4.4-stable review patch. If anyone has any objections, please let me know.
------------------ [ Upstream commit 08c991297582114a6e1220f913eec91789c4eac6 ] The i210 has two EEPROM access registers that are located in non-standard offsets: EEARBC and EEMNGCTL. EEARBC was fixed previously and EEMNGCTL should also be corrected. Reported-by: Roman Hodek <[email protected]> Signed-off-by: Todd Fujinaka <[email protected]> Tested-by: Aaron Brown <[email protected]> Signed-off-by: Jeff Kirsher <[email protected]> Signed-off-by: Sasha Levin <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]> --- drivers/net/ethernet/intel/igb/e1000_82575.c | 1 + drivers/net/ethernet/intel/igb/e1000_i210.c | 27 +++++++++++++++++++++++++++ drivers/net/ethernet/intel/igb/e1000_i210.h | 1 + drivers/net/ethernet/intel/igb/e1000_regs.h | 1 + 4 files changed, 30 insertions(+) --- a/drivers/net/ethernet/intel/igb/e1000_82575.c +++ b/drivers/net/ethernet/intel/igb/e1000_82575.c @@ -294,6 +294,7 @@ static s32 igb_init_phy_params_82575(str case I210_I_PHY_ID: phy->type = e1000_phy_i210; phy->ops.check_polarity = igb_check_polarity_m88; + phy->ops.get_cfg_done = igb_get_cfg_done_i210; phy->ops.get_phy_info = igb_get_phy_info_m88; phy->ops.get_cable_length = igb_get_cable_length_m88_gen2; phy->ops.set_d0_lplu_state = igb_set_d0_lplu_state_82580; --- a/drivers/net/ethernet/intel/igb/e1000_i210.c +++ b/drivers/net/ethernet/intel/igb/e1000_i210.c @@ -900,3 +900,30 @@ s32 igb_pll_workaround_i210(struct e1000 wr32(E1000_MDICNFG, mdicnfg); return ret_val; } + +/** + * igb_get_cfg_done_i210 - Read config done bit + * @hw: pointer to the HW structure + * + * Read the management control register for the config done bit for + * completion status. NOTE: silicon which is EEPROM-less will fail trying + * to read the config done bit, so an error is *ONLY* logged and returns + * 0. If we were to return with error, EEPROM-less silicon + * would not be able to be reset or change link. + **/ +s32 igb_get_cfg_done_i210(struct e1000_hw *hw) +{ + s32 timeout = PHY_CFG_TIMEOUT; + u32 mask = E1000_NVM_CFG_DONE_PORT_0; + + while (timeout) { + if (rd32(E1000_EEMNGCTL_I210) & mask) + break; + usleep_range(1000, 2000); + timeout--; + } + if (!timeout) + hw_dbg("MNG configuration cycle has not completed.\n"); + + return 0; +} --- a/drivers/net/ethernet/intel/igb/e1000_i210.h +++ b/drivers/net/ethernet/intel/igb/e1000_i210.h @@ -34,6 +34,7 @@ s32 igb_write_xmdio_reg(struct e1000_hw s32 igb_init_nvm_params_i210(struct e1000_hw *hw); bool igb_get_flash_presence_i210(struct e1000_hw *hw); s32 igb_pll_workaround_i210(struct e1000_hw *hw); +s32 igb_get_cfg_done_i210(struct e1000_hw *hw); #define E1000_STM_OPCODE 0xDB00 #define E1000_EEPROM_FLASH_SIZE_WORD 0x11 --- a/drivers/net/ethernet/intel/igb/e1000_regs.h +++ b/drivers/net/ethernet/intel/igb/e1000_regs.h @@ -66,6 +66,7 @@ #define E1000_PBA 0x01000 /* Packet Buffer Allocation - RW */ #define E1000_PBS 0x01008 /* Packet Buffer Size */ #define E1000_EEMNGCTL 0x01010 /* MNG EEprom Control */ +#define E1000_EEMNGCTL_I210 0x12030 /* MNG EEprom Control */ #define E1000_EEARBC_I210 0x12024 /* EEPROM Auto Read Bus Control */ #define E1000_EEWR 0x0102C /* EEPROM Write Register - RW */ #define E1000_I2CCMD 0x01028 /* SFPI2C Command Register - RW */
