Vincent Guittot <vincent.guit...@linaro.org> writes: > On 22 November 2016 at 19:12, Kevin Hilman <khil...@baylibre.com> wrote: >> Viresh Kumar <viresh.ku...@linaro.org> writes: >> >>> On 21-11-16, 09:07, Rob Herring wrote: >>>> On Fri, Nov 18, 2016 at 02:53:12PM +0530, Viresh Kumar wrote: >>>> > Some platforms have the capability to configure the performance state of >>>> > their Power Domains. The performance levels are represented by positive >>>> > integer values, a lower value represents lower performance state. >>>> > >>>> > The power-domains until now were only concentrating on the idle state >>>> > management of the device and this needs to change in order to reuse the >>>> > infrastructure of power domains for active state management. >>>> > >>>> > This patch introduces a new optional property for the consumers of the >>>> > power-domains: domain-performance-state. >>>> > >>>> > If the consumers don't need the capability of switching to different >>>> > domain performance states at runtime, then they can simply define their >>>> > required domain performance state in their node directly. Otherwise the >>>> > consumers can define their requirements with help of other >>>> > infrastructure, for example the OPP table. >>>> > >>>> > Signed-off-by: Viresh Kumar <viresh.ku...@linaro.org> >>>> > --- >>>> > Documentation/devicetree/bindings/power/power_domain.txt | 6 ++++++ >>>> > 1 file changed, 6 insertions(+) >>>> > >>>> > diff --git a/Documentation/devicetree/bindings/power/power_domain.txt >>>> > b/Documentation/devicetree/bindings/power/power_domain.txt >>>> > index e1650364b296..db42eacf8b5c 100644 >>>> > --- a/Documentation/devicetree/bindings/power/power_domain.txt >>>> > +++ b/Documentation/devicetree/bindings/power/power_domain.txt >>>> > @@ -106,6 +106,12 @@ domain provided by the 'parent' power controller. >>>> > - power-domains : A phandle and PM domain specifier as defined by >>>> > bindings of >>>> > the power controller specified by phandle. >>>> > >>>> > +Optional properties: >>>> > +- domain-performance-state: A positive integer value representing the >>>> > minimum >>>> > + performance level (of the parent domain) required by the consumer for >>>> > its >>>> > + working. The integer value '1' represents the lowest performance >>>> > level and the >>>> > + highest value represents the highest performance level. >>>> >>>> How does one come up with the range of values? >>> >>> Why would we need a range here? The value here represents the minimum >>> 'state' >>> and the assumption is that everything above that level would be fine. So the >>> range is automatically: domain-performance-state -> MAX. >>> >>>> It seems like you are >>>> just making up numbers. Couldn't the domain performance level be an OPP >>>> in the sense that it is a collection of clock frequencies and voltage >>>> settings? >>> >>> The clock is going to be handled by the device itself (at least for the >>> case we >>> have today) and the performance-state lies with the power-domain which is >>> configured separately. If the performance level includes both clk and >>> voltage, >>> then why would we need to show the clock rates in the DT ? Wouldn't a >>> performance level be enough in such cases? >> >> I think the question is: what does the performance-level of a domain >> actually mean? Or, what are the units? >> >> Depending on the SoC, there's probably a few things this could mean. It >> might mean is that an underlying bus/interconnect can be configured to >> guarantee a specific bandwidth or throughput. That in turn might mean >> that that bus/interconnect might have to be set at a specific >> frequency/voltage. >> >> In your case, IIUC, you're just passing some magic value to some >> firmware running on a micro-controller, but under the hood that uC is >> probably configuring a frequency/voltage someplace. > > In the case described by Viresh, it's only about setting the voltage > of a power domain that is shared between different devices. these > devices wants to run at different frequency (set by the devices) but > we have to select a Volateg value that will match with the constraint > of all devices (in this case the highest voltage)
Then, at least for this use case, we're talking about voltage, not some unspecified units. But that makes me wonder, this performance state sounds like something that is changing dynamically at runtime, so why do you want to describe this statically in DT? This sounds to me like the job of the genpd. When any device in the domain does its pm_runtime_get(), the domain could check the device frequency and see if it needs to change the domain voltage in order for that device to operate at that frequency. When the device goes away (using pm_runtime_put()) the domain can check again if it could lower the voltage and still meet the requirements of the remaining devices. Kevin
