On Fri, Dec 09, 2016 at 03:18:28PM -0600, Rob Herring wrote:
> On Fri, Dec 02, 2016 at 09:42:09AM -0600, Nathan Sullivan wrote:
> > Support the National Instruments 169445 board.
> >
> > Signed-off-by: Nathan Sullivan <nathan.sulli...@ni.com>
> > ---
> > "gpio: mmio: add support for NI 169445 NAND GPIO" and
> > "devicetree: add vendor prefix for National Instruments" are required for
> > the
> > NAND on this board to work.
>
> These should have been a series, but I already applied the first one.
>
> >
> > Documentation/devicetree/bindings/mips/ni.txt | 7 ++
> > arch/mips/Kbuild.platforms | 1 +
> > arch/mips/Kconfig | 26 ++++++
> > arch/mips/boot/dts/Makefile | 1 +
> > arch/mips/boot/dts/ni/169445.dts | 99 +++++++++++++++++++++
> > arch/mips/boot/dts/ni/Makefile | 9 ++
> > arch/mips/configs/ni169445_defconfig | 120
> > ++++++++++++++++++++++++++
> > arch/mips/ni169445/169445-console.c | 38 ++++++++
> > arch/mips/ni169445/169445-init.c | 39 +++++++++
> > arch/mips/ni169445/169445-int.c | 34 ++++++++
> > arch/mips/ni169445/169445-setup.c | 58 +++++++++++++
> > arch/mips/ni169445/169445-time.c | 35 ++++++++
> > arch/mips/ni169445/Makefile | 9 ++
> > arch/mips/ni169445/Platform | 6 ++
> > 14 files changed, 482 insertions(+)
> > create mode 100644 Documentation/devicetree/bindings/mips/ni.txt
> > create mode 100644 arch/mips/boot/dts/ni/169445.dts
> > create mode 100644 arch/mips/boot/dts/ni/Makefile
> > create mode 100644 arch/mips/configs/ni169445_defconfig
> > create mode 100644 arch/mips/ni169445/169445-console.c
> > create mode 100644 arch/mips/ni169445/169445-init.c
> > create mode 100644 arch/mips/ni169445/169445-int.c
> > create mode 100644 arch/mips/ni169445/169445-setup.c
> > create mode 100644 arch/mips/ni169445/169445-time.c
> > create mode 100644 arch/mips/ni169445/Makefile
> > create mode 100644 arch/mips/ni169445/Platform
> >
> > diff --git a/Documentation/devicetree/bindings/mips/ni.txt
> > b/Documentation/devicetree/bindings/mips/ni.txt
> > new file mode 100644
> > index 0000000..722bf2d
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/mips/ni.txt
> > @@ -0,0 +1,7 @@
> > +National Instruments MIPS platforms
> > +
> > +required root node properties:
> > + - compatible: must be "ni,169445"
> > +
> > +CPU Nodes
> > + - compatible: must be "mti,mips14KEc"
> > diff --git a/arch/mips/Kbuild.platforms b/arch/mips/Kbuild.platforms
> > index f5f1bdb..f2d7b5c 100644
> > --- a/arch/mips/Kbuild.platforms
> > +++ b/arch/mips/Kbuild.platforms
> > @@ -20,6 +20,7 @@ platforms += loongson32
> > platforms += loongson64
> > platforms += mti-malta
> > platforms += netlogic
> > +platforms += ni169445
> > platforms += paravirt
> > platforms += pic32
> > platforms += pistachio
> > diff --git a/arch/mips/Kconfig b/arch/mips/Kconfig
> > index b3c5bde..d24d11f 100644
> > --- a/arch/mips/Kconfig
> > +++ b/arch/mips/Kconfig
> > @@ -574,6 +574,32 @@ config NXP_STB225
> > help
> > Support for NXP Semiconductors STB225 Development Board.
> >
> > +config NI_169445
> > + bool "NI 169445 board"
> > + select ARCH_WANT_OPTIONAL_GPIOLIB
> > + select BOOT_ELF32
> > + select BOOT_RAW
> > + select BUILTIN_DTB
> > + select CEVT_R4K
> > + select CSRC_R4K
> > + select CPU_MIPSR2_IRQ_VI
> > + select CPU_MIPSR2_IRQ_EI
> > + select DMA_NONCOHERENT
> > + select IRQ_MIPS_CPU
> > + select LIBFDT
> > + select MIPS_MSC
> > + select SYS_HAS_CPU_MIPS32_R1
> > + select SYS_HAS_CPU_MIPS32_R2
> > + select SYS_HAS_EARLY_PRINTK
> > + select SYS_SUPPORTS_32BIT_KERNEL
> > + select SYS_SUPPORTS_LITTLE_ENDIAN
> > + select USE_OF
> > + select COMMON_CLK
> > + help
> > + This enables support for the National Instruments 169445A
> > + board.
> > +
> > +
> > config PMC_MSP
> > bool "PMC-Sierra MSP chipsets"
> > select CEVT_R4K
> > diff --git a/arch/mips/boot/dts/Makefile b/arch/mips/boot/dts/Makefile
> > index fc7a0a9..65a0ad8 100644
> > --- a/arch/mips/boot/dts/Makefile
> > +++ b/arch/mips/boot/dts/Makefile
> > @@ -3,6 +3,7 @@ dts-dirs += cavium-octeon
> > dts-dirs += ingenic
> > dts-dirs += lantiq
> > dts-dirs += mti
> > +dts-dirs += ni
> > dts-dirs += netlogic
> > dts-dirs += pic32
> > dts-dirs += qca
> > diff --git a/arch/mips/boot/dts/ni/169445.dts
> > b/arch/mips/boot/dts/ni/169445.dts
> > new file mode 100644
> > index 0000000..a2b49f9
> > --- /dev/null
> > +++ b/arch/mips/boot/dts/ni/169445.dts
> > @@ -0,0 +1,99 @@
> > +/dts-v1/;
> > +
> > +/ {
> > + #address-cells = <1>;
> > + #size-cells = <1>;
> > + compatible = "ni,169445";
> > +
> > + cpus {
> > + mips-hpt-frequency = <25000000>;
> > +
> > + cpu@0 {
> > + compatible = "mti,mips14KEc";
> > + };
> > + };
> > +
> > + memory {
>
> memory@0
>
> > + device_type = "memory";
> > + reg = <0x0 0x08000000>;
> > + };
> > +
> > + clocks {
> > + baseclk: baseclock {
> > + compatible = "fixed-clock";
> > + #clock-cells = <0>;
> > + clock-frequency = <50000000>;
> > + };
> > + };
> > +
> > + cpu_intc: cpu_intc {
> > + #address-cells = <0>;
> > + compatible = "mti,cpu-interrupt-controller";
> > + interrupt-controller;
> > + #interrupt-cells = <1>;
> > + };
> > +
> > + ahb@0 {
> > + compatible = "simple-bus";
> > + #address-cells = <1>;
> > + #size-cells = <1>;
> > + ranges;
>
> If everything is under 0x1f3xxxxx, then add in the ranges here (and the
> unit address).
>
I noticed that some systems call out their axi/ahb busses, some do not. Would
you prefer that I remove the bus entirely?
> > +
> > + gpio1: nand-gpio-out@1f300010 {
>
> As in the binding example: gpio-controller@...
>
> > + compatible = "ni,169445-nand-gpio";
> > + reg = <0x1f300010 0x4>;
> > + reg-names = "dat";
> > + gpio-controller;
> > + #gpio-cells = <2>;
> > + ngpios = <5>;
> > + };
> > +
> > + gpio2: nand-gpio-in@1f300014 {
>
> ditto
>
> > + compatible = "ni,169445-nand-gpio";
> > + reg = <0x1f300014 0x4>;
> > + reg-names = "dat";
> > + gpio-controller;
> > + #gpio-cells = <2>;
> > + ngpios = <1>;
> > + };
> > +
> > + nand@1f300000 {
> > + compatible = "gpio-control-nand";
> > + nand-on-flash-bbt;
> > + nand-ecc-mode = "soft_bch";
> > + nand-ecc-step-size = <512>;
> > + nand-ecc-strength = <4>;
> > + reg = <0x1f300000 4>;
> > + gpios = <&gpio2 0 0>, /* rdy */
> > + <&gpio1 1 0>, /* nce */
> > + <&gpio1 2 0>, /* ale */
> > + <&gpio1 3 0>, /* cle */
> > + <&gpio1 4 0>; /* nwp */
> > + };
> > +
> > + serial@1f380000 {
> > + compatible = "ns16550a";
> > + reg = <0x1f380000 0x1000>;
> > + interrupt-parent = <&cpu_intc>;
> > + interrupts = <6>;
> > + clocks = <&baseclk>;
> > + reg-shift = <0>;
> > + };
> > +
> > + ethernet@1f340000 {
> > + compatible = "snps,dwc-qos-ethernet-4.10";
> > + interrupt-parent = <&cpu_intc>;
> > + interrupts = <5>;
> > + reg = <0x1f340000 0x2000>;
> > + clock-names = "apb_pclk", "phy_ref_clk";
> > + clocks = <&baseclk>, <&baseclk>;
> > +
> > + phy-mode = "rgmii";
> > +
> > + fixed-link {
> > + speed = <1000>;
> > + full-duplex;
> > + };
> > + };
> > + };
> > +};
>
> [...]
>
> > diff --git a/arch/mips/ni169445/169445-setup.c
> > b/arch/mips/ni169445/169445-setup.c
> > new file mode 100644
> > index 0000000..80a5c91
> > --- /dev/null
> > +++ b/arch/mips/ni169445/169445-setup.c
> > @@ -0,0 +1,58 @@
> > +/* Copyright 2016 National Instruments Corporation
> > + *
> > + * This program is free software; you can redistribute it and/or modify it
> > + * under the terms of the GNU General Public License as published by the
> > Free
> > + * Software Foundation; either version 2 of the License, or (at your
> > option)
> > + * any later version.
> > + *
> > + * This program is distributed in the hope that it will be useful, but
> > WITHOUT
> > + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
> > + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
> > for
> > + * more details.
> > + */
> > +#include <linux/init.h>
> > +#include <linux/clk-provider.h>
> > +#include <linux/libfdt.h>
> > +#include <linux/of_platform.h>
> > +#include <linux/of_fdt.h>
> > +
> > +#include <asm/prom.h>
> > +#include <asm/fw/fw.h>
> > +
> > +#include <asm/mips-boards/generic.h>
> > +
> > +const char *get_system_type(void)
> > +{
> > + return "NI 169445 FPGA";
>
> Perhaps this should come from model property. There's a patch in flight
> to add a function to get machine name.
>
> > +}
> > +
> > +void __init plat_mem_setup(void)
> > +{
> > + /*
> > + * Load the builtin devicetree. This causes the chosen node to be
> > + * parsed resulting in our memory appearing
> > + */
> > + __dt_setup_arch(__dtb_start);
> > +}
> > +
> > +void __init device_tree_init(void)
> > +{
> > + if (!initial_boot_params)
> > + return;
> > +
> > + unflatten_and_copy_device_tree();
> > +}
> > +
> > +static int __init customize_machine(void)
> > +{
> > + of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
>
> This should happen by default now.
>
> > + return 0;
> > +}
> > +arch_initcall(customize_machine);
Thank you for the feedback.
Nathan
