[1.] One line summary of the problem: sata_sil24 lockups under heavy i/o
[2.] Full description of the problem/report: I have a PCI-based sata_sil24 card. It has 4 ports. It was functioning well with two disks attached. Once I attached 2 additional disks (for a total of 4) and started heavy i/o (extending a software raid5 device) the system began locking up for a few minutes at a time. After the system recovers the disk transfer speed is reduced from UDMA/100 to UDMA/66 or UDMA/44. [3.] Keywords (i.e., modules, networking, kernel): libata sata_sil24 [4.] Kernel version (from /proc/version): Linux version 2.6.19-gentoo-r2 ([EMAIL PROTECTED]) (gcc version 4.1.1 (Gentoo 4.1.1-r3)) #1 Tue Dec 19 22:55:21 PST 2006 [5.] Most recent kernel version which did not have the bug: Unknown. [8.1.] Software (add the output of the ver_linux script here) Linux cthulhu 2.6.19-gentoo-r2 #1 Tue Dec 19 22:55:21 PST 2006 i686 AMD Athlon(tm) Processor AuthenticAMD GNU/Linux Gnu C 4.1.1 Gnu make 3.81 binutils 2.17 util-linux 2.12r mount 2.12r module-init-tools 3.2.2 e2fsprogs 1.39 Linux C Library > libc.2.4 Dynamic linker (ldd) 2.4 Procps 3.2.7 Net-tools 1.60 Kbd 1.12 Sh-utils 6.7 udev 103 Modules Loaded w83781d hwmon_vid lp usbhid 8250_pnp 8250 serial_core parport_pc pcspkr parport uhci_hcd via686a i2c_isa usbcore i2c_viapro i2c_core [8.2.] Processor information (from /proc/cpuinfo): processor : 0 vendor_id : AuthenticAMD cpu family : 6 model : 4 model name : AMD Athlon(tm) Processor stepping : 4 cpu MHz : 1410.226 cache size : 256 KB fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 1 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 mmx fxsr syscall mmxext 3dnowext 3dnow bogomips : 2822.62 [8.3.] Module information (from /proc/modules): w83781d 28008 1 - Live 0xfa367000 hwmon_vid 2240 1 w83781d, Live 0xf887d000 lp 8452 0 - Live 0xfa24c000 usbhid 32288 1 - Live 0xfa257000 8250_pnp 8704 0 - Live 0xf883b000 8250 17252 1 8250_pnp, Live 0xf8851000 serial_core 14976 1 8250, Live 0xf884c000 parport_pc 28644 1 - Live 0xfa202000 pcspkr 2240 0 - Live 0xf883f000 parport 30600 2 lp,parport_pc, Live 0xf8872000 uhci_hcd 16776 0 - Live 0xf8822000 via686a 13320 0 - Live 0xf8841000 i2c_isa 3584 2 w83781d,via686a, Live 0xf8839000 usbcore 99524 4 usbhid,uhci_hcd, Live 0xf8858000 i2c_viapro 6932 0 - Live 0xf882d000 i2c_core 15952 4 w83781d,via686a,i2c_isa,i2c_viapro, Live 0xf8828000 [8.4.] Loaded driver and hardware information (/proc/ioports, /proc/iomem) 0000-001f : dma1 0020-0021 : pic1 0040-0043 : timer0 0050-0053 : timer1 0060-006f : keyboard 0070-0077 : rtc 0080-008f : dma page reg 00a0-00a1 : pic2 00c0-00df : dma2 00f0-00ff : fpu 0170-0177 : ide1 01f0-01f7 : ide0 02f8-02ff : serial 0376-0376 : ide1 0378-037a : parport0 03c0-03df : vga+ 03c0-03df : vesafb 03f6-03f6 : ide0 03f8-03ff : serial 0778-077a : parport0 0cf8-0cff : PCI conf1 7800-783f : 0000:00:11.0 7800-7807 : ide2 7808-780f : ide3 7810-783f : PDC20265 8000-8003 : 0000:00:11.0 8400-8407 : 0000:00:11.0 8800-8803 : 0000:00:11.0 8802-8802 : ide2 9000-9007 : 0000:00:11.0 9000-9007 : ide2 9400-947f : 0000:00:0b.0 9800-980f : 0000:00:0a.0 9800-980f : sata_sil24 a000-a0ff : 0000:00:09.1 a000-a0ff : sym53c8xx a400-a4ff : 0000:00:09.0 a400-a4ff : sym53c8xx d000-d01f : 0000:00:04.3 d000-d01f : uhci_hcd d400-d41f : 0000:00:04.2 d400-d41f : uhci_hcd d800-d80f : 0000:00:04.1 d800-d807 : ide0 d808-d80f : ide1 e200-e27f : 0000:00:04.4 e400-e47f : pnp 00:12 e800-e80f : 0000:00:04.4 e800-e807 : vt596_smbus 00000000-0009efff : System RAM 0009f000-0009ffff : reserved 000a0000-000bffff : Video RAM area 000c0000-000cf3ff : Video ROM 000d0000-000d27ff : Adapter ROM 000d4000-000d47ff : Adapter ROM 000d8000-000dbfff : Adapter ROM 000f0000-000fffff : System ROM 00100000-3ffebfff : System RAM 00100000-002efefe : Kernel code 002efeff-003acf43 : Kernel data 3ffec000-3ffeefff : ACPI Tables 3ffef000-3fffefff : reserved 3ffff000-3fffffff : ACPI Non-volatile Storage 50000000-5007ffff : 0000:00:0a.0 50080000-5009ffff : 0000:00:0b.0 500a0000-500affff : 0000:00:09.0 500b0000-500bffff : 0000:00:09.1 500c0000-500cffff : 0000:00:11.0 d2000000-d201ffff : 0000:00:11.0 d2800000-d280007f : 0000:00:0b.0 d3000000-d3007fff : 0000:00:0a.0 d3000000-d3007fff : sata_sil24 d3800000-d380007f : 0000:00:0a.0 d3800000-d380007f : sata_sil24 d4000000-d4000fff : 0000:00:09.1 d4000000-d4000fff : sym53c8xx d4800000-d48000ff : 0000:00:09.1 d4800000-d48000ff : sym53c8xx d5000000-d5000fff : 0000:00:09.0 d5000000-d5000fff : sym53c8xx d5800000-d58000ff : 0000:00:09.0 d5800000-d58000ff : sym53c8xx d6000000-d7cfffff : PCI Bus #01 d6000000-d6ffffff : 0000:01:00.0 d7f00000-e3ffffff : PCI Bus #01 d7fe0000-d7ffffff : 0000:01:00.0 d8000000-dfffffff : 0000:01:00.0 d8000000-dfffffff : vesafb e4000000-e7ffffff : 0000:00:00.0 ffff0000-ffffffff : reserved [8.5.] PCI information ('lspci -vvv' as root) 00:00.0 Host bridge: VIA Technologies, Inc. VT8363/8365 [KT133/KM133] (rev 03) Subsystem: ASUSTeK Computer Inc. A7V133/A7V133-C Mainboard Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR+ Latency: 8 Region 0: Memory at e4000000 (32-bit, prefetchable) [size=64M] Capabilities: [a0] AGP version 2.0 Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4 Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none> Capabilities: [c0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:01.0 PCI bridge: VIA Technologies, Inc. VT8363/8365 [KT133/KM133 AGP] (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- Latency: 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 0000f000-00000fff Memory behind bridge: d6000000-d7cfffff Prefetchable memory behind bridge: d7f00000-e3ffffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B- Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI+ D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:04.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 40) Subsystem: ASUSTeK Computer Inc. A7V133/A7V133-C Mainboard Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Capabilities: [c0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:04.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 Region 4: I/O ports at d800 [size=16] Capabilities: [c0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:04.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 16) (prog-if 00 [UHCI]) Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32, Cache Line Size: 32 bytes Interrupt: pin D routed to IRQ 5 Region 4: I/O ports at d400 [size=32] Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:04.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 16) (prog-if 00 [UHCI]) Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32, Cache Line Size: 32 bytes Interrupt: pin D routed to IRQ 5 Region 4: I/O ports at d000 [size=32] Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:04.4 Bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 40) Subsystem: ASUSTeK Computer Inc. A7V133/A7V133-C Mainboard Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Interrupt: pin ? routed to IRQ 9 Capabilities: [68] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:09.0 SCSI storage controller: LSI Logic / Symbios Logic 53c875 (rev 14) Subsystem: LSI Logic / Symbios Logic Unknown device 1001 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 72 (4250ns min, 16000ns max), Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 5 Region 0: I/O ports at a400 [size=256] Region 1: Memory at d5800000 (32-bit, non-prefetchable) [size=256] Region 2: Memory at d5000000 (32-bit, non-prefetchable) [size=4K] [virtual] Expansion ROM at 500a0000 [disabled] [size=64K] 00:09.1 SCSI storage controller: LSI Logic / Symbios Logic 53c875 (rev 14) Subsystem: LSI Logic / Symbios Logic Unknown device 1001 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 72 (4250ns min, 16000ns max), Cache Line Size: 64 bytes Interrupt: pin B routed to IRQ 11 Region 0: I/O ports at a000 [size=256] Region 1: Memory at d4800000 (32-bit, non-prefetchable) [size=256] Region 2: Memory at d4000000 (32-bit, non-prefetchable) [size=4K] [virtual] Expansion ROM at 500b0000 [disabled] [size=64K] 00:0a.0 RAID bus controller: Silicon Image, Inc. SiI 3124 PCI-X Serial ATA Controller (rev 01) Subsystem: Silicon Image, Inc. Unknown device 6124 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping+ SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32, Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 12 Region 0: Memory at d3800000 (64-bit, non-prefetchable) [size=128] Region 2: Memory at d3000000 (64-bit, non-prefetchable) [size=32K] Region 4: I/O ports at 9800 [size=16] [virtual] Expansion ROM at 50000000 [disabled] [size=512K] Capabilities: [64] Power Management version 2 Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=1 PME- Capabilities: [40] PCI-X non-bridge device Command: DPERE- ERO+ RBC=512 OST=12 Status: Dev=ff:1f.0 64bit+ 133MHz+ SCD- USC- DC=simple DMMRBC=2048 DMOST=12 DMCRS=128 RSCEM- 266MHz- 533MHz- Capabilities: [54] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable- Address: 0000000000000000 Data: 0000 00:0b.0 Ethernet controller: 3Com Corporation 3c905B 100BaseTX [Cyclone] (rev 30) Subsystem: 3Com Corporation 3C905B Fast Etherlink XL 10/100 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (2500ns min, 2500ns max), Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 10 Region 0: I/O ports at 9400 [size=128] Region 1: Memory at d2800000 (32-bit, non-prefetchable) [size=128] [virtual] Expansion ROM at 50080000 [disabled] [size=128K] Capabilities: [dc] Power Management version 1 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:11.0 Mass storage controller: Promise Technology, Inc. PDC20265 (FastTrak100 Lite/Ultra100) (rev 02) Subsystem: Promise Technology, Inc. Ultra100 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 Interrupt: pin A routed to IRQ 10 Region 0: I/O ports at 9000 [size=8] Region 1: I/O ports at 8800 [size=4] Region 2: I/O ports at 8400 [size=8] Region 3: I/O ports at 8000 [size=4] Region 4: I/O ports at 7800 [size=64] Region 5: Memory at d2000000 (32-bit, non-prefetchable) [size=128K] Expansion ROM at 500c0000 [size=64K] Capabilities: [58] Power Management version 1 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 01:00.0 VGA compatible controller: nVidia Corporation NV34GL [Quadro FX 500/600 PCI] (rev a1) (prog-if 00 [VGA]) Subsystem: nVidia Corporation Unknown device 01ba Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 (1250ns min, 250ns max) Interrupt: pin A routed to IRQ 11 Region 0: Memory at d6000000 (32-bit, non-prefetchable) [size=16M] Region 1: Memory at d8000000 (32-bit, prefetchable) [size=128M] Expansion ROM at d7fe0000 [disabled] [size=128K] Capabilities: [60] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [44] AGP version 3.0 Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4 Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none> [8.6.] SCSI information (from /proc/scsi/scsi) Attached devices: Host: scsi0 Channel: 00 Id: 04 Lun: 00 Vendor: EXABYTE Model: VXA-2 Rev: 1003 Type: Sequential-Access ANSI SCSI revision: 02 Host: scsi2 Channel: 00 Id: 00 Lun: 00 Vendor: ATA Model: Maxtor 6V300F0 Rev: VA11 Type: Direct-Access ANSI SCSI revision: 05 Host: scsi3 Channel: 00 Id: 00 Lun: 00 Vendor: ATA Model: Maxtor 6V300F0 Rev: VA11 Type: Direct-Access ANSI SCSI revision: 05 Host: scsi4 Channel: 00 Id: 00 Lun: 00 Vendor: ATA Model: ST3300620AS Rev: 3.AA Type: Direct-Access ANSI SCSI revision: 05 Host: scsi5 Channel: 00 Id: 00 Lun: 00 Vendor: ATA Model: ST3300620AS Rev: 3.AA Type: Direct-Access ANSI SCSI revision: 05 [8.7.] Other information /proc/interrupts CPU0 0: 20507744 XT-PIC-XT timer 1: 262 XT-PIC-XT i8042 2: 0 XT-PIC-XT cascade 5: 962175 XT-PIC-XT sym53c8xx, uhci_hcd:usb1, uhci_hcd:usb2 7: 3678 XT-PIC-XT parport0 8: 2 XT-PIC-XT rtc 10: 9153035 XT-PIC-XT ide2, eth0 11: 30 XT-PIC-XT sym53c8xx 12: 1026266 XT-PIC-XT libata 14: 840214 XT-PIC-XT ide0 15: 569928 XT-PIC-XT ide1 NMI: 11264 LOC: 20506755 ERR: 234 MIS: 0 Output of dmesg: Linux version 2.6.19-gentoo-r2 ([EMAIL PROTECTED]) (gcc version 4.1.1 (Gentoo 4.1.1-r3)) #1 Tue Dec 19 22:55:21 PST 2006 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009f000 (usable) BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000003ffec000 (usable) BIOS-e820: 000000003ffec000 - 000000003ffef000 (ACPI data) BIOS-e820: 000000003ffef000 - 000000003ffff000 (reserved) BIOS-e820: 000000003ffff000 - 0000000040000000 (ACPI NVS) BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved) 127MB HIGHMEM available. 896MB LOWMEM available. Entering add_active_range(0, 0, 262124) 0 entries of 256 used Zone PFN ranges: DMA 0 -> 4096 Normal 4096 -> 229376 HighMem 229376 -> 262124 early_node_map[1] active PFN ranges 0: 0 -> 262124 On node 0 totalpages: 262124 DMA zone: 32 pages used for memmap DMA zone: 0 pages reserved DMA zone: 4064 pages, LIFO batch:0 Normal zone: 1760 pages used for memmap Normal zone: 223520 pages, LIFO batch:31 HighMem zone: 255 pages used for memmap HighMem zone: 32493 pages, LIFO batch:7 DMI 2.3 present. Allocating PCI resources starting at 50000000 (gap: 40000000:bfff0000) Detected 1410.226 MHz processor. Built 1 zonelists. Total pages: 260077 Kernel command line: root=/dev/hda3 nmi_watchdog=1 video=vesafb:ywrap,mtrr,[EMAIL PROTECTED] splash=verbose,theme:emergence console=tty1 lapic Local APIC disabled by BIOS -- reenabling. Found and enabled local APIC! mapped APIC to ffffd000 (fee00000) Enabling fast FPU save and restore... done. Initializing CPU#0 PID hash table entries: 4096 (order: 12, 16384 bytes) Console: colour VGA+ 80x25 Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 1034748k/1048496k available (1983k kernel code, 13024k reserved, 756k data, 172k init, 130992k highmem) virtual kernel memory layout: fixmap : 0xfffaf000 - 0xfffff000 ( 320 kB) pkmap : 0xff800000 - 0xffc00000 (4096 kB) vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB) lowmem : 0xc0000000 - 0xf8000000 ( 896 MB) .init : 0xc03b0000 - 0xc03db000 ( 172 kB) .data : 0xc02efeff - 0xc03acf44 ( 756 kB) .text : 0xc0100000 - 0xc02efeff (1983 kB) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay using timer specific routine.. 2822.62 BogoMIPS (lpj=14113144) Mount-cache hash table entries: 512 CPU: After generic identify, caps: 0183fbff c1c7fbff 00000000 00000000 00000000 00000000 00000000 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 256K (64 bytes/line) CPU: After all inits, caps: 0183fbff c1c7fbff 00000000 00000420 00000000 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. Compat vDSO mapped to ffffe000. CPU: AMD Athlon(tm) Processor stepping 04 Checking 'hlt' instruction... OK. checking if image is initramfs... it is Freeing initrd memory: 792k freed NET: Registered protocol family 16 PCI: PCI BIOS revision 2.10 entry at 0xf1180, last bus=1 PCI: Using configuration type 1 Setting up standard PCI resources Linux Plug and Play Support v0.97 (c) Adam Belay PnPBIOS: Scanning system for PnP BIOS support... PnPBIOS: Found PnP BIOS installation structure at 0xc00fc4f0 PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0xc520, dseg 0xf0000 PnPBIOS: 13 nodes reported by PnP BIOS; 13 recorded by driver SCSI subsystem initialized libata version 2.00 loaded. PCI: Probing PCI hardware PCI: Probing PCI hardware (bus 00) Disabling VIA memory write queue (PCI ID 0305, rev 03): [55] 89 & 1f -> 09 PCI quirk: region e200-e27f claimed by vt82c686 HW-mon PCI quirk: region e800-e80f claimed by vt82c686 SMB Boot video device is 0000:01:00.0 PCI: Using IRQ router VIA [1106/0686] at 0000:00:04.0 PCI: setting IRQ 10 as level-triggered PCI: Found IRQ 10 for device 0000:00:0b.0 PCI: Sharing IRQ 10 with 0000:00:11.0 spurious 8259A interrupt: IRQ7. PCI: BIOS reporting unknown device 00:48 PCI: Device 0000:00:09.1 not found by BIOS pnp: 00:12: ioport range 0xe400-0xe47f has been reserved pnp: 00:12: ioport range 0xe800-0xe83f could not be reserved PCI: Bridge: 0000:00:01.0 IO window: disabled. MEM window: d6000000-d7cfffff PREFETCH window: d7f00000-e3ffffff PCI: Setting latency timer of device 0000:00:01.0 to 64 NET: Registered protocol family 2 IP route cache hash table entries: 32768 (order: 5, 131072 bytes) TCP established hash table entries: 131072 (order: 7, 524288 bytes) TCP bind hash table entries: 65536 (order: 6, 262144 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered Machine check exception polling timer started. highmem bounce pool size: 64 pages Installing knfsd (copyright (C) 1996 [EMAIL PROTECTED]). io scheduler noop registered io scheduler anticipatory registered (default) Applying VIA southbridge workaround. PCI: Disabling Via external APIC routing Real Time Clock Driver v1.12ac Software Watchdog Timer: 0.07 initialized. soft_noboot=0 soft_margin=60 sec (nowayout= 0) Linux agpgart interface v0.101 (c) Dave Jones agpgart: Detected VIA Twister-K/KT133x/KM133 chipset agpgart: AGP aperture is 64M @ 0xe4000000 [drm] Initialized drm 1.0.1 20051102 Hangcheck: starting hangcheck timer 0.9.0 (tick is 180 seconds, margin is 60 seconds). Hangcheck: Using get_cycles(). vesafb: unrecognized option mtrr vesafb: NVIDIA Corporation, NV34 Board - q162-4nz, Chip Rev (OEM: NVIDIA) vesafb: VBE version: 3.0 vesafb: protected mode interface info at c000:f0c0 vesafb: pmi: set display start = c00cf0f6, set palette = c00cf160 vesafb: pmi: ports = 3b4 3b5 3ba 3c0 3c1 3c4 3c5 3c6 3c7 3c8 3c9 3cc 3ce 3cf 3d0 3d1 3d2 3d3 3d4 3d5 3da vesafb: VBIOS/hardware doesn't support DDC transfers vesafb: no monitor limits have been set vesafb: scrolling: ywrap using protected mode interface, yres_virtual=12288 Console: switching to colour frame buffer device 128x48 fbsplash: console 0 using theme 'emergence' fbsplash: switched splash state to 'on' on console 0 vesafb: framebuffer at 0xd8000000, mapped to 0xf8880000, using 24576k, total 131072k fb0: VESA VGA frame buffer device isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found PNP: PS/2 Controller [PNP0303] at 0x60,0x64 irq 1 PNP: PS/2 controller doesn't have AUX irq; using default 12 serio: i8042 KBD port at 0x60,0x64 irq 1 mice: PS/2 mouse device common for all mice RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize loop: loaded (max 8 devices) PCI: Enabling device 0000:00:0b.0 (0014 -> 0017) PCI: Found IRQ 10 for device 0000:00:0b.0 PCI: Sharing IRQ 10 with 0000:00:11.0 3c59x: Donald Becker and others. www.scyld.com/network/vortex.html 0000:00:0b.0: 3Com PCI 3c905B Cyclone 100baseTx at f8816000. Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx VP_IDE: IDE controller at PCI slot 0000:00:04.1 VP_IDE: chipset revision 6 VP_IDE: not 100% native mode: will probe irqs later VP_IDE: VIA vt82c686b (rev 40) IDE UDMA100 controller on pci0000:00:04.1 ide0: BM-DMA at 0xd800-0xd807, BIOS settings: hda:DMA, hdb:DMA ide1: BM-DMA at 0xd808-0xd80f, BIOS settings: hdc:DMA, hdd:DMA Probing IDE interface ide0... input: AT Translated Set 2 keyboard as /class/input/input0 hda: MAXTOR STM3160812A, ATA DISK drive hda: IRQ probe failed (0xfffffef8) hdb: WDC WD1600JB-00EVA0, ATA DISK drive hdb: IRQ probe failed (0xfffffef8) ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 Probing IDE interface ide1... hdc: IC35L120AVVA07-0, ATA DISK drive hdc: IRQ probe failed (0xffffbef8) hdd: WDC WD1200JB-00GVA0, ATA DISK drive hdd: IRQ probe failed (0xffffbef8) ide1 at 0x170-0x177,0x376 on irq 15 PDC20265: IDE controller at PCI slot 0000:00:11.0 PCI: Found IRQ 10 for device 0000:00:11.0 PCI: Sharing IRQ 10 with 0000:00:0b.0 PDC20265: chipset revision 2 PDC20265: ROM enabled at 0x500c0000 PDC20265: 100% native mode on irq 10 PDC20265: (U)DMA Burst Bit ENABLED Primary PCI Mode Secondary PCI Mode. ide2: BM-DMA at 0x7800-0x7807, BIOS settings: hde:DMA, hdf:pio ide3: BM-DMA at 0x7808-0x780f, BIOS settings: hdg:pio, hdh:pio Probing IDE interface ide2... hde: IC35L120AVVA07-0, ATA DISK drive ide2 at 0x9000-0x9007,0x8802 on irq 10 Probing IDE interface ide3... Probing IDE interface ide3... hda: max request size: 512KiB hda: 312581808 sectors (160041 MB) w/8192KiB Cache, CHS=19457/255/63, UDMA(100) hda: cache flushes supported hda: hda1 hda2 hda3 hda4 < hda5 hda6 > hdb: max request size: 512KiB hdb: 312581808 sectors (160041 MB) w/8192KiB Cache, CHS=19457/255/63, UDMA(100) hdb: cache flushes supported hdb: hdb1 hdc: max request size: 128KiB hdc: 241254720 sectors (123522 MB) w/1863KiB Cache, CHS=65535/16/63, UDMA(100) hdc: cache flushes supported hdc: hdc1 hdc2 hdc3 hdd: max request size: 512KiB hdd: 234441648 sectors (120034 MB) w/8192KiB Cache, CHS=16383/255/63, UDMA(100) hdd: cache flushes supported hdd: hdd1 hdd2 hdd3 hde: max request size: 128KiB hde: 241254720 sectors (123522 MB) w/1863KiB Cache, CHS=65535/16/63, UDMA(100) hde: cache flushes supported hde: hde1 hde2 hde3 PCI: setting IRQ 5 as level-triggered PCI: Found IRQ 5 for device 0000:00:09.0 PCI: Sharing IRQ 5 with 0000:00:04.2 PCI: Sharing IRQ 5 with 0000:00:04.3 sym0: <875> rev 0x14 at pci 0000:00:09.0 irq 5 sym0: Symbios NVRAM, ID 7, Fast-20, SE, parity checking sym0: open drain IRQ line driver, using on-chip SRAM sym0: using LOAD/STORE-based firmware. sym0: SCSI BUS has been reset. scsi0 : sym-2.2.3 scsi 0:0:4:0: Sequential-Access EXABYTE VXA-2 1003 PQ: 0 ANSI: 2 target0:0:4: Beginning Domain Validation target0:0:4: asynchronous target0:0:4: wide asynchronous target0:0:4: FAST-20 WIDE SCSI 40.0 MB/s ST (50 ns, offset 16) target0:0:4: Domain Validation skipping write tests target0:0:4: Ending Domain Validation PCI: setting IRQ 11 as level-triggered PCI: Found IRQ 11 for device 0000:00:09.1 sym1: <875> rev 0x14 at pci 0000:00:09.1 irq 11 sym1: Symbios NVRAM, ID 7, Fast-20, SE, parity checking sym1: open drain IRQ line driver, using on-chip SRAM sym1: using LOAD/STORE-based firmware. sym1: SCSI BUS has been reset. scsi1 : sym-2.2.3 st: Version 20050830, fixed bufsize 32768, s/g segs 256 st 0:0:4:0: Attached scsi tape st0 st0: try direct i/o: yes (alignment 512 B) st 0:0:4:0: Attached scsi generic sg0 type 1 sata_sil24 0000:00:0a.0: version 0.3 PCI: setting IRQ 12 as level-triggered PCI: Found IRQ 12 for device 0000:00:0a.0 ata1: SATA max UDMA/100 cmd 0xF8830000 ctl 0x0 bmdma 0x0 irq 12 ata2: SATA max UDMA/100 cmd 0xF8832000 ctl 0x0 bmdma 0x0 irq 12 ata3: SATA max UDMA/100 cmd 0xF8834000 ctl 0x0 bmdma 0x0 irq 12 ata4: SATA max UDMA/100 cmd 0xF8836000 ctl 0x0 bmdma 0x0 irq 12 scsi2 : sata_sil24 ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata1.00: ATA-7, max UDMA/133, 586114704 sectors: LBA48 NCQ (depth 31/32) ata1.00: ata1: dev 0 multi count 0 ata1.00: configured for UDMA/100 scsi3 : sata_sil24 ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata2.00: ATA-7, max UDMA/133, 586114704 sectors: LBA48 NCQ (depth 31/32) ata2.00: ata2: dev 0 multi count 0 ata2.00: configured for UDMA/100 scsi4 : sata_sil24 ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata3.00: ATA-7, max UDMA/133, 586072368 sectors: LBA48 NCQ (depth 31/32) ata3.00: configured for UDMA/100 scsi5 : sata_sil24 ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata4.00: ATA-7, max UDMA/133, 586072368 sectors: LBA48 NCQ (depth 31/32) ata4.00: configured for UDMA/100 scsi 2:0:0:0: Direct-Access ATA Maxtor 6V300F0 VA11 PQ: 0 ANSI: 5 SCSI device sda: 586114704 512-byte hdwr sectors (300091 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: drive cache: write back SCSI device sda: 586114704 512-byte hdwr sectors (300091 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: drive cache: write back sda: sda1 sda2 sda3 sd 2:0:0:0: Attached scsi disk sda sd 2:0:0:0: Attached scsi generic sg1 type 0 scsi 3:0:0:0: Direct-Access ATA Maxtor 6V300F0 VA11 PQ: 0 ANSI: 5 SCSI device sdb: 586114704 512-byte hdwr sectors (300091 MB) sdb: Write Protect is off sdb: Mode Sense: 00 3a 00 00 SCSI device sdb: drive cache: write back SCSI device sdb: 586114704 512-byte hdwr sectors (300091 MB) sdb: Write Protect is off sdb: Mode Sense: 00 3a 00 00 SCSI device sdb: drive cache: write back sdb: sdb1 sdb2 sdb3 sd 3:0:0:0: Attached scsi disk sdb sd 3:0:0:0: Attached scsi generic sg2 type 0 scsi 4:0:0:0: Direct-Access ATA ST3300620AS 3.AA PQ: 0 ANSI: 5 SCSI device sdc: 586072368 512-byte hdwr sectors (300069 MB) sdc: Write Protect is off sdc: Mode Sense: 00 3a 00 00 SCSI device sdc: drive cache: write back SCSI device sdc: 586072368 512-byte hdwr sectors (300069 MB) sdc: Write Protect is off sdc: Mode Sense: 00 3a 00 00 SCSI device sdc: drive cache: write back sdc: sdc1 sdc2 sdc3 sd 4:0:0:0: Attached scsi disk sdc sd 4:0:0:0: Attached scsi generic sg3 type 0 scsi 5:0:0:0: Direct-Access ATA ST3300620AS 3.AA PQ: 0 ANSI: 5 SCSI device sdd: 586072368 512-byte hdwr sectors (300069 MB) sdd: Write Protect is off sdd: Mode Sense: 00 3a 00 00 SCSI device sdd: drive cache: write back SCSI device sdd: 586072368 512-byte hdwr sectors (300069 MB) sdd: Write Protect is off sdd: Mode Sense: 00 3a 00 00 SCSI device sdd: drive cache: write back sdd: sdd1 sdd2 sdd3 sd 5:0:0:0: Attached scsi disk sdd sd 5:0:0:0: Attached scsi generic sg4 type 0 md: linear personality registered for level -1 md: raid0 personality registered for level 0 md: raid1 personality registered for level 1 raid6: int32x1 492 MB/s raid6: int32x2 560 MB/s raid6: int32x4 518 MB/s raid6: int32x8 416 MB/s raid6: mmxx1 1164 MB/s raid6: mmxx2 1974 MB/s raid6: sse1x1 1060 MB/s raid6: sse1x2 1675 MB/s raid6: using algorithm sse1x2 (1675 MB/s) md: raid6 personality registered for level 6 md: raid5 personality registered for level 5 md: raid4 personality registered for level 4 raid5: measuring checksumming speed 8regs : 1910.400 MB/sec 8regs_prefetch: 1808.800 MB/sec 32regs : 1584.800 MB/sec 32regs_prefetch: 1588.000 MB/sec pII_mmx : 3846.800 MB/sec p5_mmx : 5118.400 MB/sec raid5: using function: p5_mmx (5118.400 MB/sec) device-mapper: ioctl: 4.10.0-ioctl (2006-09-14) initialised: [EMAIL PROTECTED] TCP cubic registered NET: Registered protocol family 1 NET: Registered protocol family 17 Testing NMI watchdog ... OK. Using IPI Shortcut mode md: Autodetecting RAID arrays. Time: tsc clocksource has been installed. md: invalid raid superblock magic on sdc3 md: sdc3 has invalid sb, not importing! md: invalid raid superblock magic on sdd3 md: sdd3 has invalid sb, not importing! md: autorun ... md: considering sdd2 ... md: adding sdd2 ... md: sdd1 has different UUID to sdd2 md: adding sdc2 ... md: sdc1 has different UUID to sdd2 md: sdb3 has different UUID to sdd2 md: adding sdb2 ... md: sdb1 has different UUID to sdd2 md: sda3 has different UUID to sdd2 md: adding sda2 ... md: sda1 has different UUID to sdd2 md: hde3 has different UUID to sdd2 md: hde2 has different UUID to sdd2 md: hde1 has different UUID to sdd2 md: hdd3 has different UUID to sdd2 md: hdd2 has different UUID to sdd2 md: hdd1 has different UUID to sdd2 md: hdc3 has different UUID to sdd2 md: hdc2 has different UUID to sdd2 md: hdc1 has different UUID to sdd2 md: hda6 has different UUID to sdd2 md: hda5 has different UUID to sdd2 md: created md4 md: bind<sda2> md: bind<sdb2> md: bind<sdc2> md: bind<sdd2> md: running: <sdd2><sdc2><sdb2><sda2> raid5: device sdb2 operational as raid disk 0 raid5: device sda2 operational as raid disk 1 raid5: allocated 2116kB for md4 raid5: raid level 5 set md4 active with 2 out of 2 devices, algorithm 2 RAID5 conf printout: --- rd:2 wd:2 disk 0, o:1, dev:sdb2 disk 1, o:1, dev:sda2 md4: bitmap initialized from disk: read 12/12 pages, set 0 bits, status: 0 created bitmap (187 pages) for device md4 md: considering sdd1 ... md: adding sdd1 ... md: adding sdc1 ... md: sdb3 has different UUID to sdd1 md: adding sdb1 ... md: sda3 has different UUID to sdd1 md: adding sda1 ... md: hde3 has different UUID to sdd1 md: hde2 has different UUID to sdd1 md: hde1 has different UUID to sdd1 md: hdd3 has different UUID to sdd1 md: hdd2 has different UUID to sdd1 md: hdd1 has different UUID to sdd1 md: hdc3 has different UUID to sdd1 md: hdc2 has different UUID to sdd1 md: hdc1 has different UUID to sdd1 md: hda6 has different UUID to sdd1 md: hda5 has different UUID to sdd1 md: created md3 md: bind<sda1> md: bind<sdb1> md: bind<sdc1> md: bind<sdd1> md: running: <sdd1><sdc1><sdb1><sda1> raid5: device sdd1 operational as raid disk 3 raid5: device sdc1 operational as raid disk 2 raid5: device sdb1 operational as raid disk 0 raid5: device sda1 operational as raid disk 1 raid5: allocated 4196kB for md3 raid5: raid level 5 set md3 active with 4 out of 4 devices, algorithm 2 RAID5 conf printout: --- rd:4 wd:4 disk 0, o:1, dev:sdb1 disk 1, o:1, dev:sda1 disk 2, o:1, dev:sdc1 disk 3, o:1, dev:sdd1 md3: bitmap initialized from disk: read 12/12 pages, set 0 bits, status: 0 created bitmap (187 pages) for device md3 md: considering sdb3 ... md: adding sdb3 ... md: adding sda3 ... md: hde3 has different UUID to sdb3 md: hde2 has different UUID to sdb3 md: hde1 has different UUID to sdb3 md: hdd3 has different UUID to sdb3 md: hdd2 has different UUID to sdb3 md: hdd1 has different UUID to sdb3 md: hdc3 has different UUID to sdb3 md: hdc2 has different UUID to sdb3 md: hdc1 has different UUID to sdb3 md: hda6 has different UUID to sdb3 md: hda5 has different UUID to sdb3 md: created md5 md: bind<sda3> md: bind<sdb3> md: running: <sdb3><sda3> raid5: device sdb3 operational as raid disk 0 raid5: device sda3 operational as raid disk 1 raid5: allocated 2116kB for md5 raid5: raid level 5 set md5 active with 2 out of 2 devices, algorithm 2 RAID5 conf printout: --- rd:2 wd:2 disk 0, o:1, dev:sdb3 disk 1, o:1, dev:sda3 md5: bitmap initialized from disk: read 12/12 pages, set 0 bits, status: 0 created bitmap (187 pages) for device md5 md: considering hde3 ... md: adding hde3 ... md: hde2 has different UUID to hde3 md: hde1 has different UUID to hde3 md: adding hdd3 ... md: hdd2 has different UUID to hde3 md: hdd1 has different UUID to hde3 md: adding hdc3 ... md: hdc2 has different UUID to hde3 md: hdc1 has different UUID to hde3 md: hda6 has different UUID to hde3 md: adding hda5 ... md: created md2 md: bind<hda5> md: bind<hdc3> md: bind<hdd3> md: bind<hde3> md: running: <hde3><hdd3><hdc3><hda5> raid5: device hde3 operational as raid disk 3 raid5: device hdd3 operational as raid disk 2 raid5: device hdc3 operational as raid disk 1 raid5: device hda5 operational as raid disk 0 raid5: allocated 4196kB for md2 raid5: raid level 5 set md2 active with 4 out of 4 devices, algorithm 2 RAID5 conf printout: --- rd:4 wd:4 disk 0, o:1, dev:hda5 disk 1, o:1, dev:hdc3 disk 2, o:1, dev:hdd3 disk 3, o:1, dev:hde3 md: considering hde2 ... md: adding hde2 ... md: hde1 has different UUID to hde2 md: adding hdd2 ... md: hdd1 has different UUID to hde2 md: adding hdc2 ... md: hdc1 has different UUID to hde2 md: adding hda6 ... md: created md1 md: bind<hda6> md: bind<hdc2> md: bind<hdd2> md: bind<hde2> md: running: <hde2><hdd2><hdc2><hda6> raid5: device hde2 operational as raid disk 3 raid5: device hdd2 operational as raid disk 2 raid5: device hdc2 operational as raid disk 1 raid5: device hda6 operational as raid disk 0 raid5: allocated 4196kB for md1 raid5: raid level 5 set md1 active with 4 out of 4 devices, algorithm 2 RAID5 conf printout: --- rd:4 wd:4 disk 0, o:1, dev:hda6 disk 1, o:1, dev:hdc2 disk 2, o:1, dev:hdd2 disk 3, o:1, dev:hde2 md: considering hde1 ... md: adding hde1 ... md: adding hdd1 ... md: adding hdc1 ... md: created md0 md: bind<hdc1> md: bind<hdd1> md: bind<hde1> md: running: <hde1><hdd1><hdc1> raid5: device hde1 operational as raid disk 3 raid5: device hdd1 operational as raid disk 2 raid5: device hdc1 operational as raid disk 1 raid5: allocated 4196kB for md0 raid5: raid level 5 set md0 active with 3 out of 4 devices, algorithm 2 RAID5 conf printout: --- rd:4 wd:3 disk 1, o:1, dev:hdc1 disk 2, o:1, dev:hdd1 disk 3, o:1, dev:hde1 md: ... autorun DONE. kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly. Freeing unused kernel memory: 172k freed usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub i2c_adapter i2c-9191: sensors disabled - enable with force_addr=0xe200 usbcore: registered new device driver usb USB Universal Host Controller Interface driver v3.0 PCI: Found IRQ 5 for device 0000:00:04.2 PCI: Sharing IRQ 5 with 0000:00:04.3 PCI: Sharing IRQ 5 with 0000:00:09.0 uhci_hcd 0000:00:04.2: UHCI Host Controller uhci_hcd 0000:00:04.2: new USB bus registered, assigned bus number 1 uhci_hcd 0000:00:04.2: irq 5, io base 0x0000d400 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected input: PC Speaker as /class/input/input1 PCI: Found IRQ 5 for device 0000:00:04.3 PCI: Sharing IRQ 5 with 0000:00:04.2 PCI: Sharing IRQ 5 with 0000:00:09.0 uhci_hcd 0000:00:04.3: UHCI Host Controller uhci_hcd 0000:00:04.3: new USB bus registered, assigned bus number 2 uhci_hcd 0000:00:04.3: irq 5, io base 0x0000d000 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected parport_pc: VIA 686A/8231 detected parport_pc: probing current configuration parport_pc: Current parallel port base: 0x378 parport0: PC-style at 0x378 (0x778), irq 7, using FIFO [PCSPP,TRISTATE,COMPAT,ECP] usb 1-1: new low speed USB device using uhci_hcd and address 2 parport_pc: VIA parallel port: io=0x378, irq=7 usb 1-1: configuration #1 chosen from 1 choice Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A 00:02: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A 00:03: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A usbcore: registered new interface driver hiddev hiddev96: USB HID v1.10 Device [American Power Conversion Back-UPS XS 1500 LCD FW:837.H4 .D USB FW:H4 ] on usb-0000:00:04.2-1 usbcore: registered new interface driver usbhid drivers/usb/input/hid-core.c: v2.6:USB HID core driver EXT3 FS on hda3, internal journal lp0: using parport0 (interrupt-driven). kjournald starting. Commit interval 5 seconds EXT3 FS on hda1, internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS on dm-2, internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS on dm-0, internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS on hdb1, internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS on dm-1, internal journal EXT3-fs: mounted filesystem with ordered data mode. Adding 2008116k swap on /dev/hda2. Priority:-1 extents:1 across:2008116k eth0: setting full-duplex. device eth0 entered promiscuous mode process `named' is using obsolete setsockopt SO_BSDCOMPAT fbsplash: console 1 using theme 'emergence' fbsplash: switched splash state to 'on' on console 1 fbsplash: console 2 using theme 'emergence' fbsplash: switched splash state to 'on' on console 2 fbsplash: console 3 using theme 'emergence' fbsplash: switched splash state to 'on' on console 3 fbsplash: console 4 using theme 'emergence' fbsplash: switched splash state to 'on' on console 4 fbsplash: console 5 using theme 'emergence' fbsplash: switched splash state to 'on' on console 5 fbsplash: console 6 using theme 'emergence' fbsplash: switched splash state to 'on' on console 6 fbsplash: console 7 using theme 'emergence' fbsplash: switched splash state to 'on' on console 7 fbsplash: console 8 using theme 'emergence' fbsplash: switched splash state to 'on' on console 8 fbsplash: console 9 using theme 'emergence' fbsplash: switched splash state to 'on' on console 9 fbsplash: console 10 using theme 'emergence' fbsplash: switched splash state to 'on' on console 10 NETDEV WATCHDOG: eth0: transmit timed out eth0: transmit timed out, tx_status 00 status e000. diagnostics: net 0cd8 media 8880 dma 000000a0 fifo 0000 Flags; bus-master 1, dirty 203390(14) current 203406(14) Transmit list 01bea840 vs. c1beaac0. eth0: command 0x3002 did not complete! Status=0x9000 0: @c1bea200 length 800005ea status 0c0105ea 1: @c1bea2a0 length 800005ea status 0c0105ea 2: @c1bea340 length 800005ea status 0c0105ea 3: @c1bea3e0 length 800005ea status 0c0105ea 4: @c1bea480 length 800005ea status 0c0105ea 5: @c1bea520 length 800005ea status 0c0105ea 6: @c1bea5c0 length 800005ea status 0c0105ea 7: @c1bea660 length 800005ea status 0c0105ea 8: @c1bea700 length 800005ea status 0c0105ea 9: @c1bea7a0 length 800005ea status 0c0105ea 10: @c1bea840 length 800005ea status 0c0105ea 11: @c1bea8e0 length 8000009e status 0c00009e 12: @c1bea980 length 800005ea status 8c0005ea 13: @c1beaa20 length 800005ea status 8c0005ea 14: @c1beaac0 length 800005ea status 0c0105ea 15: @c1beab60 length 800005ea status 0c0105ea eth0: Resetting the Tx ring pointer. NETDEV WATCHDOG: eth0: transmit timed out eth0: transmit timed out, tx_status 00 status e000. diagnostics: net 0cd8 media 8880 dma 000000a0 fifo 0000 Flags; bus-master 1, dirty 203434(10) current 203450(10) Transmit list 01beab60 vs. c1bea840. 0: @c1bea200 length 800005ea status 0c0005ea 1: @c1bea2a0 length 800005ea status 0c0005ea 2: @c1bea340 length 800005ea status 0c0005ea 3: @c1bea3e0 length 800005ea status 0c0005ea 4: @c1bea480 length 800005ea status 0c0005ea 5: @c1bea520 length 80000456 status 0c000456 6: @c1bea5c0 length 800005ea status 0c0005ea 7: @c1bea660 length 800005ea status 0c0005ea 8: @c1bea700 length 80000576 status 8c000576 9: @c1bea7a0 length 800001a3 status 8c0001a3 10: @c1bea840 length 800005ea status 0c0105ea 11: @c1bea8e0 length 800005ea status 0c0105ea 12: @c1bea980 length 800005ea status 0c0105ea 13: @c1beaa20 length 800005ea status 0c0105ea 14: @c1beaac0 length 800005ea status 0c0105ea 15: @c1beab60 length 800005ea status 0c0005ea eth0: Resetting the Tx ring pointer. ata2.00: exception Emask 0x0 SAct 0x7 SErr 0x0 action 0x6 frozen ata2.00: tag 0 cmd 0x60 Emask 0x4 stat 0x40 err 0x0 (timeout) ata2.00: tag 1 cmd 0x60 Emask 0x4 stat 0x40 err 0x0 (timeout) ata2.00: tag 2 cmd 0x60 Emask 0x4 stat 0x40 err 0x0 (timeout) ata2: hard resetting port ata1.00: exception Emask 0x0 SAct 0x3 SErr 0x0 action 0x6 frozen ata1.00: tag 0 cmd 0x60 Emask 0x4 stat 0x40 err 0x0 (timeout) ata1.00: tag 1 cmd 0x60 Emask 0x4 stat 0x40 err 0x0 (timeout) ata1: hard resetting port ata3.00: exception Emask 0x0 SAct 0x7 SErr 0x0 action 0x6 frozen ata3.00: tag 0 cmd 0x60 Emask 0x4 stat 0x40 err 0x0 (timeout) ata3.00: tag 1 cmd 0x60 Emask 0x4 stat 0x40 err 0x0 (timeout) ata3.00: tag 2 cmd 0x60 Emask 0x4 stat 0x40 err 0x0 (timeout) ata3: hard resetting port ata4.00: exception Emask 0x0 SAct 0x3 SErr 0x0 action 0x6 frozen ata4.00: tag 0 cmd 0x60 Emask 0x4 stat 0x40 err 0x0 (timeout) ata4.00: tag 1 cmd 0x60 Emask 0x4 stat 0x40 err 0x0 (timeout) ata4: hard resetting port ata2: softreset failed (SRST command error) ata2: follow-up softreset failed, retrying in 5 secs ata1: softreset failed (SRST command error) ata1: follow-up softreset failed, retrying in 5 secs ata3: softreset failed (SRST command error) ata3: follow-up softreset failed, retrying in 5 secs ata4: softreset failed (SRST command error) ata4: follow-up softreset failed, retrying in 5 secs ata2: hard resetting port ata1: hard resetting port ata3: hard resetting port ata4: hard resetting port ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata2.00: failed to set xfermode (err_mask=0x120) ata2.00: limiting speed to UDMA/66 ata2: failed to recover some devices, retrying in 5 secs ata1.00: failed to set xfermode (err_mask=0x120) ata1.00: limiting speed to UDMA/66 ata1: failed to recover some devices, retrying in 5 secs ata3: spurious interrupt (slot_stat 0x0 active_tag -84148995 sactive 0x7) ATA: abnormal status 0xC7 on port 0xF8834007 ATA: abnormal status 0xC7 on port 0xF8834007 ATA: abnormal status 0xC1 on port 0xF8836007 ATA: abnormal status 0xC1 on port 0xF8836007 ata3.00: configured for UDMA/100 ata3: EH complete ata4.00: configured for UDMA/100 ata4: EH complete ata2: hard resetting port ata1: hard resetting port ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata1.00: configured for UDMA/66 ata1: EH complete ata2.00: configured for UDMA/66 ata2: EH complete SCSI device sdb: 586114704 512-byte hdwr sectors (300091 MB) sdb: Write Protect is off sdb: Mode Sense: 00 3a 00 00 SCSI device sdb: drive cache: write back SCSI device sda: 586114704 512-byte hdwr sectors (300091 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: drive cache: write back SCSI device sdc: 586072368 512-byte hdwr sectors (300069 MB) sdc: Write Protect is off sdc: Mode Sense: 00 3a 00 00 SCSI device sdc: drive cache: write back SCSI device sdd: 586072368 512-byte hdwr sectors (300069 MB) sdd: Write Protect is off sdd: Mode Sense: 00 3a 00 00 SCSI device sdd: drive cache: write back SCSI device sdb: 586114704 512-byte hdwr sectors (300091 MB) sdb: Write Protect is off sdb: Mode Sense: 00 3a 00 00 SCSI device sdb: drive cache: write back NETDEV WATCHDOG: eth0: transmit timed out eth0: transmit timed out, tx_status 00 status e000. diagnostics: net 0cd8 media 8880 dma 000000a0 fifo 0000 Flags; bus-master 1, dirty 232152(8) current 232168(8) Transmit list 01beab60 vs. c1bea700. 0: @c1bea200 length 800005ea status 0c0005ea 1: @c1bea2a0 length 800005ea status 0c0005ea 2: @c1bea340 length 800005ea status 0c0005ea 3: @c1bea3e0 length 800005ea status 0c0005ea 4: @c1bea480 length 80000456 status 0c000456 5: @c1bea520 length 800005ea status 0c0005ea 6: @c1bea5c0 length 800005ea status 8c0005ea 7: @c1bea660 length 800005ea status 8c0005ea 8: @c1bea700 length 800005ea status 0c0105ea 9: @c1bea7a0 length 800005ea status 0c0105ea 10: @c1bea840 length 800005ea status 0c0105ea 11: @c1bea8e0 length 80000162 status 0c010162 12: @c1bea980 length 800005ea status 0c0105ea 13: @c1beaa20 length 800005ea status 0c0105ea 14: @c1beaac0 length 800005ea status 0c0105ea 15: @c1beab60 length 800005ea status 0c0005ea eth0: Resetting the Tx ring pointer. NETDEV WATCHDOG: eth0: transmit timed out eth0: transmit timed out, tx_status 00 status e000. diagnostics: net 0cd8 media 8880 dma 000000a0 fifo 0000 Flags; bus-master 1, dirty 232152(8) current 232168(8) Transmit list 01bea700 vs. c1bea700. 0: @c1bea200 length 800005ea status 0c0005ea 1: @c1bea2a0 length 800005ea status 0c0005ea 2: @c1bea340 length 800005ea status 0c0005ea 3: @c1bea3e0 length 800005ea status 0c0005ea 4: @c1bea480 length 80000456 status 0c000456 5: @c1bea520 length 800005ea status 0c0005ea 6: @c1bea5c0 length 800005ea status 8c0005ea 7: @c1bea660 length 800005ea status 8c0005ea 8: @c1bea700 length 800005ea status 0c0105ea 9: @c1bea7a0 length 800005ea status 0c0105ea 10: @c1bea840 length 800005ea status 0c0105ea 11: @c1bea8e0 length 80000162 status 0c010162 12: @c1bea980 length 800005ea status 0c0105ea 13: @c1beaa20 length 800005ea status 0c0105ea 14: @c1beaac0 length 800005ea status 0c0105ea 15: @c1beab60 length 800005ea status 0c0005ea eth0: Resetting the Tx ring pointer. ata2.00: exception Emask 0x0 SAct 0x7 SErr 0x0 action 0x6 frozen ata2.00: tag 0 cmd 0x60 Emask 0x4 stat 0x40 err 0x0 (timeout) ata2.00: tag 1 cmd 0x60 Emask 0x4 stat 0x40 err 0x0 (timeout) ata2.00: tag 2 cmd 0x60 Emask 0x4 stat 0x40 err 0x0 (timeout) ata2: hard resetting port ata1.00: exception Emask 0x0 SAct 0x3 SErr 0x0 action 0x6 frozen ata1.00: tag 0 cmd 0x60 Emask 0x4 stat 0x40 err 0x0 (timeout) ata1.00: tag 1 cmd 0x60 Emask 0x4 stat 0x40 err 0x0 (timeout) ata1: hard resetting port ata3.00: exception Emask 0x0 SAct 0x7 SErr 0x0 action 0x6 frozen ata3.00: tag 0 cmd 0x60 Emask 0x4 stat 0x40 err 0x0 (timeout) ata3.00: tag 1 cmd 0x60 Emask 0x4 stat 0x40 err 0x0 (timeout) ata3.00: tag 2 cmd 0x60 Emask 0x4 stat 0x40 err 0x0 (timeout) ata3: hard resetting port ata4.00: exception Emask 0x0 SAct 0x3 SErr 0x0 action 0x6 frozen ata4.00: tag 0 cmd 0x60 Emask 0x4 stat 0x40 err 0x0 (timeout) ata4.00: tag 1 cmd 0x60 Emask 0x4 stat 0x40 err 0x0 (timeout) ata4: hard resetting port ata2: softreset failed (SRST command error) ata2: follow-up softreset failed, retrying in 5 secs ata1: softreset failed (SRST command error) ata1: follow-up softreset failed, retrying in 5 secs ata3: softreset failed (SRST command error) ata3: follow-up softreset failed, retrying in 5 secs ata4: softreset failed (SRST command error) ata4: follow-up softreset failed, retrying in 5 secs ata2: hard resetting port ata1: hard resetting port ata3: hard resetting port ata4: hard resetting port ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata2.00: failed to set xfermode (err_mask=0x120) ata2.00: limiting speed to UDMA/44 ata2: failed to recover some devices, retrying in 5 secs ata1.00: failed to set xfermode (err_mask=0x120) ata1.00: limiting speed to UDMA/44 ata1: failed to recover some devices, retrying in 5 secs ata3: spurious interrupt (slot_stat 0x0 active_tag -84148995 sactive 0x7) ATA: abnormal status 0xC7 on port 0xF8834007 ATA: abnormal status 0xC7 on port 0xF8834007 ATA: abnormal status 0xC1 on port 0xF8836007 ATA: abnormal status 0xC1 on port 0xF8836007 ata3.00: configured for UDMA/100 ata3: EH complete ata4.00: configured for UDMA/100 ata4: EH complete ata2: hard resetting port ata1: hard resetting port ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata1.00: configured for UDMA/44 ata1: EH complete ata2.00: configured for UDMA/44 ata2: EH complete SCSI device sdb: 586114704 512-byte hdwr sectors (300091 MB) sdb: Write Protect is off sdb: Mode Sense: 00 3a 00 00 SCSI device sdb: drive cache: write back SCSI device sda: 586114704 512-byte hdwr sectors (300091 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: drive cache: write back SCSI device sdc: 586072368 512-byte hdwr sectors (300069 MB) sdc: Write Protect is off sdc: Mode Sense: 00 3a 00 00 SCSI device sdc: drive cache: write back SCSI device sdd: 586072368 512-byte hdwr sectors (300069 MB) sdd: Write Protect is off sdd: Mode Sense: 00 3a 00 00 SCSI device sdd: drive cache: write back SCSI device sdb: 586114704 512-byte hdwr sectors (300091 MB) sdb: Write Protect is off sdb: Mode Sense: 00 3a 00 00 SCSI device sdb: drive cache: write back -- Mark Wagner [EMAIL PROTECTED] - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [EMAIL PROTECTED] More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/