Le 20/02/2017 à 13:28, Boris Brezillon a écrit :
> The old NAND bindings were not exactly describing the hardware topology
> and were preventing definitions of several NAND chips under the same
> NAND controller.
>
> New bindings address these limitations and should be preferred over the
> old ones for new SoCs/boards.
> Old bindings are still supported for backward compatibility but are
> marked deprecated in the doc.
>
> Signed-off-by: Boris Brezillon <boris.brezil...@free-electrons.com>
I think I already added it but here is my:
Reviewed-by: Nicolas Ferre <nicolas.fe...@microchip.com>
> ---
> .../devicetree/bindings/mtd/atmel-nand.txt | 107
> ++++++++++++++++++++-
> 1 file changed, 106 insertions(+), 1 deletion(-)
>
> diff --git a/Documentation/devicetree/bindings/mtd/atmel-nand.txt
> b/Documentation/devicetree/bindings/mtd/atmel-nand.txt
> index 3e7ee99d3949..f6bee57e453a 100644
> --- a/Documentation/devicetree/bindings/mtd/atmel-nand.txt
> +++ b/Documentation/devicetree/bindings/mtd/atmel-nand.txt
> @@ -1,4 +1,109 @@
> -Atmel NAND flash
> +Atmel NAND flash controller bindings
> +
> +The NAND flash controller node should be defined under the EBI bus (see
> +Documentation/devicetree/bindings/memory-controllers/atmel,ebi.txt).
> +One or several NAND devices can be defined under this NAND controller.
> +The NAND controller might be connected to an ECC engine.
> +
> +* NAND controller bindings:
> +
> +Required properties:
> +- compatible: should be one of the following
> + "atmel,at91rm9200-nand-controller"
> + "atmel,at91sam9260-nand-controller"
> + "atmel,at91sam9261-nand-controller"
> + "atmel,at91sam9g45-nand-controller"
> + "atmel,sama5d3-nand-controller"
> +- ranges: empty ranges property to forward EBI ranges definitions.
> +- #address-cells: should be set to 2.
> +- #size-cells: should be set to 1.
> +- atmel,nfc-io: phandle to the NFC IO block. Only required for sama5d3
> + controllers.
> +- atmel,nfc-sram: phandle to the NFC SRAM block. Only required for sama5d3
> + controllers.
> +
> +Optional properties:
> +- ecc-engine: phandle to the PMECC block. Only meaningful if the SoC embeds
> + a PMECC engine.
> +
> +* NAND device/chip bindings:
> +
> +Required properties:
> +- reg: describes the CS lines assigned to the NAND device. If the NAND device
> + exposes multiple CS lines (multi-dies chips), your reg property will
> + contain X tuples of 3 entries.
> + 1st entry: the CS line this NAND chip is connected to
> + 2nd entry: the base offset of the memory region assigned to this
> + device (always 0)
> + 3rd entry: the memory region size (always 0x800000)
> +
> +Optional properties:
> +- rb-gpios: the GPIO(s) used to check the Ready/Busy status of the NAND.
> +- cs-gpios: the GPIO(s) used to control the CS line.
> +- det-gpios: the GPIO used to detect if a Smartmedia Card is present.
> +- atmel,rb: an integer identifying the native Ready/Busy pin. Only meaningful
> + on sama5 SoCs.
> +
> +All generic properties described in
> +Documentation/devicetree/bindings/mtd/{common,nand}.txt also apply to the
> NAND
> +device node, and NAND partitions should be defined under the NAND node as
> +described in Documentation/devicetree/bindings/mtd/partition.txt.
> +
> +* ECC engine (PMECC) bindings:
> +
> +Required properties:
> +- compatible: should be one of the following
> + "atmel,at91sam9g45-pmecc"
> + "atmel,sama5d4-pmecc"
> + "atmel,sama5d2-pmecc"
> +- reg: should contain 2 register ranges. The first one is pointing to the
> PMECC
> + block, and the second one to the PMECC_ERRLOC block.
> +
> +Example:
> +
> + pmecc: ecc-engine@ffffc070 {
> + compatible = "atmel,at91sam9g45-pmecc";
> + reg = <0xffffc070 0x490>,
> + <0xffffc500 0x100>;
> + };
> +
> + ebi: ebi@10000000 {
> + compatible = "atmel,sama5d3-ebi";
> + #address-cells = <2>;
> + #size-cells = <1>;
> + atmel,smc = <&hsmc>;
> + reg = <0x10000000 0x10000000
> + 0x40000000 0x30000000>;
> + ranges = <0x0 0x0 0x10000000 0x10000000
> + 0x1 0x0 0x40000000 0x10000000
> + 0x2 0x0 0x50000000 0x10000000
> + 0x3 0x0 0x60000000 0x10000000>;
> + clocks = <&mck>;
> +
> + nand_controller: nand-controller {
> + compatible = "atmel,sama5d3-nand-controller";
> + atmel,nfc-sram = <&nfc_sram>;
> + atmel,nfc-io = <&nfc_io>;
> + ecc-engine = <&pmecc>;
> + #address-cells = <2>;
> + #size-cells = <1>;
> + ranges;
> +
> + nand@3 {
> + reg = <0x3 0x0 0x800000>;
> + atmel,rb = <0>;
> +
> + /*
> + * Put generic NAND/MTD properties and
> + * subnodes here.
> + */
> + };
> + };
> + };
> +
> +-----------------------------------------------------------------------
> +
> +Deprecated bindings (should not be used in new device trees):
>
> Required properties:
> - compatible: The possible values are:
>
--
Nicolas Ferre
