This patch adds a binding that describes the Rockchip PCIe controller found on Rockchip SoCs PCIe interface.
Signed-off-by: Shawn Lin <shawn....@rock-chips.com> Acked-by: Rob Herring <r...@kernel.org> Reviewed-by: Brian Norris <briannor...@chromium.org> --- Changes in v9: None Changes in v8: - add Brian's review-tag Changes in v7: - move optional properties ahead of interrupt subnode - use 0-base index for INTx Changes in v6: - add ack tag from Rob Changes in v5: - fix wrong example reported by Marc - add seperate section to describe the interrupt controller child node Changes in v4: - fix example of adding intermediate interrupt controller for pcie legacy interrrupt Changes in v3: - fix example dts code suggested by Rob and Marc - remove driver's behaviour of regulator Changes in v2: - fix lots clk/reset stuff suggested by Heiko - remove msi-parent and add msi-map suggested by Marc - drop phy related stuff - some others minor fixes .../devicetree/bindings/pci/rockchip-pcie.txt | 106 +++++++++++++++++++++ 1 file changed, 106 insertions(+) create mode 100644 Documentation/devicetree/bindings/pci/rockchip-pcie.txt diff --git a/Documentation/devicetree/bindings/pci/rockchip-pcie.txt b/Documentation/devicetree/bindings/pci/rockchip-pcie.txt new file mode 100644 index 0000000..3f74c87 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/rockchip-pcie.txt @@ -0,0 +1,106 @@ +* Rockchip AXI PCIe Root Port Bridge DT description + +Required properties: +- #address-cells: Address representation for root ports, set to <3> +- #size-cells: Size representation for root ports, set to <2> +- #interrupt-cells: specifies the number of cells needed to encode an + interrupt source. The value must be 1. +- compatible: Should contain "rockchip,rk3399-pcie" +- reg: Two register ranges as listed in the reg-names property +- reg-names: Must include the following names + - "axi-base" + - "apb-base" +- clocks: Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. +- clock-names: Must include the following entries: + - "aclk" + - "aclk-perf" + - "hclk" + - "pm" +- msi-map: Maps a Requester ID to an MSI controller and associated. + See ./pci-msi.txt +- phys: From PHY bindings: Phandle for the Generic PHY for PCIe. +- phy-names: MUST be "pcie-phy". +- interrupts: Three interrupt entries must be specified. +- interrupt-names: Must include the following names + - "sys" + - "legacy" + - "client" +- resets: Must contain five entries for each entry in reset-names. + See ../reset/reset.txt for details. +- reset-names: Must include the following names + - "core" + - "mgmt" + - "mgmt-sticky" + - "pipe" +- pinctrl-names : The pin control state names +- pinctrl-0: The "default" pinctrl state +- #interrupt-cells: specifies the number of cells needed to encode an + interrupt source. The value must be 1. +- interrupt-map-mask and interrupt-map: standard PCI properties + +Optional Property: +- ep-gpios: contain the entry for pre-reset gpio +- num-lanes: number of lanes to use +- vpcie3v3-supply: The phandle to the 3.3v regulator to use for pcie. +- vpcie1v8-supply: The phandle to the 1.8v regulator to use for pcie. +- vpcie0v9-supply: The phandle to the 0.9v regulator to use for pcie. + +*Interrupt controller child node* +The core controller provides a single interrupt for legacy INTx. The pcie node +should contain an interrupt controller node as a target for the PCI +'interrupt-map' property. This node represents the domain at which the four +INTx interrupts are decoded and routed. + + +Required properties for Interrupt controller child node: +- interrupt-controller: identifies the node as an interrupt controller +- #address-cells: specifies the number of cells needed to encode an + address. The value must be 0. +- #interrupt-cells: specifies the number of cells needed to encode an + interrupt source. The value must be 1. + +Example: + +pcie0: pcie@f8000000 { + compatible = "rockchip,rk3399-pcie"; + #address-cells = <3>; + #size-cells = <2>; + clocks = <&cru ACLK_PCIE>, <&cru ACLK_PERF_PCIE>, + <&cru PCLK_PCIE>, <&cru SCLK_PCIE_PM>; + clock-names = "aclk", "aclk-perf", + "hclk", "pm"; + bus-range = <0x0 0x1>; + interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH 0>, + <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH 0>, + <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH 0>; + interrupt-names = "sys", "legacy", "client"; + assigned-clocks = <&cru SCLK_PCIEPHY_REF>; + assigned-clock-parents = <&cru SCLK_PCIEPHY_REF100M>; + assigned-clock-rates = <100000000>; + ep-gpios = <&gpio3 13 GPIO_ACTIVE_HIGH>; + ranges = <0x83000000 0x0 0xfa000000 0x0 0xfa000000 0x0 0x600000 + 0x81000000 0x0 0xfa600000 0x0 0xfa600000 0x0 0x100000>; + num-lanes = <4>; + msi-map = <0x0 &its 0x0 0x1000>; + reg = <0x0 0xf8000000 0x0 0x2000000>, <0x0 0xfd000000 0x0 0x1000000>; + reg-names = "axi-base", "apb-base"; + resets = <&cru SRST_PCIE_CORE>, <&cru SRST_PCIE_MGMT>, + <&cru SRST_PCIE_MGMT_STICKY>, <&cru SRST_PCIE_PIPE>; + reset-names = "core", "mgmt", "mgmt-sticky", "pipe"; + phys = <&pcie_phy>; + phy-names = "pcie-phy"; + pinctrl-names = "default"; + pinctrl-0 = <&pcie_clkreq>; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 7>; + interrupt-map = <0 0 0 1 &pcie0_intc 0>, + <0 0 0 2 &pcie0_intc 1>, + <0 0 0 3 &pcie0_intc 2>, + <0 0 0 4 &pcie0_intc 3>; + pcie0_intc: interrupt-controller { + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <1>; + }; +}; -- 2.3.7