On 09/29, Rajendra Nayak wrote:
> Alpha PLLs which do not support dynamic update feature
> need to be explicitly disabled before a rate change.
> The ones which do support dynamic update do so within a
> single vco range, so add a min/max freq check for such
> PLLs so they fall in the vco range.
> 
> Signed-off-by: Taniya Das <t...@codeaurora.org>

Is Taniya the author?

> Signed-off-by: Rajendra Nayak <rna...@codeaurora.org>
> ---
>  drivers/clk/qcom/clk-alpha-pll.c | 49 
> +++++++++++++++++++++++++++++++++-------
>  drivers/clk/qcom/clk-alpha-pll.h |  3 +++
>  2 files changed, 44 insertions(+), 8 deletions(-)
> 
> diff --git a/drivers/clk/qcom/clk-alpha-pll.c 
> b/drivers/clk/qcom/clk-alpha-pll.c
> index 89c7fdb..6f90a86 100644
> --- a/drivers/clk/qcom/clk-alpha-pll.c
> +++ b/drivers/clk/qcom/clk-alpha-pll.c
> @@ -382,16 +382,41 @@ clk_alpha_pll_recalc_rate(struct clk_hw *hw, unsigned 
> long parent_rate)
>  static int clk_alpha_pll_set_rate(struct clk_hw *hw, unsigned long rate,
>                                 unsigned long prate)
>  {
> +     bool enabled;
>       struct clk_alpha_pll *pll = to_clk_alpha_pll(hw);
>       const struct pll_vco *vco;
>       u32 l, off = pll->offset;
>       u64 a;
>  
>       rate = alpha_pll_round_rate(rate, prate, &l, &a);
> -     vco = alpha_pll_find_vco(pll, rate);
> -     if (!vco) {
> -             pr_err("alpha pll not in a valid vco range\n");
> -             return -EINVAL;
> +     enabled = clk_hw_is_enabled(hw);
> +
> +     if (pll->flags & SUPPORTS_DYNAMIC_UPDATE) {
> +             /*
> +              * PLLs which support dynamic updates support one single
> +              * vco range, between min_rate and max_rate supported
> +              */
> +             if (rate < pll->min_rate || rate > pll->max_rate) {
> +                     pr_err("alpha pll rate outside supported min/max 
> range\n");
> +                     return -EINVAL;
> +             }
> +     } else {
> +             /*
> +              * All alpha PLLs which do not support dynamic update,
> +              * should be disabled before a vco update.
> +              */
> +             if (enabled)
> +                     hw->init->ops->disable(hw);

Please just call the function directly instead of going through
the init structure.

> +
> +             vco = alpha_pll_find_vco(pll, rate);
> +             if (!vco) {
> +                     pr_err("alpha pll not in a valid vco range\n");
> +                     return -EINVAL;
> +             }
> +
> +             regmap_update_bits(pll->clkr.regmap, off + PLL_USER_CTL,
> +                                PLL_VCO_MASK << PLL_VCO_SHIFT,
> +                                vco->val << PLL_VCO_SHIFT);
>       }
>  
>       regmap_write(pll->clkr.regmap, off + PLL_L_VAL, l);
> diff --git a/drivers/clk/qcom/clk-alpha-pll.h 
> b/drivers/clk/qcom/clk-alpha-pll.h
> index d6e1ee2..e43a9c0 100644
> --- a/drivers/clk/qcom/clk-alpha-pll.h
> +++ b/drivers/clk/qcom/clk-alpha-pll.h
> @@ -37,8 +37,11 @@ struct clk_alpha_pll {
>  #define SUPPORTS_OFFLINE_REQ BIT(0)
>  #define SUPPORTS_16BIT_ALPHA BIT(1)
>  #define SUPPORTS_FSM_MODE    BIT(2)
> +#define SUPPORTS_DYNAMIC_UPDATE      BIT(3)
>       u8 flags;
>  
> +     unsigned long min_rate;
> +     unsigned long max_rate;

Document these?

>       struct clk_regmap clkr;
>  };
>  

-- 
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project

Reply via email to