On Mon, 31 Oct 2016, Steve Twiss wrote:
> From: Steve Twiss <stwiss.opensou...@diasemi.com>
>
> MFD support for DA9061 is provided as part of the DA9062 device driver.
>
> The registers header file adds two new chip variant IDs defined in DA9061
> and DA9062 hardware. The core header file adds new software enumerations
> for listing the valid DA9061 IRQs and a da9062_compatible_types enumeration
> for distinguishing between DA9061/62 devices in software.
>
> The core source code adds a new .compatible of_device_id entry. This is
> extended from DA9062 to support both "dlg,da9061" and "dlg,da9062". The
> .data entry now holds a reference to the enumerated device type.
>
> A new regmap_irq_chip model is added for DA9061 and this supports the new
> list of regmap_irq entries. A new mfd_cell da9061_devs[] array lists the
> new sub system components for DA9061. Support is added for a new DA9061
> regmap_config which lists the correct readable, writable and volatile
> ranges for this chip.
>
> The probe function uses the device tree compatible string to switch on the
> da9062_compatible_types and configure the correct mfd cells, irq chip and
> regmap config.
>
> Kconfig is updated to reflect support for DA9061 and DA9062 PMICs.
>
> Signed-off-by: Steve Twiss <stwiss.opensou...@diasemi.com>
>
> ---
> This patch applies against linux-next and v4.8
>
> v2 -> v3
> - NO CODE CHANGE
> - Patch renamed from [PATCH V2 05/10] to [PATCH V3 5/9]
>
> v1 -> v2
> - Patch renamed from [PATCH V1 01/10] to [PATCH V2 05/10] -- these
> changes were made to fix checkpatch warnings caused by the patch
> set dependency order
> - Fixed typo in the commit message "readble" to "readable"
> - Removed the explicit cross-check to decide if there is a conflict
> between the device tree compatible string and the hardware definition.
> This patch assumes the device tree is correctly written and therefore
> removes the need for a hardware/DT sanity check.
> - Removed extra semicolon in drivers/mfd/da9062-core.c:877
> - Re-write compatible entries into numerical order
>
> Lee,
>
> This patch adds support for the DA9061 PMIC. This is done as part of the
> existing DA9062 device driver by extending the of_device_id match table.
> This in turn allows new MFD cells, irq chip and regmap definitions to
> support DA9061.
>
> Regards,
> Steve Twiss, Dialog Semiconductor Ltd.
>
>
> drivers/mfd/Kconfig | 5 +-
> drivers/mfd/da9062-core.c | 427
> +++++++++++++++++++++++++++++++++--
> include/linux/mfd/da9062/core.h | 27 ++-
> include/linux/mfd/da9062/registers.h | 2 +
> 4 files changed, 441 insertions(+), 20 deletions(-)
[...]
> @@ -475,7 +855,25 @@ static int da9062_i2c_probe(struct i2c_client *i2c,
> return -EINVAL;
> }
>
> - chip->regmap = devm_regmap_init_i2c(i2c, &da9062_regmap_config);
> + switch (chip->chip_type) {
> + case(COMPAT_TYPE_DA9061):
> + cell = da9061_devs;
> + cell_num = ARRAY_SIZE(da9061_devs);
> + irq_chip = &da9061_irq_chip;
> + config = &da9061_regmap_config;
> + break;
> + case(COMPAT_TYPE_DA9062):
> + cell = da9062_devs;
> + cell_num = ARRAY_SIZE(da9062_devs);
> + irq_chip = &da9062_irq_chip;
> + config = &da9062_regmap_config;
> + break;
> + default:
> + dev_err(chip->dev, "Unrecognised chip type\n");
> + return -ENODEV;
> + }
I very much dislike when MFD and OF functionality is mixed.
In your case you can use da9062_get_device_type() to dynamically
interrogate the device and register using the correct MFD cells that
way.
> + chip->regmap = devm_regmap_init_i2c(i2c, config);
> if (IS_ERR(chip->regmap)) {
> ret = PTR_ERR(chip->regmap);
> dev_err(chip->dev, "Failed to allocate register map: %d\n",
> @@ -493,7 +891,7 @@ static int da9062_i2c_probe(struct i2c_client *i2c,
>
> ret = regmap_add_irq_chip(chip->regmap, i2c->irq,
> IRQF_TRIGGER_LOW | IRQF_ONESHOT | IRQF_SHARED,
> - -1, &da9062_irq_chip,
> + -1, irq_chip,
What is -1?
> &chip->regmap_irq);
> if (ret) {
> dev_err(chip->dev, "Failed to request IRQ %d: %d\n",
> @@ -503,8 +901,8 @@ static int da9062_i2c_probe(struct i2c_client *i2c,
>
> irq_base = regmap_irq_chip_get_base(chip->regmap_irq);
>
> - ret = mfd_add_devices(chip->dev, PLATFORM_DEVID_NONE, da9062_devs,
> - ARRAY_SIZE(da9062_devs), NULL, irq_base,
> + ret = mfd_add_devices(chip->dev, PLATFORM_DEVID_NONE, cell,
> + cell_num, NULL, irq_base,
[...]
--
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
