On Mon, 04 Jul 2016 10:35:57 +0900,
Rich Felker wrote:
>
> On Mon, Jul 04, 2016 at 01:46:30AM +0900, Yoshinori Sato wrote:
> > Signed-off-by: Yoshinori Sato <ys...@users.sourceforge.jp>
> > ---
> > arch/sh/boards/of-generic.c | 64
> > +++++++++++++++++++++++++++++++++++++++++++++
> > 1 file changed, 64 insertions(+)
> >
> > diff --git a/arch/sh/boards/of-generic.c b/arch/sh/boards/of-generic.c
> > index 2d3cda3..4038682 100644
> > --- a/arch/sh/boards/of-generic.c
> > +++ b/arch/sh/boards/of-generic.c
> > @@ -16,9 +16,15 @@
> > #include <linux/irqchip.h>
> > #include <linux/clk-provider.h>
> > #include <linux/memblock.h>
> > +#include <linux/sm501-regs.h>
> > #include <asm/machvec.h>
> > #include <asm/rtc.h>
> >
> > +struct model_setup {
> > + char *name;
> > + void (*fn)(void);
> > +};
> > +
> > #ifdef CONFIG_SMP
> >
> > static void dummy_smp_setup(void)
> > @@ -125,10 +131,61 @@ static void __init sh_of_time_init(void)
> > clocksource_probe();
> > }
> >
> > +#define PA_LED 0xb0000001 /* LED Control Register */
> > +#define PA_SHUTDOWN 0xb0000003 /* Shutdown Control Register */
> > +static void landisk_power_off(void)
> > +{
> > + __raw_writeb(0x01, PA_SHUTDOWN);
> > +}
> > +
> > +static void __init landisk_setup(void)
> > +{
> > + /* LED ON */
> > + __raw_writeb(__raw_readb(PA_LED) | 0x03, PA_LED);
> > + pm_power_off = landisk_power_off;
> > +}
> > +
> > +#define PA_POWOFF 0xa4000030 /* Board Power OFF control */
> > +#define PA_OUTPORT 0xa4000036 /* LED control */
> > +static void rts7751r2d_power_off(void)
> > +{
> > + __raw_writew(0x0001, PA_POWOFF);
> > +}
> > +
> > +static void __init r2dplus_setup(void)
> > +{
> > + void __iomem *sm501_reg;
> > +
> > + __raw_writew(0x0000, PA_OUTPORT);
> > + pm_power_off = rts7751r2d_power_off;
> > +
> > + /* sm501 dram configuration:
> > + * ColSizeX = 11 - External Memory Column Size: 256 words.
> > + * APX = 1 - External Memory Active to Pre-Charge Delay: 7 clocks.
> > + * RstX = 1 - External Memory Reset: Normal.
> > + * Rfsh = 1 - Local Memory Refresh to Command Delay: 12 clocks.
> > + * BwC = 1 - Local Memory Block Write Cycle Time: 2 clocks.
> > + * BwP = 1 - Local Memory Block Write to Pre-Charge Delay: 1 clock.
> > + * AP = 1 - Internal Memory Active to Pre-Charge Delay: 7 clocks.
> > + * Rst = 1 - Internal Memory Reset: Normal.
> > + * RA = 1 - Internal Memory Remain in Active State: Do not remain.
> > + */
> > +
> > + sm501_reg = (void __iomem *)0xb3e00000 + SM501_DRAM_CONTROL;
> > + writel(readl(sm501_reg) | 0x00f107c0, sm501_reg);
> > +}
> > +
> > +static const struct model_setup model_setup_table[] __initconst = {
> > + { .name = "iodata,HDL-U", .fn = landisk_setup, },
> > + { .name = "renesas,RTS7751R2D+", .fn = r2dplus_setup, },
> > + {},
> > +};
> > +
> > static void __init sh_of_setup(char **cmdline_p)
> > {
> > struct device_node *root;
> > struct device_node *cpu;
> > + const struct model_setup *setup;
> > u32 freq;
> >
> > board_time_init = sh_of_time_init;
> > @@ -145,6 +202,13 @@ static void __init sh_of_setup(char **cmdline_p)
> > cpu = of_find_node_by_name(NULL, "cpu");
> > if (!of_property_read_u32(cpu, "clock-frequency", &freq))
> > preset_lpj = freq / CONFIG_HZ / 2;
> > +
> > + for (setup = model_setup_table; setup->name; setup++) {
> > + if (strcmp(setup->name, sh_mv.mv_name) == 0) {
> > + setup->fn();
> > + break;
> > + }
> > + }
> > }
> >
> > static int sh_of_irq_demux(int irq)
> > --
>
> I think all of this code should be in appropriate driver files, not
> of-generic.c. Much of it looks like it should be pm (power management)
> drivers for which I'd assume there's an existing framework. I'm not
> sure about the DRAM control. For the LED I think there's an LED GPIO
> framework already too that would be appropriate and that probably
> only needs appropriate nodes in the DT, not even any code.
>
> Rich
OK.
I'll separate code.
--
Yoshinori Sato
<ys...@users.sourceforge.jp>
