunneling driver
early initialization of device gre0 is deferred
Linux IP multicast router 0.06 plus PIM-SM
Initializing RT netlink socket
Starting kswapd v1.7
Detected PS/2 Mouse Port.
pty: 256 Unix98 ptys configured
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PIIX4: IDE controller on PCI bus 00 dev 39
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA
HPT366: onboard version of chipset, pin1=1 pin2=2
HPT366: IDE controller on PCI bus 00 dev 98
HPT366: chipset revision 1
HPT366: not 100% native mode: will probe irqs later
ide2: BM-DMA at 0xd400-0xd407, BIOS settings: hde:DMA, hdf:pio
HPT366: IDE controller on PCI bus 00 dev 99
HPT366: chipset revision 1
HPT366: not 100% native mode: will probe irqs later
ide3: BM-DMA at 0xe000-0xe007, BIOS settings: hdg:pio, hdh:pio
hda: IBM-DHEA-38451, ATA DISK drive
hdc: QPS CD-R PX-W8432T, ATAPI CDROM drive
hdd: CD-532E, ATAPI CDROM drive
hde: WDC WD272AA, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
ide2 at 0xcc00-0xcc07,0xd002 on irq 18
hda: 16514064 sectors (8455 MB) w/472KiB Cache, CHS=1027/255/63, UDMA(33)
hde: 53128656 sectors (27202 MB) w/2048KiB Cache, CHS=52707/16/63, UDMA(66)
Partition check:
hda: hda1
hde: hde1 hde2 hde3
Serial driver version 5.02 (2000-08-09) with MANY_PORTS SHARE_IRQ DETECT_IRQ
SERIAL_PCI enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
Real Time Clock Driver v1.10c
Non-volatile memory driver v1.1
Linux PCMCIA Card Services 3.1.11
options: [pci] [cardbus] [pm]
ip_conntrack (1535 buckets, 12280 max)
ACPI: support found
ip_tables: (c)2000 Netfilter core team
ACPI: namespace load failed
ACPI: -0550: <7>ACPI: *** Success: Entire namespace and objects deleted
ds: no socket drivers loaded!
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 216k freed
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
Adding Swap: 131536k swap-space (priority -1)
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
scsi : 1 host.
Vendor: QPS Model: CD-R PX-W8432T Rev: 1.05
Type: CD-ROM ANSI SCSI revision: 02
Vendor: TEAC Model: CD-532E Rev: 3.0A
Type: CD-ROM ANSI SCSI revision: 02
udf: registering filesystem
pktcdvd: v0.0.2c 08/09/2000 Jens Axboe ([EMAIL PROTECTED])
Detected scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
Detected scsi CD-ROM sr1 at scsi0, channel 0, id 1, lun 0
sr0: scsi3-mmc drive: 32x/32x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.11
sr1: scsi3-mmc drive: 32x/32x xa/form2 cdda tray
VFS: Disk change detected on device sr(11,0)
pktcdvd: writer sr0 sucessfully registered
pktcdvd: 454208KB available on disc
pktcdvd: inserted media is CD-RW
pktcdvd: Fixed packets, 32 blocks / packet, Mode-1 disc
pktcdvd: speed (R/W) 6/4
pktcdvd: 454208KB available on disc
UDF-fs DEBUG (../linux-2.4/lowlevel.c, 65): udf_get_last_session: CDROMMULTISESSION
not supported: rc=-22
UDF-fs DEBUG (../linux-2.4/super.c, 1355): udf_read_super: Multi-session=0
UDF-fs DEBUG (../linux-2.4/super.c, 1364): udf_read_super: Lastblock=227103
UDF-fs DEBUG (../linux-2.4/super.c, 392): udf_vrs: Starting at sector 16 (2048 byte
sectors)
UDF-fs DEBUG (../linux-2.4/super.c, 742): udf_load_pvoldesc: recording time
968452905/179539, 2000/09/08 17:41 (1ed4)
UDF-fs DEBUG (../linux-2.4/super.c, 928): udf_load_logicalvol: Partition (0:0) type 2
on volume 1
UDF-fs DEBUG (../linux-2.4/super.c, 938): udf_load_logicalvol: FileSet found in
LogicalVolDesc at block=32, partition=0
UDF-fs DEBUG (../linux-2.4/super.c, 789): udf_load_partdesc: Searching map: (0 == 0)
UDF-fs DEBUG (../linux-2.4/super.c, 823): udf_load_partdesc: unallocatedSpaceBitmap
(part 0) @ 0
UDF-fs DEBUG (../linux-2.4/super.c, 860): udf_load_partdesc: Partition (0:0 type 1522)
starts at physical 2464, block length 224352
UDF-fs DEBUG (../linux-2.4/super.c, 1177): udf_load_partition: Using anchor in block
227103
UDF-fs DEBUG (../linux-2.4/super.c, 714): udf_find_fileset: Fileset at block=32,
partition=0
UDF-fs DEBUG (../linux-2.4/super.c, 775): udf_load_fileset: Rootdir at block=64,
partition=0
UDF-fs INFO UDF 0.9.3-cvs-rw (2000/06/17) Mounting volume '', timestamp 2000/09/08
17:41 (1ed4)
pktcdvd: 454208KB available on disc
pktcdvd: inserted media is CD-RW
pktcdvd: Fixed packets, 32 blocks / packet, Mode-1 disc
pktcdvd: speed (R/W) 6/4
pktcdvd: 454208KB available on disc
UDF-fs DEBUG (../linux-2.4/lowlevel.c, 65): udf_get_last_session: CDROMMULTISESSION
not supported: rc=-22
UDF-fs DEBUG (../linux-2.4/super.c, 1355): udf_read_super: Multi-session=0
UDF-fs DEBUG (../linux-2.4/super.c, 1364): udf_read_super: Lastblock=227103
UDF-fs DEBUG (../linux-2.4/super.c, 392): udf_vrs: Starting at sector 16 (2048 byte
sectors)
UDF-fs DEBUG (../linux-2.4/super.c, 742): udf_load_pvoldesc: recording time
968452905/179539, 2000/09/08 17:41 (1ed4)
UDF-fs DEBUG (../linux-2.4/super.c, 928): udf_load_logicalvol: Partition (0:0) type 2
on volume 1
UDF-fs DEBUG (../linux-2.4/super.c, 938): udf_load_logicalvol: FileSet found in
LogicalVolDesc at block=32, partition=0
UDF-fs DEBUG (../linux-2.4/super.c, 789): udf_load_partdesc: Searching map: (0 == 0)
UDF-fs DEBUG (../linux-2.4/super.c, 823): udf_load_partdesc: unallocatedSpaceBitmap
(part 0) @ 0
UDF-fs DEBUG (../linux-2.4/super.c, 860): udf_load_partdesc: Partition (0:0 type 1522)
starts at physical 2464, block length 224352
UDF-fs DEBUG (../linux-2.4/super.c, 1177): udf_load_partition: Using anchor in block
227103
UDF-fs DEBUG (../linux-2.4/super.c, 714): udf_find_fileset: Fileset at block=32,
partition=0
UDF-fs DEBUG (../linux-2.4/super.c, 775): udf_load_fileset: Rootdir at block=64,
partition=0
UDF-fs INFO UDF 0.9.3-cvs-rw (2000/06/17) Mounting volume '', timestamp 2000/09/08
17:41 (1ed4)
Linux Tulip driver version 0.9.9 (August 11, 2000)
eth0: Lite-On 82c168 PNIC rev 32 at 0xc800, 00:A0:CC:62:2B:2A, IRQ 16.
eth0: MII transceiver #1 config 3000 status 7829 advertising 01e1.
pktcdvd: 454208KB available on disc
pktcdvd: inserted media is CD-RW
pktcdvd: Fixed packets, 32 blocks / packet, Mode-1 disc
pktcdvd: speed (R/W) 6/4
pktcdvd: 454208KB available on disc
UDF-fs DEBUG (../linux-2.4/lowlevel.c, 65): udf_get_last_session: CDROMMULTISESSION
not supported: rc=-22
UDF-fs DEBUG (../linux-2.4/super.c, 1355): udf_read_super: Multi-session=0
UDF-fs DEBUG (../linux-2.4/super.c, 1364): udf_read_super: Lastblock=227103
UDF-fs DEBUG (../linux-2.4/super.c, 392): udf_vrs: Starting at sector 16 (2048 byte
sectors)
UDF-fs DEBUG (../linux-2.4/super.c, 742): udf_load_pvoldesc: recording time
968452905/179539, 2000/09/08 17:41 (1ed4)
UDF-fs DEBUG (../linux-2.4/super.c, 928): udf_load_logicalvol: Partition (0:0) type 2
on volume 1
UDF-fs DEBUG (../linux-2.4/super.c, 938): udf_load_logicalvol: FileSet found in
LogicalVolDesc at block=32, partition=0
UDF-fs DEBUG (../linux-2.4/super.c, 789): udf_load_partdesc: Searching map: (0 == 0)
UDF-fs DEBUG (../linux-2.4/super.c, 823): udf_load_partdesc: unallocatedSpaceBitmap
(part 0) @ 0
UDF-fs DEBUG (../linux-2.4/super.c, 860): udf_load_partdesc: Partition (0:0 type 1522)
starts at physical 2464, block length 224352
UDF-fs DEBUG (../linux-2.4/super.c, 1177): udf_load_partition: Using anchor in block
227103
UDF-fs DEBUG (../linux-2.4/super.c, 714): udf_find_fileset: Fileset at block=32,
partition=0
UDF-fs DEBUG (../linux-2.4/super.c, 775): udf_load_fileset: Rootdir at block=64,
partition=0
UDF-fs INFO UDF 0.9.3-cvs-rw (2000/06/17) Mounting volume '', timestamp 2000/09/08
17:41 (1ed4)
eth0: Setting full-duplex based on MII#1 link partner capability of 41e1.
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
parport0: cpp_daisy: aa5500ff(38)
parport0: assign_addrs: aa5500ff(38)
parport0: cpp_daisy: aa5500ff(38)
parport0: assign_addrs: aa5500ff(38)
lp0: using parport0 (interrupt-driven).
lp0: console ready
Linux video capture interface: v1.00
i2c-core.o: i2c core module
i2c-algo-bit.o: i2c bit algorithm module
bttv: driver version 0.7.41 loaded
bttv: using 2 buffers with 2080k (4160k total) for capture
bttv: Bt8xx card found (0).
bttv0: Bt848 (rev 18) at 00:0d.0, irq: 17, latency: 32, memory: 0xda001000
bttv0: model: BT848A(Phoebe Tv Master + FM) [insmod option]
bttv0: gpio config override: mask=0xffffffff,
mux=0x2,0xffffffff,0xffffffff,0xffffffff,0xffffffff
i2c-algo-bit.o: Adapter: bt848 #0 scl: 1 sda: 1 -- testing...
i2c-algo-bit.o:1 scl: 1 sda: 0
i2c-algo-bit.o:2 scl: 1 sda: 1
i2c-algo-bit.o:3 scl: 0 sda: 1
i2c-algo-bit.o:4 scl: 1 sda: 1
i2c-algo-bit.o: bt848 #0 passed test.
i2c-core.o: adapter bt848 #0 registered as adapter 0.
bttv0: i2c: checking for MSP34xx @ 0x80... not found
tvaudio: TV audio decoder + audio/video mux driver
tvaudio: known chips: tda9840,tda9873h,tda9850,tda9855,tea6300,tda8425,pic16c54
(PV951)
i2c-core.o: driver generic i2c audio driver registered.
bttv0: i2c: checking for TDA9875 @ 0xb0... not found
i2c-core.o: driver i2c TV tuner driver registered.
tuner: chip found @ 0x60
bttv0: i2c attach [Temic NTSC]
i2c-core.o: client [Temic NTSC] registered to adapter [bt848 #0](pos. 0).
mice: PS/2 mouse device common for all mice
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.237 $ time 18:15:52 Sep 8 2000
usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: USB UHCI at I/O 0xc000, IRQ 19
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
usb.c: USB new device connect, assigned device number 1
hub.c: USB hub found
hub.c: 2 ports detected
usb.c: USB new device connect, assigned device number 2
usb.c: USB device 2 (prod/vend 0x45e/0x29) is not claimed by any active driver.
usb.c: registered new driver hid
usb-uhci.c: interrupt, status 3, frame# 1693
mouse0: PS/2 mouse device for input0
input0: USB HID v1.00 Mouse [Microsoft Microsoft IntelliMouse® Optical] on usb1:2.0
es1370: version v0.33 time 18:14:47 Sep 8 2000
es1370: found adapter at io 0xc400 irq 19
es1370: features: joystick off, line in, mic impedance 0
