tty_port_close handles much of the common parts of tty close. Convert
uart_close to use it and move the serial_core specific parts into
tty_port.shutdown function. This will be needed to use tty_port functions
directly from in kernel clients.
This change causes ops->stop_rx() to be called after uart_wait_until_sent()
is called which I think should be fine. Otherwise, the sequence of the
close should be the same.
Cc: Alan Cox <a...@linux.intel.com>
Cc: Peter Hurley <pe...@hurleysoftware.com>
Signed-off-by: Rob Herring <r...@kernel.org>
---
drivers/tty/serial/serial_core.c | 56 ++++++++++++++--------------------------
1 file changed, 19 insertions(+), 37 deletions(-)
diff --git a/drivers/tty/serial/serial_core.c b/drivers/tty/serial/serial_core.c
index 0468725..e183d2e 100644
--- a/drivers/tty/serial/serial_core.c
+++ b/drivers/tty/serial/serial_core.c
@@ -1461,7 +1461,6 @@ static void uart_close(struct tty_struct *tty, struct
file *filp)
{
struct uart_state *state = tty->driver_data;
struct tty_port *port;
- struct uart_port *uport;
if (!state) {
struct uart_driver *drv = tty->driver->driver_state;
@@ -1477,56 +1476,36 @@ static void uart_close(struct tty_struct *tty, struct
file *filp)
port = &state->port;
pr_debug("uart_close(%d) called\n", tty->index);
- if (tty_port_close_start(port, tty, filp) == 0)
- return;
+ tty_port_close(tty->port, tty, filp);
+}
- mutex_lock(&port->mutex);
- uport = uart_port_check(state);
+static void uart_tty_port_shutdown(struct tty_port *port)
+{
+ struct uart_state *state = container_of(port, struct uart_state, port);
+ struct uart_port *uport = uart_port_check(state);
+ spin_lock_irq(&uport->lock);
/*
* At this point, we stop accepting input. To do this, we
* disable the receive line status interrupts.
*/
- if (tty_port_initialized(port) &&
- !WARN(!uport, "detached port still initialized!\n")) {
- spin_lock_irq(&uport->lock);
- uport->ops->stop_rx(uport);
- spin_unlock_irq(&uport->lock);
- /*
- * Before we drop DTR, make sure the UART transmitter
- * has completely drained; this is especially
- * important if there is a transmit FIFO!
- */
- uart_wait_until_sent(tty, uport->timeout);
- }
+ WARN(!uport, "detached port still initialized!\n");
- uart_shutdown(tty, state);
- tty_port_tty_set(port, NULL);
+ uport->ops->stop_rx(uport);
- spin_lock_irq(&port->lock);
+ spin_unlock_irq(&uport->lock);
- if (port->blocked_open) {
- spin_unlock_irq(&port->lock);
- if (port->close_delay)
-
msleep_interruptible(jiffies_to_msecs(port->close_delay));
- spin_lock_irq(&port->lock);
- } else if (uport && !uart_console(uport)) {
- spin_unlock_irq(&port->lock);
- uart_change_pm(state, UART_PM_STATE_OFF);
- spin_lock_irq(&port->lock);
- }
- spin_unlock_irq(&port->lock);
- tty_port_set_active(port, 0);
+ uart_port_shutdown(port);
/*
- * Wake up anyone trying to open this port.
+ * It's possible for shutdown to be called after suspend if we get
+ * a DCD drop (hangup) at just the right time. Clear suspended bit so
+ * we don't try to resume a port that has been shutdown.
*/
- wake_up_interruptible(&port->open_wait);
+ tty_port_set_suspended(port, 0);
- mutex_unlock(&port->mutex);
+ uart_change_pm(state, UART_PM_STATE_OFF);
- tty_ldisc_flush(tty);
- tty->closing = 0;
}
static void uart_wait_until_sent(struct tty_struct *tty, int timeout)
@@ -2446,6 +2425,7 @@ static const struct tty_port_operations uart_port_ops = {
.carrier_raised = uart_carrier_raised,
.dtr_rts = uart_dtr_rts,
.activate = uart_port_activate,
+ .shutdown = uart_tty_port_shutdown,
};
/**
@@ -2762,6 +2742,8 @@ int uart_add_one_port(struct uart_driver *drv, struct
uart_port *uport)
uport->cons = drv->cons;
uport->minor = drv->tty_driver->minor_start + uport->line;
+ port->console = uart_console(uport);
+
/*
* If this port is a console, then the spinlock is already
* initialised.
--
2.9.3
