Hi Jacob, On 01/05/2016 06:34 AM, Jacob Siverskog wrote: > On Tue, Jan 5, 2016 at 3:14 PM, Eric Dumazet <eric.duma...@gmail.com> wrote: >> On Tue, 2016-01-05 at 12:07 +0100, Jacob Siverskog wrote: >>> On Mon, Jan 4, 2016 at 4:25 PM, Eric Dumazet <eric.duma...@gmail.com> wrote: >>>> On Mon, 2016-01-04 at 10:10 +0100, Jacob Siverskog wrote: >>>>> On Wed, Dec 30, 2015 at 11:30 PM, Cong Wang <xiyou.wangc...@gmail.com> >>>>> wrote: >>>>>> On Wed, Dec 30, 2015 at 6:30 AM, Jacob Siverskog >>>>>> <jacob@teenage.engineering> wrote: >>>>>>> On Wed, Dec 30, 2015 at 2:26 PM, Eric Dumazet <eduma...@google.com> >>>>>>> wrote: >>>>>>>> How often can you trigger this bug ? >>>>>>> >>>>>>> Ok. I don't have a good repro to trigger it unfortunately, I've seen it >>>>>>> just a >>>>>>> few times when bringing up/down network interfaces. Does the trace >>>>>>> give any clue? >>>>>>> >>>>>> >>>>>> A little bit. You need to help people to narrow down the problem >>>>>> because there are too many places using skb->next and skb->prev. >>>>>> >>>>>> Since you mentioned it seems related to network interface flip, >>>>>> what network interfaces are you using? What's is your TC setup? >>>>>> >>>>>> Thanks. >>>>> >>>>> The system contains only one physical network interface (TI WL1837, >>>>> wl18xx module). >>>>> The state prior to the crash was as follows: >>>>> - One virtual network interface active (as STA, associated with access >>>>> point) >>>>> - Bluetooth (BLE only) active (same physical chip, co-existence, >>>>> btwilink/st_drv modules) >>>>> >>>>> Actions made around the time of the crash: >>>>> - Bluetooth disabled >>>>> - One additional virtual network interface brought up (also as STA) >>>>> >>>>> I believe the crash occurred between these two actions. I just saw >>>>> that there are some interesting events in the log prior to the crash: >>>>> kernel: Bluetooth: Unable to push skb to HCI core(-6) >>>>> kernel: (stc): proto stack 4's ->recv failed >>>>> kernel: (stc): remove_channel_from_table: id 3 >>>>> kernel: (stc): remove_channel_from_table: id 2 >>>>> kernel: (stc): remove_channel_from_table: id 4 >>>>> kernel: (stc): all chnl_ids unregistered >>>>> kernel: (stk) :ldisc_install = 0(stc): st_tty_close >>>>> >>>>> The first print is from btwilink.c. However, I can't see the >>>>> connection between Bluetooth (BLE) and UDP/IPv6 (we're not using >>>>> 6LoWPAN or anything similar). >>>>> >>>>> Thanks, Jacob >>>> >>>> Definitely these details are useful ;) >>>> >>>> Could you try : >>>> >>>> diff --git a/drivers/misc/ti-st/st_core.c b/drivers/misc/ti-st/st_core.c >>>> index 6e3af8b42cdd..0c99a74fb895 100644 >>>> --- a/drivers/misc/ti-st/st_core.c >>>> +++ b/drivers/misc/ti-st/st_core.c >>>> @@ -912,7 +912,9 @@ void st_core_exit(struct st_data_s *st_gdata) >>>> skb_queue_purge(&st_gdata->txq); >>>> skb_queue_purge(&st_gdata->tx_waitq); >>>> kfree_skb(st_gdata->rx_skb); >>>> + st_gdata->rx_skb = NULL; >>>> kfree_skb(st_gdata->tx_skb); >>>> + st_gdata->tx_skb = NULL; >>>> /* TTY ldisc cleanup */ >>>> err = tty_unregister_ldisc(N_TI_WL); >>>> if (err)
FWIW, You don't need that ti-st junk to get the WL1837 working; the WL1837 only has BT channels. Unfortunately, that's really all I can say about it; sorry. Regards, Peter Hurley