On Wed, Jan 18, 2017 at 02:00:14PM +0800, Chunfeng Yun wrote:
> add a new compatible string for "mt2712", and a new reference clock
> for SuperSpeed analog phy;
>
> Signed-off-by: Chunfeng Yun <[email protected]>
> ---
> .../devicetree/bindings/phy/phy-mt65xx-usb.txt | 81
> +++++++++++++++++---
> 1 file changed, 70 insertions(+), 11 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt
> b/Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt
> index 33a2b1e..8f91136 100644
> --- a/Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt
> +++ b/Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt
> @@ -6,19 +6,25 @@ This binding describes a usb3.0 phy for mt65xx platforms of
> Medaitek SoC.
> Required properties (controller (parent) node):
> - compatible : should be one of
> "mediatek,mt2701-u3phy"
> + "mediatek,mt2712-u3phy"
> "mediatek,mt8173-u3phy"
> - - reg : offset and length of register for phy, exclude port's
> - register.
> - clocks : a list of phandle + clock-specifier pairs, one for each
> entry in clock-names
> - clock-names : must contain
> - "u3phya_ref": for reference clock of usb3.0 analog phy.
> + "u2ref_clk": 48M reference clock of HighSpeed analog phy.
> + "u3ref_clk": 26M reference clock of SuperSpeed analog phy,
> + sometimes is 24M, 25M or 27M, depended on platform.
_clk is redundant.
>
> Required nodes : a sub-node is required for each port the controller
> provides. Address range information including the usual
> 'reg' property is used inside these nodes to describe
> the controller's topology.
>
> +Optional properties (controller (parent) node):
> + - reg : offset and length of register shared by multiple
> ports,
> + exclude port's private register. It is needed on mt2701
> + and mt8173, but not on mt2712.
> +
> Required properties (port (child) node):
> - reg : address and length of the register set for the port.
> - #phy-cells : should be 1 (See second example)
> @@ -31,21 +37,27 @@ Example:
> u3phy: usb-phy@11290000 {
> compatible = "mediatek,mt8173-u3phy";
> reg = <0 0x11290000 0 0x800>;
> - clocks = <&apmixedsys CLK_APMIXED_REF2USB_TX>;
> - clock-names = "u3phya_ref";
> + clocks = <&apmixedsys CLK_APMIXED_REF2USB_TX>, <&clk26m>;
> + clock-names = "u2ref_clk", "u3ref_clk";
> #address-cells = <2>;
> #size-cells = <2>;
> ranges;
> status = "okay";
>
> - phy_port0: port@11290800 {
> - reg = <0 0x11290800 0 0x800>;
> + u2port0: port@11290800 {
port is for OF graph. This should be usb-phy@... instead.
> + reg = <0 0x11290800 0 0x100>;
> + #phy-cells = <1>;
> + status = "okay";
> + };
> +
> + u3port0: port@11290900 {
> + reg = <0 0x11290800 0 0x700>;
> #phy-cells = <1>;
> status = "okay";
> };
>
> - phy_port1: port@11291000 {
> - reg = <0 0x11291000 0 0x800>;
> + u2port1: port@11291000 {
> + reg = <0 0x11291000 0 0x100>;
> #phy-cells = <1>;
> status = "okay";
> };
> @@ -64,7 +76,54 @@ Example:
>
> usb30: usb@11270000 {
> ...
> - phys = <&phy_port0 PHY_TYPE_USB3>;
> - phy-names = "usb3-0";
> + phys = <&u2port0 PHY_TYPE_USB2>, <&u3port0 PHY_TYPE_USB3>;
> + phy-names = "usb2-0", "usb3-0";
> ...
> };
> +
> +
> +Layout differences of banks between mt8173/mt2701 and mt2712
> +-------------------------------------------------------------
> +mt8173 and mt2701:
> +port offset bank
> +shared 0x0000 SPLLC
> + 0x0100 FMREG
> +u2 port0 0x0800 U2PHY_COM
> +u3 port0 0x0900 U3PHYD
> + 0x0a00 U3PHYD_BANK2
> + 0x0b00 U3PHYA
> + 0x0c00 U3PHYA_DA
> +u2 port1 0x1000 U2PHY_COM
> +u3 port1 0x1100 U3PHYD
> + 0x1200 U3PHYD_BANK2
> + 0x1300 U3PHYA
> + 0x1400 U3PHYA_DA
> +u2 port2 0x1800 U2PHY_COM
> + ...
> +
> +mt2712:
> +port offset bank
> +u2 port0 0x0000 MISC
> + 0x0100 FMREG
> + 0x0300 U2PHY_COM
> +u3 port0 0x0700 SPLLC
> + 0x0800 CHIP
> + 0x0900 U3PHYD
> + 0x0a00 U3PHYD_BANK2
> + 0x0b00 U3PHYA
> + 0x0c00 U3PHYA_DA
> +u2 port1 0x1000 MISC
> + 0x1100 FMREG
> + 0x1300 U2PHY_COM
> +u3 port1 0x1700 SPLLC
> + 0x1800 CHIP
> + 0x1900 U3PHYD
> + 0x1a00 U3PHYD_BANK2
> + 0x1b00 U3PHYA
> + 0x1c00 U3PHYA_DA
> +u2 port2 0x2000 MISC
> + ...
> +
> + SPLLC shared by u3 ports and FMREG shared by u2 ports on
> +mt8173/mt2701 are put back into each port; a new bank MISC for
> +u2 ports and CHIP for u3 ports are added on mt2712.
> --
> 1.7.9.5
>
