On 12/26/2016 09:10 PM, Florian Fainelli wrote:
>
>
> On 12/27/2016 03:44 AM, Kweh, Hock Leong wrote:
>> From: "Kweh, Hock Leong" <hock.leong.k...@intel.com>
>>
>> If kernel module stmmac driver being loaded after OS booted, there is a
>> race condition between stmmac_open() and stmmac_mdio_register(), which is
>> invoked inside stmmac_dvr_probe(), and the error is showed in dmesg log as
>> PHY not found and stmmac_open() failed:
>> [ 473.919358] stmmaceth 0000:01:00.0 (unnamed net_device) (uninitialized):
>> stmmac_dvr_probe: warning: cannot get CSR clock
>> [ 473.919382] stmmaceth 0000:01:00.0: no reset control found
>> [ 473.919412] stmmac - user ID: 0x10, Synopsys ID: 0x42
>> [ 473.919429] stmmaceth 0000:01:00.0: DMA HW capability register supported
>> [ 473.919436] stmmaceth 0000:01:00.0: RX Checksum Offload Engine supported
>> [ 473.919443] stmmaceth 0000:01:00.0: TX Checksum insertion supported
>> [ 473.919451] stmmaceth 0000:01:00.0 (unnamed net_device) (uninitialized):
>> Enable RX Mitigation via HW Watchdog Timer
>> [ 473.921395] libphy: PHY stmmac-1:00 not found
>> [ 473.921417] stmmaceth 0000:01:00.0 eth0: Could not attach to PHY
>> [ 473.921427] stmmaceth 0000:01:00.0 eth0: stmmac_open: Cannot attach to
>> PHY (error: -19)
>> [ 473.959710] libphy: stmmac: probed
>> [ 473.959724] stmmaceth 0000:01:00.0 eth0: PHY ID 01410cc2 at 0 IRQ POLL
>> (stmmac-1:00) active
>> [ 473.959728] stmmaceth 0000:01:00.0 eth0: PHY ID 01410cc2 at 1 IRQ POLL
>> (stmmac-1:01)
>> [ 473.959731] stmmaceth 0000:01:00.0 eth0: PHY ID 01410cc2 at 2 IRQ POLL
>> (stmmac-1:02)
>> [ 473.959734] stmmaceth 0000:01:00.0 eth0: PHY ID 01410cc2 at 3 IRQ POLL
>> (stmmac-1:03)
>>
>> The resolution used wait_for_completion_interruptible() to synchronize
>> stmmac_open() and stmmac_dvr_probe() to prevent the race condition
>> happening.
>
> The proper fix for this would be to have register_netdev() be the last
> thing done in stmmac_drv_probe(), whereas right now, the last thing done
> is stmmac_mdio_register(), leading the window you are seeing here, where
> the network interface can be open prior to all resources being set up,
> including, but not limited to MDIO devices.
Something like the following untested patch should plug this race:
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
index bb40382e205d..5910ea51f8f6 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
@@ -3339,13 +3339,6 @@ int stmmac_dvr_probe(struct device *device,
spin_lock_init(&priv->lock);
- ret = register_netdev(ndev);
- if (ret) {
- netdev_err(priv->dev, "%s: ERROR %i registering the
device\n",
- __func__, ret);
- goto error_netdev_register;
- }
-
/* If a specific clk_csr value is passed from the platform
* this means that the CSR Clock Range selection cannot be
* changed at run-time and it is fixed. Viceversa the driver'll
try to
@@ -3372,11 +3365,14 @@ int stmmac_dvr_probe(struct device *device,
}
}
- return 0;
+ ret = register_netdev(ndev);
+ if (ret)
+ netdev_err(priv->dev, "%s: ERROR %i registering the
device\n",
+ __func__, ret);
+
+ return ret;
error_mdio_register:
- unregister_netdev(ndev);
-error_netdev_register:
netif_napi_del(&priv->napi);
error_hw_init:
clk_disable_unprepare(priv->pclk);
--
Florian
