Hi,
On Tue, 2 Feb 2016 14:18:42 +0800 Shawn Guo wrote:
> On Wed, Jan 20, 2016 at 01:23:39PM +0100, Lothar Waßmann wrote:
> > The TX51-8xxx module series is a System On Module manufactured by
> > Ka-Ro electronics GmbH with the following characteristics:
> > Processor Freescale i.MX515
> > up to 800 MHz (commercial)
> > up to 600 MHz (industrial)
> > RAM 128/256MB mobile DDR-SDRAM
> > ROM 128MB NAND Flash
> > RTC DS1339 Real Time Clock
> > Power supply Single 3.1V to 5.5V
> > Size 26mm SO-DIMM
> > Temp. Range 0°C..70°C (-40°C..85°C)
> >
> > Signed-off-by: Lothar Waßmann <l...@karo-electronics.de>
> > ---
> > arch/arm/boot/dts/Makefile | 3 +-
> > arch/arm/boot/dts/imx51-tx51.dts | 749
> > +++++++++++++++++++++++++++++++++++++++
> > 2 files changed, 751 insertions(+), 1 deletion(-)
> > create mode 100644 arch/arm/boot/dts/imx51-tx51.dts
> >
> > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> > index a4a6d70..ea70f34 100644
> > --- a/arch/arm/boot/dts/Makefile
> > +++ b/arch/arm/boot/dts/Makefile
> > @@ -277,7 +277,8 @@ dtb-$(CONFIG_SOC_IMX51) += \
> > imx51-babbage.dtb \
> > imx51-digi-connectcore-jsk.dtb \
> > imx51-eukrea-mbimxsd51-baseboard.dtb \
> > - imx51-ts4800.dtb
> > + imx51-ts4800.dtb \
> > + imx51-tx51.dtb
> > dtb-$(CONFIG_SOC_IMX53) += \
> > imx53-ard.dtb \
> > imx53-m53evk.dtb \
> > diff --git a/arch/arm/boot/dts/imx51-tx51.dts
> > b/arch/arm/boot/dts/imx51-tx51.dts
> > new file mode 100644
> > index 0000000..80c5d60
> > --- /dev/null
> > +++ b/arch/arm/boot/dts/imx51-tx51.dts
> > @@ -0,0 +1,749 @@
> > +/*
> > + * Copyright 2012-2014 Lothar Waßmann <l...@karo-electronics.de>
> > + *
> > + * The code contained herein is licensed under the GNU General Public
> > + * License. You may obtain a copy of the GNU General Public License
> > + * Version 2 at the following locations:
> > + *
> > + * http://www.opensource.org/licenses/gpl-license.html
> > + * http://www.gnu.org/copyleft/gpl.html
> > + */
>
> We generally suggest GPL/X11 dual license for new dts to consider
> non-Linux device tree users.
>
OK.
> > +
> > +/dts-v1/;
> > +#include "imx51.dtsi"
> > +#include <dt-bindings/pwm/pwm.h>
> > +#include <dt-bindings/interrupt-controller/irq.h>
> > +
> > +/ {
> > + model = "Ka-Ro electronics TX51 module";
> > + compatible = "karo,tx51", "fsl,imx51";
> > +
> > + aliases {
> > + backlight = &backlight;
> > + display = &display;
> > + i2c1 = &i2c_gpio;
> > + usbotg = &usbotg;
> > + wlan0 = &wlan0;
> > + };
> > +
> > + chosen {
> > + stdout-path = &uart1;
> > + };
> > +
> > + backlight: pwm-backlight {
> > + compatible = "pwm-backlight";
> > + pwms = <&pwm1 0 500000 PWM_POLARITY_INVERTED>;
> > + power-supply = <®_3v3>;
> > + brightness-levels = <
> > + 0 1 2 3 4 5 6 7 8 9
> > + 10 11 12 13 14 15 16 17 18 19
> > + 20 21 22 23 24 25 26 27 28 29
> > + 30 31 32 33 34 35 36 37 38 39
> > + 40 41 42 43 44 45 46 47 48 49
> > + 50 51 52 53 54 55 56 57 58 59
> > + 60 61 62 63 64 65 66 67 68 69
> > + 70 71 72 73 74 75 76 77 78 79
> > + 80 81 82 83 84 85 86 87 88 89
> > + 90 91 92 93 94 95 96 97 98 99
> > + 100
> > + >;
> > + default-brightness-level = <50>;
> > + };
> > +
> > + clocks {
> > + ckih1 {
> > + clock-frequency = <0>;
> > + };
> > +
> > + mclk: clock@0 {
>
> I would like to see these fixed rate clocks are named in a consistent
> way, maybe just drop 'reg' property and use a unique clock name to align
> with what imx51.dtsi does.
>
OK.
> > + compatible = "fixed-clock";
> > + reg = <0>;
> > + #clock-cells = <0>;
> > + clock-output-names = "mclk";
> > + clock-frequency = <26000000>;
> > + };
> > +
> > + clk_26M: clock@1 {
> > + compatible = "fixed-clock";
> > + reg = <1>;
> > + #clock-cells = <0>;
> > + clock-output-names = "clk_26M";
> > + clock-frequency = <26000000>;
> > + gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
> > + };
> > +
> > + wlan_ref_clk: wlan-ref-clk {
> > + compatible = "ti,wilink-clock";
>
> I do not see this compatible string is documented anywhere. And how is
> this compatible string used by kernel?
>
This is a relic from a Test of a TI Wifi adapter.
Will be removed.
[...]
> > + regulators {
> > + compatible = "simple-bus";
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + reg_2v5: regulator@0 {
>
> Device tree maintainers do not like the fake simple-bus container node.
> We are asked to put these fixed regulators directly under root node,
> with a unique node name like:
>
> reg_xxx: regulator-xxx {
> ...
> };
>
OK.
> > + usbphy {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + compatible = "simple-bus";
> > +
> > + usbh1phy: usbphy@0 {
> > + compatible = "usb-nop-xceiv";
> > + reg = <0>;
> > + clocks = <&clk_26M>;
> > + clock-names = "main_clk";
> > + };
>
> This should probably go with the same way as fixed regulators.
>
This is modeled exactly after the code in imx51.dtsi:
| usbphy {
| #address-cells = <1>;
| #size-cells = <0>;
| compatible = "simple-bus";
|
| usbphy0: usbphy@0 {
| compatible = "usb-nop-xceiv";
| reg = <0>;
| clocks = <&clks IMX5_CLK_USB_PHY_GATE>;
| clock-names = "main_clk";
| };
| };
> > + };
> > +
> > + wlan0: tiwi-ble {
> > + compatible = "ti,wilink6";
>
> Undocumented compatible string.
>
See above.
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_wlan0>;
> > + clocks = <&wlan_ref_clk>;
> > + clock-names = "refclock";
> > + interrupt-parent = <&gpio1>;
> > + interrupts = <5 IRQ_TYPE_LEVEL_LOW>;
> > + };
> > +};
> > +
> > +&audmux {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_ssi1>;
> > + status = "okay";
> > +};
> > +
> > +&ecspi1 {
> > + fsl,spi-num-chipselects = <2>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_ecspi1>;
> > + cs-gpios = <&gpio4 24 GPIO_ACTIVE_LOW>,
> > + <&gpio4 25 GPIO_ACTIVE_LOW>;
> > + status = "okay";
> > +
> > + spidev0: spi@0 {
> > + compatible = "spidev";
> > + reg = <0>;
> > + spi-max-frequency = <54000000>;
> > + };
> > +
> > + spidev1: spi@1 {
> > + compatible = "spidev";
> > + reg = <1>;
> > + spi-max-frequency = <54000000>;
> > + };
> > +};
> > +
> > +&esdhc1 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_esdhc1>;
> > + cd-gpios = <&gpio3 8 GPIO_ACTIVE_LOW>;
> > + fsl,wp-controller;
> > + status = "okay";
> > +};
> > +
> > +&esdhc2 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_esdhc2 &pinctrl_wlan0>;
> > + vmmc-supply = <®_wlan0>;
> > + bus-width = <4>;
> > + no-1-8-v;
> > + fsl,wp-controller;
> > + cap-sdio-irq;
> > + non-removable;
> > + //cd-gpios = <&gpio3 6 GPIO_ACTIVE_LOW>;
>
> Drop it.
>
This also stems from the Wifi adapter test...
> > + status = "okay";
> > +};
> > +
> > +&fec {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_fec>;
> > + phy-mode = "mii";
> > +// phy-handle = <&phy0>;
> > + local-mac-address = [000000000000]; /* will be set by U-Boot */
> > + status = "okay";
> > +
> > + phy0: ethernet-phy@0 {
> > + interrupt-parent = <&gpio3>;
> > + interrupts = <18 0>;
> > + device_type = "ethernet-phy";
> > + };
>
> This probably works, but I think we should follow the more standard
> bindings to put it like the following?
>
>
> phy-handle = <&phy0>;
>
> mdio {
> #address-cells = <1>;
> #size-cells = <0>;
>
> phy0: ethernet-phy@0 {
> interrupt-parent = <&gpio3>;
> interrupts = <18 0>;
> device_type = "ethernet-phy";
> };
> };
>
OK.
> > +};
> > +
> > +&ipu {
> > + status = "okay";
> > +};
> > +
> > +&i2c2 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_i2c2>;
> > + status = "okay";
> > +
> > + sgtl5000: sgtl5000@0a {
>
> Use generic name like 'codec' for node might comply to DT convention
> better.
>
OK.
> > + compatible = "fsl,sgtl5000";
> > + reg = <0x0a>;
> > + clocks = <&mclk>;
> > + VDDA-supply = <®_2v5>;
> > + VDDIO-supply = <®_3v3>;
> > + };
> > +
> > + polytouch: edt-ft5x06@38 {
> > + compatible = "edt,edt-ft5x06";
> > + reg = <0x38>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_edt_ft5x06>;
> > + interrupt-parent = <&gpio1>;
> > + interrupts = <5 0>;
> > + reset-gpios = <&gpio4 15 GPIO_ACTIVE_LOW>;
> > + wake-gpios = <&gpio4 9 GPIO_ACTIVE_HIGH>;
> > + };
> > +
> > + touchscreen: tsc2007@48 {
>
> tsc2007: touchscreen@48 {
>
> > + compatible = "ti,tsc2007";
> > + reg = <0x48>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_tsc2007>;
> > + interrupt-parent = <&gpio3>;
> > + interrupts = <3 0>;
> > + gpios = <&gpio3 3 GPIO_ACTIVE_LOW>;
> > + ti,x-plate-ohms = <660>;
> > + linux,wakeup;
>
> Use the new standard 'wakeup-source' please.
>
> https://git.kernel.org/cgit/linux/kernel/git/shawnguo/linux.git/commit/?h=imx/dt&id=1c49ad21c2cae607193da4495489c751d7147df2
>
OK.
> > + };
> > +};
> > +
> > +&iomuxc {
>
> Please move the node to the bottom of the file to make the reset a bit
> easier for reading.
>
> > + imx51-tx51 {
>
> Since commit 5fcdf6a7ed95 (pinctrl: imx: Allow parsing DT without
> function nodes), this additional function container node can be saved.
>
OK.
> > + pinctrl_hog: hoggrp {
> > + fsl,pins = <
> > + MX51_PAD_GPIO1_7__GPIO1_7 0x20e0
> > /* 26MHz osc enable */
> > + >;
> > + };
> > +
> > + pinctrl_ecspi1: ecspi1grp {
> > + fsl,pins = <
> > + MX51_PAD_CSPI1_SS0__ECSPI1_SS0 0x4
> > + MX51_PAD_CSPI1_SS1__ECSPI1_SS1 0x4
> > + MX51_PAD_CSPI1_SCLK__ECSPI1_SCLK 0x5
> > + MX51_PAD_CSPI1_MOSI__ECSPI1_MOSI 0x85
> > + MX51_PAD_CSPI1_MISO__ECSPI1_MISO 0x185
> > + MX51_PAD_CSPI1_RDY__ECSPI1_RDY 0x84
> > + >;
> > + };
> > +
> > + pinctrl_edt_ft5x06: edt-ft5x056grp {
>
> I would suggest to not use any hyphen in pinctrl group node name to make
> the naming looks more consistent.
>
OK.
[...]
> > +
> > + pinctrl_kpp: kppgrp-1 {
>
> The '-1' suffix means nothing and can just be dropped.
>
OK.
[...]
> > +&ssi1 {
> > + fsl,mode = "i2s-slave";
>
> The "i2s-slave" of fsl,mode is deprecated and can be dropped.
>
OK.
Lothar Waßmann
