The Parrot Board is an evaluation board with an Allwinner R16 (assumed
to be close to an Allwinner A33), 4GB of eMMC, 512MB of RAM, USB host
and OTG, a WiFi/Bluetooth combo chip, a micro SD Card reader, 2
controllable buttons, an LVDS port with separated backlight and
capacitive touch panel ports, an audio/microphone jack, a camera CSI
port, 2 sets of 22 GPIOs and an accelerometer.
Signed-off-by: Quentin Schulz <quentin.sch...@free-electrons.com>
---
Patch dependencies:
- regulator: axp20x: Add support for the (external) drivebus regulator
- ARM: dts: axp22x.dtsi: Add reg_drivebus node
- ARM: dts: axp22x.dtsi: Add usb_power_supply node
- power: axp20x_usb: Add support for usb power-supply on axp22x pmics
- mfd: axp20x: Extend axp22x_volatile_ranges
- mfd: axp20x: Add axp20x-usb-power-supply for axp22x pmics
- phy-sun4i-usb: Add workaround for missing Vbus det interrupts on A31
or the micro USB port would not be powered.
v2:
- correct typos,
- chose less generic name suffix for nodes (now_parrot_r16),
- add comment for i2c childless node,
- add comment for two regulators-powered WiFi chip,
- add comment to explicit the use of some regulators,
- add usb_vbus_power-supply property in usbphy node (this adds a
dependance to an other patch),
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/sun8i-r16-parrot.dts | 356 +++++++++++++++++++++++++++++++++
2 files changed, 357 insertions(+)
create mode 100644 arch/arm/boot/dts/sun8i-r16-parrot.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 1ff5434..6c7581f 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -762,6 +762,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \
sun8i-a33-ippo-q8h-v1.2.dtb \
sun8i-a33-q8-tablet.dtb \
sun8i-a33-sinlinx-sina33.dtb \
+ sun8i-r16-parrot.dtb \
sun8i-a83t-allwinner-h8homlet-v2.dtb \
sun8i-a83t-cubietruck-plus.dtb \
sun8i-h3-orangepi-2.dtb \
diff --git a/arch/arm/boot/dts/sun8i-r16-parrot.dts
b/arch/arm/boot/dts/sun8i-r16-parrot.dts
new file mode 100644
index 0000000..cd68bfa
--- /dev/null
+++ b/arch/arm/boot/dts/sun8i-r16-parrot.dts
@@ -0,0 +1,356 @@
+/*
+ * Copyright 2016 Quentin Schulz
+ *
+ * Quentin Schulz <quentin.sch...@free-electrons.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun8i-a33.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "Allwinner Parrot EVB R16";
+ compatible = "allwinner,parrot-evb-r16", "allwinner,sun8i-a33";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pins_parrot_r16>;
+
+ led1 {
+ label = "parrot_r16:led1:usr";
+ gpio = <&pio 4 17 GPIO_ACTIVE_HIGH>; /* PE17 */
+ };
+
+ led2 {
+ label = "parrot_r16:led2:usr";
+ gpio = <&pio 4 16 GPIO_ACTIVE_HIGH>; /* PE16 */
+ };
+ };
+
+ wifi_pwrseq: wifi_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&r_pio 0 6 GPIO_ACTIVE_LOW>; /* PL06 */
+ };
+
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins_a>;
+ status = "okay";
+
+ /* An as-yet-unknown accelerometer is connected to this i2c bus. */
+};
+
+&lradc {
+ vref-supply = <®_aldo3>;
+ status = "okay";
+
+ button@0 {
+ label = "V+";
+ linux,code = <KEY_VOLUMEUP>;
+ channel = <0>;
+ voltage = <190000>;
+ };
+
+ button@1 {
+ label = "V-";
+ linux,code = <KEY_VOLUMEDOWN>;
+ channel = <0>;
+ voltage = <390000>;
+ };
+
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_parrot_r16>;
+ vmmc-supply = <®_dcdc1>;
+ cd-gpios = <&pio 3 14 GPIO_ACTIVE_LOW>; /* PD14 */
+ bus-width = <4>;
+ status = "okay";
+};
+
+/*
+ * TODO: WiFi chip needs dldo1 AND dldo2 as vmmc-supply.
+ * aldo1 is connected to VCC-IO-WIFI and thus should be vqmmc.
+ * Once two regulators can be in sync for vmmc-supply, modify this node
+ * accordingly.
+ */
+&mmc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins_a>, <&wifi_reset_pin_parrot_r16>;
+ vmmc-supply = <®_aldo1>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+};
+
+&mmc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_8bit_pins>;
+ vmmc-supply = <®_dcdc1>;
+ bus-width = <8>;
+ non-removable;
+ cap-mmc-hw-reset;
+ status = "okay";
+};
+
+&mmc2_8bit_pins {
+ allwinner,drive = <SUN4I_PINCTRL_40_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&pio {
+ mmc0_cd_pin_parrot_r16: mmc0_cd_pin@0 {
+ allwinner,pins = "PD14";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+
+ led_pins_parrot_r16: led_pins@0 {
+ allwinner,pins = "PE16", "PE17";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ usb0_id_det: usb0_id_detect_pin@0 {
+ allwinner,pins = "PD10";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+
+ usb1_vbus_pin_parrot_r16: usb1_vbus_pin@0 {
+ allwinner,pins = "PD12";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
+
+&r_pio {
+ wifi_reset_pin_parrot_r16: wifi_reset_pin@0 {
+ allwinner,pins = "PL6";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
+
+&r_rsb {
+ status = "okay";
+
+ axp22x: pmic@3a3 {
+ compatible = "x-powers,axp223";
+ reg = <0x3a3>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ drivevbus-supply = <®_vcc5v0>;
+ x-powers,drive-vbus-en;
+ };
+};
+
+#include "axp22x.dtsi"
+
+/* Used for VCC-IO, VCC-PD, VCC-USB, HPVCC, VCC-IO-BB and VCC-IO-WIFI */
+®_aldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "aldo1";
+};
+
+®_aldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <2350000>;
+ regulator-max-microvolt = <2650000>;
+ regulator-name = "vdd-dll";
+};
+
+®_aldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-pll-avcc";
+};
+
+®_dc5ldo {
+ regulator-always-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-cpus";
+};
+
+®_dcdc1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-3v0";
+};
+
+®_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-sys";
+};
+
+®_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-cpu";
+};
+
+®_dcdc5 {
+ regulator-always-on;
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-name = "vcc-dram";
+};
+
+®_dldo1 {
+ /*
+ * TODO: WiFi chip needs dldo1 AND dldo2 to be on to be powered.
+ * Remove next line once it is possible to sync two regulators.
+ */
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi";
+};
+
+®_dldo2 {
+ /*
+ * TODO: WiFi chip needs dldo1 AND dldo2 to be on to be powered.
+ * Remove next line once it is possible to sync two regulators.
+ */
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi1";
+};
+
+®_dldo3 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-3v0-csi";
+};
+
+®_drivevbus {
+ regulator-name = "usb0-vbus";
+ status = "okay";
+};
+
+®_eldo1 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-name = "vcc-1v2-hsic";
+};
+
+®_eldo2 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "dsp-vcc";
+};
+
+/* Mapped to GPIO 22 in U21 GPIOs set */
+®_eldo3 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "eldo3";
+};
+
+®_usb1_vbus {
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb1_vbus_pin_parrot_r16>;
+ gpio = <&pio 3 12 GPIO_ACTIVE_HIGH>; /* PD12 */
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_b>;
+ status = "okay";
+};
+
+&usb_otg {
+ dr_mode = "otg";
+ status = "okay";
+};
+
+&usb_power_supply {
+ status = "okay";
+};
+
+&usbphy {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb0_id_det>;
+ usb0_vbus-supply = <®_drivevbus>;
+ usb0_id_det-gpios = <&pio 3 10 GPIO_ACTIVE_HIGH>; /* PD10 */
+ usb0_vbus_power-supply = <&usb_power_supply>;
+ usb1_vbus-supply = <®_usb1_vbus>; /* USB1 VBUS is always on */
+};
--
2.5.0
