On Wed, 30 Nov 2016 20:14:11 +0100 Jernej Škrabec <jernej.skra...@gmail.com> wrote:
> Dne četrtek, 01. december 2016 ob 03:03:14 CET je Icenowy Zheng napisal(a): > > 2016年12月1日 02:49于 Jernej Skrabec <jernej.skra...@gmail.com>写道： > > > > > Hi Jean-François, > > > > > > Dne sreda, 30. november 2016 10.35.08 UTC+1 je oseba Jean-François Moine > napisala: > > >> On Tue, 29 Nov 2016 22:59:32 +0100 > > >> > > >> Maxime Ripard <maxime...@free-electrons.com> wrote: > > >> > > > I'm still not sure which pipeline should I use. > > >> > > > > > >> > > > And, it seems that HDMI Slow Clock is not needed? > > >> > > > > > >> > > > (seems that it's only for EDID, but simplefb won't use EDID) > > >> > > > > >> > > So, I don't see how this may work. > > >> > > How can the u-boot know the resolutions of the HDMI display device? > > >> > > > > >> > > In other words: I have a new H3 board with the last u-boot and > > >> > > kernel. > > >> > > I plug my (rather old or brand new) HDMI display device. > > >> > > After powering on the system, I hope to get something on the screen. > > >> > > How? > > >> > > > >> > If it works like the driver for the first display engine in U-Boot, it > > >> > will use the preferred mode reported by the EDID, and will fallback to > > >> > 1024x768 if it cannot access it. > > >> > > >> Icenowy wrote: "simplefb won't use EDID" > > >> > > >> Then, if it is like in the kernel, the 1024x768 mode is VGA. It does > > >> not work with HDMI (different timings). > > > > > > U-Boot driver now accept any timings recommended by EDID. So far it > > > was tested with at least following resolutions: > > > - 1920x1080 @ 60 Hz > > > - 1280x1024 @ 60 Hz > > > - 1280x800 @ 60 Hz (slight clock difference) > > > - 800x480 (not sure about frame rate) > > > - 3840x2160 @ 30 Hz (4K) > > > > I tested on 1024x600 (If my memory is right, it's @ 60Hz) > > > > > and nobody complained so far. I'm pretty sure 1024x768 would work. Check the timings offered by the DRM core. > > > > > >> > Maybe it would be worth exchanging on the EDID code that has been done > > >> > for the u-boot driver too, so that it can be fixed in your driver. > > >> > > >> The u-boot got my code, and, up to now, I could not fix the random or > > >> permanent failures of EDID reading in some boards. > > > > > > I only have one OPi2, but as I said, EDID always worked for me. Happy guy! > > > The only > > > code left from you is for DE2. HDMI stuff is basically copied from Rockhip > > > driver (including EDID reading), TCON code is now reverted to the same as > > > it is in sunxi_display.c. I think it is worth to take a look at EDID code > > > and compare it. > > > > So is the TCON of DE 2.0 identical to the original TCON? > > > > If so, we should reuse sun4i-tcon ... > > Well, TCON is splitted in two parts (two base addresses), one for HDMI and > one > for TV. However, register offsets are same as before, so I guess driver > reusage make sense. I think that there are few additional registers, but they > can be ignored for simplefb. The TCON1 of the H3 is not usable (no ckock). Analog TV has its own clock and I/O area. -- Ken ar c'hentañ | ** Breizh ha Linux atav! ** Jef | http://moinejf.free.fr/
