On 12/20/2016 03:55 AM, Rob Herring wrote:
On Wed, Dec 14, 2016 at 03:04:04PM +0900, Hoegeun Kwon wrote:
This patch add support for MIPI-DSI based S6E3HA2 AMOLED panel
driver. This panel has 1440x2560 resolution in 5.7-inch physical
panel in the TM2 device.

Signed-off-by: Donghwa Lee <dh09....@samsung.com>
Signed-off-by: Hyungwon Hwang <human.hw...@samsung.com>
Signed-off-by: Hoegeun Kwon <hoegeun.k...@samsung.com>
---
  .../bindings/display/panel/samsung,s6e3ha2.txt     |  52 ++
  drivers/gpu/drm/panel/Kconfig                      |   6 +
  drivers/gpu/drm/panel/Makefile                     |   1 +
  drivers/gpu/drm/panel/panel-samsung-s6e3ha2.c      | 756 +++++++++++++++++++++
  4 files changed, 815 insertions(+)
  create mode 100644 
Documentation/devicetree/bindings/display/panel/samsung,s6e3ha2.txt
  create mode 100644 drivers/gpu/drm/panel/panel-samsung-s6e3ha2.c

diff --git 
a/Documentation/devicetree/bindings/display/panel/samsung,s6e3ha2.txt 
b/Documentation/devicetree/bindings/display/panel/samsung,s6e3ha2.txt
new file mode 100644
index 0000000..1f41f24
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/panel/samsung,s6e3ha2.txt
@@ -0,0 +1,52 @@
+Samsung S6E3HA2 5.7" 1440x2560 AMOLED panel
+
+Required properties:
+  - compatible: "samsung,s6e3ha2"
+  - reg: the virtual channel number of a DSI peripheral
+  - vdd3-supply: core voltage supply
+  - vci-supply: voltage supply for analog circuits
+  - reset-gpios: a GPIO spec for the reset pin
+  - enable-gpios: a GPIO spec for the panel enable pin
+  - te-gpios: a GPIO spec for the tearing effect synchronization signal gpio 
pin
Need to specify the GPIOs as active high or low.

Hi Rob Herring,

Thanks for point out. I will add "(active high or low)" after the description of the GPIOs.

+
+Optional properties:
+  - display-timings: timings for the connected panel as described by [1]
+
+The device node can contain one 'port' child node with one child
+'endpoint' node, according to the bindings defined in [2]. This
+node should describe panel's video bus.
+
+[1]: Documentation/devicetree/bindings/display/panel/display-timing.txt
+[2]: Documentation/devicetree/bindings/media/video-interfaces.txt
+
+Example:
+
+       panel@0 {
+               compatible = "samsung,s6e3ha2";
+               reg = <0>;
reg doesn't really work here unless this node is a child of the DSI
controller node. But if it is a child node, then you don't need the OF
graph.

The reg value is used in virtual child panel node so I think the reg value is needed.
Please refer to the document below.
Documentation/devicetree/bindings/display/mipi-dsi-bus.txt

Best Regards,
Hoegeun Kwon

+               vdd3-supply = <&ldo27_reg>;
+               vci-supply = <&ldo28_reg>;
+               reset-gpios = <&gpg0 0 GPIO_ACTIVE_HIGH>;
+               enable-gpios = <&gpf1 5 GPIO_ACTIVE_HIGH>;
+               te-gpios = <&gpf1 3 GPIO_ACTIVE_HIGH>;
+
+               display-timings {
+                       timing-0 {
+                               clock-frequency = <0>;
+                               hactive = <1440>;
+                               vactive = <2560>;
+                               hfront-porch = <1>;
+                               hback-porch = <1>;
+                               hsync-len = <1>;
+                               vfront-porch = <1>;
+                               vback-porch = <15>;
+                               vsync-len = <1>;
+                       };
+               };
+
+               port {
+                       dsi_in: endpoint {
+                               remote-endpoint = <&dsi_out>;
+                       };
+               };
+       };
_______________________________________________
dri-devel mailing list
dri-de...@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

Reply via email to