On Tue, 28 Feb 2017, Milo Kim wrote: > TI LMU (Lighting Management Unit) driver supports lighting devices below. > > LM3532, LM3631, LM3632, LM3633, LM3695 and LM3697. > > LMU devices have common features. > - I2C interface for accessing device registers > - Hardware enable pin control > - Backlight brightness control > - Notifier for hardware fault monitoring > - Regulators for LCD display bias > > It contains fault monitor, backlight, LED and regulator driver. > > LMU fault monitor > ----------------- > LM3633 and LM3697 provide hardware monitoring feature. > It enables open or short circuit detection. > After monitoring is done, each device should be re-initialized. > Notifier is used for this case. > Separate patch for 'ti-lmu-fault-monitor' will be sent later. > > Backlight > --------- > It's handled by TI LMU backlight consolidated driver and > chip dependent data. Separate patchset will be sent later. > > LED indicator > ------------- > LM3633 has 6 indicator LEDs. Programmable dimming pattern is also > supported. Separate patch for 'leds-lm3633' will be sent later. > > Regulator > --------- > LM3631 has 5 regulators for the display bias. > LM3632 supports 3 regulators. One consolidated driver enables it. > The lm363x regulator driver is already upstreamed. > > Acked-by: Lee Jones <lee.jo...@linaro.org> > Signed-off-by: Milo Kim <milo....@ti.com> > --- > drivers/mfd/Kconfig | 12 ++ > drivers/mfd/Makefile | 2 + > drivers/mfd/ti-lmu.c | 259 +++++++++++++++++++++++++++++++++ > include/linux/mfd/ti-lmu-register.h | 280 > ++++++++++++++++++++++++++++++++++++ > include/linux/mfd/ti-lmu.h | 87 +++++++++++ > 5 files changed, 640 insertions(+) > create mode 100644 drivers/mfd/ti-lmu.c > create mode 100644 include/linux/mfd/ti-lmu-register.h > create mode 100644 include/linux/mfd/ti-lmu.h
Applied, thanks. > diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig > index 55ecdfb74d31..75e749c1ff1a 100644 > --- a/drivers/mfd/Kconfig > +++ b/drivers/mfd/Kconfig > @@ -1164,6 +1164,18 @@ config MFD_LP8788 > TI LP8788 PMU supports regulators, battery charger, RTC, > ADC, backlight driver and current sinks. > > +config MFD_TI_LMU > + tristate "TI Lighting Management Unit driver" > + depends on I2C > + select MFD_CORE > + select REGMAP_I2C > + help > + Say yes here to enable support for TI LMU chips. > + > + TI LMU MFD supports LM3532, LM3631, LM3632, LM3633, LM3695 and LM3697. > + It consists of backlight, LED and regulator driver. > + It provides consistent device controls for lighting functions. > + > config MFD_OMAP_USB_HOST > bool "TI OMAP USBHS core and TLL driver" > depends on USB_EHCI_HCD_OMAP || USB_OHCI_HCD_OMAP3 > diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile > index 31ce07611a6f..dac78a0f23a7 100644 > --- a/drivers/mfd/Makefile > +++ b/drivers/mfd/Makefile > @@ -125,6 +125,8 @@ obj-$(CONFIG_MFD_AXP20X_RSB) += axp20x-rsb.o > obj-$(CONFIG_MFD_LP3943) += lp3943.o > obj-$(CONFIG_MFD_LP8788) += lp8788.o lp8788-irq.o > > +obj-$(CONFIG_MFD_TI_LMU) += ti-lmu.o > + > da9055-objs := da9055-core.o da9055-i2c.o > obj-$(CONFIG_MFD_DA9055) += da9055.o > obj-$(CONFIG_MFD_DA9062) += da9062-core.o > diff --git a/drivers/mfd/ti-lmu.c b/drivers/mfd/ti-lmu.c > new file mode 100644 > index 000000000000..cfb411cde51c > --- /dev/null > +++ b/drivers/mfd/ti-lmu.c > @@ -0,0 +1,259 @@ > +/* > + * TI LMU (Lighting Management Unit) Core Driver > + * > + * Copyright 2017 Texas Instruments > + * > + * Author: Milo Kim <milo....@ti.com> > + * > + * This program is free software; you can redistribute it and/or modify > + * it under the terms of the GNU General Public License version 2 as > + * published by the Free Software Foundation. > + */ > + > +#include <linux/delay.h> > +#include <linux/err.h> > +#include <linux/gpio.h> > +#include <linux/i2c.h> > +#include <linux/kernel.h> > +#include <linux/mfd/core.h> > +#include <linux/mfd/ti-lmu.h> > +#include <linux/mfd/ti-lmu-register.h> > +#include <linux/module.h> > +#include <linux/of.h> > +#include <linux/of_device.h> > +#include <linux/of_gpio.h> > +#include <linux/slab.h> > + > +struct ti_lmu_data { > + struct mfd_cell *cells; > + int num_cells; > + unsigned int max_register; > +}; > + > +static int ti_lmu_enable_hw(struct ti_lmu *lmu, enum ti_lmu_id id) > +{ > + int ret; > + > + if (gpio_is_valid(lmu->en_gpio)) { > + ret = devm_gpio_request_one(lmu->dev, lmu->en_gpio, > + GPIOF_OUT_INIT_HIGH, "lmu_hwen"); > + if (ret) { > + dev_err(lmu->dev, "Can not request enable GPIO: %d\n", > + ret); > + return ret; > + } > + } > + > + /* Delay about 1ms after HW enable pin control */ > + usleep_range(1000, 1500); > + > + /* LM3631 has additional power up sequence - enable LCD_EN bit. */ > + if (id == LM3631) { > + return regmap_update_bits(lmu->regmap, LM3631_REG_DEVCTRL, > + LM3631_LCD_EN_MASK, > + LM3631_LCD_EN_MASK); > + } > + > + return 0; > +} > + > +static void ti_lmu_disable_hw(struct ti_lmu *lmu) > +{ > + if (gpio_is_valid(lmu->en_gpio)) > + gpio_set_value(lmu->en_gpio, 0); > +} > + > +static struct mfd_cell lm3532_devices[] = { > + { > + .name = "ti-lmu-backlight", > + .id = LM3532, > + .of_compatible = "ti,lm3532-backlight", > + }, > +}; > + > +#define LM363X_REGULATOR(_id) \ > +{ \ > + .name = "lm363x-regulator", \ > + .id = _id, \ > + .of_compatible = "ti,lm363x-regulator", \ > +} \ > + > +static struct mfd_cell lm3631_devices[] = { > + LM363X_REGULATOR(LM3631_BOOST), > + LM363X_REGULATOR(LM3631_LDO_CONT), > + LM363X_REGULATOR(LM3631_LDO_OREF), > + LM363X_REGULATOR(LM3631_LDO_POS), > + LM363X_REGULATOR(LM3631_LDO_NEG), > + { > + .name = "ti-lmu-backlight", > + .id = LM3631, > + .of_compatible = "ti,lm3631-backlight", > + }, > +}; > + > +static struct mfd_cell lm3632_devices[] = { > + LM363X_REGULATOR(LM3632_BOOST), > + LM363X_REGULATOR(LM3632_LDO_POS), > + LM363X_REGULATOR(LM3632_LDO_NEG), > + { > + .name = "ti-lmu-backlight", > + .id = LM3632, > + .of_compatible = "ti,lm3632-backlight", > + }, > +}; > + > +static struct mfd_cell lm3633_devices[] = { > + { > + .name = "ti-lmu-backlight", > + .id = LM3633, > + .of_compatible = "ti,lm3633-backlight", > + }, > + { > + .name = "lm3633-leds", > + .of_compatible = "ti,lm3633-leds", > + }, > + /* Monitoring driver for open/short circuit detection */ > + { > + .name = "ti-lmu-fault-monitor", > + .id = LM3633, > + .of_compatible = "ti,lm3633-fault-monitor", > + }, > +}; > + > +static struct mfd_cell lm3695_devices[] = { > + { > + .name = "ti-lmu-backlight", > + .id = LM3695, > + .of_compatible = "ti,lm3695-backlight", > + }, > +}; > + > +static struct mfd_cell lm3697_devices[] = { > + { > + .name = "ti-lmu-backlight", > + .id = LM3697, > + .of_compatible = "ti,lm3697-backlight", > + }, > + /* Monitoring driver for open/short circuit detection */ > + { > + .name = "ti-lmu-fault-monitor", > + .id = LM3697, > + .of_compatible = "ti,lm3697-fault-monitor", > + }, > +}; > + > +#define TI_LMU_DATA(chip, max_reg) \ > +static const struct ti_lmu_data chip##_data = \ > +{ \ > + .cells = chip##_devices, \ > + .num_cells = ARRAY_SIZE(chip##_devices),\ > + .max_register = max_reg, \ > +} \ > + > +TI_LMU_DATA(lm3532, LM3532_MAX_REG); > +TI_LMU_DATA(lm3631, LM3631_MAX_REG); > +TI_LMU_DATA(lm3632, LM3632_MAX_REG); > +TI_LMU_DATA(lm3633, LM3633_MAX_REG); > +TI_LMU_DATA(lm3695, LM3695_MAX_REG); > +TI_LMU_DATA(lm3697, LM3697_MAX_REG); > + > +static const struct of_device_id ti_lmu_of_match[] = { > + { .compatible = "ti,lm3532", .data = &lm3532_data }, > + { .compatible = "ti,lm3631", .data = &lm3631_data }, > + { .compatible = "ti,lm3632", .data = &lm3632_data }, > + { .compatible = "ti,lm3633", .data = &lm3633_data }, > + { .compatible = "ti,lm3695", .data = &lm3695_data }, > + { .compatible = "ti,lm3697", .data = &lm3697_data }, > + { } > +}; > +MODULE_DEVICE_TABLE(of, ti_lmu_of_match); > + > +static int ti_lmu_probe(struct i2c_client *cl, const struct i2c_device_id > *id) > +{ > + struct device *dev = &cl->dev; > + const struct of_device_id *match; > + const struct ti_lmu_data *data; > + struct regmap_config regmap_cfg; > + struct ti_lmu *lmu; > + int ret; > + > + match = of_match_device(ti_lmu_of_match, dev); > + if (!match) > + return -ENODEV; > + /* > + * Get device specific data from of_match table. > + * This data is defined by using TI_LMU_DATA() macro. > + */ > + data = (struct ti_lmu_data *)match->data; > + > + lmu = devm_kzalloc(dev, sizeof(*lmu), GFP_KERNEL); > + if (!lmu) > + return -ENOMEM; > + > + lmu->dev = &cl->dev; > + > + /* Setup regmap */ > + memset(®map_cfg, 0, sizeof(struct regmap_config)); > + regmap_cfg.reg_bits = 8; > + regmap_cfg.val_bits = 8; > + regmap_cfg.name = id->name; > + regmap_cfg.max_register = data->max_register; > + > + lmu->regmap = devm_regmap_init_i2c(cl, ®map_cfg); > + if (IS_ERR(lmu->regmap)) > + return PTR_ERR(lmu->regmap); > + > + /* HW enable pin control and additional power up sequence if required */ > + lmu->en_gpio = of_get_named_gpio(dev->of_node, "enable-gpios", 0); > + ret = ti_lmu_enable_hw(lmu, id->driver_data); > + if (ret) > + return ret; > + > + /* > + * Fault circuit(open/short) can be detected by ti-lmu-fault-monitor. > + * After fault detection is done, some devices should re-initialize > + * configuration. The notifier enables such kind of handling. > + */ > + BLOCKING_INIT_NOTIFIER_HEAD(&lmu->notifier); > + > + i2c_set_clientdata(cl, lmu); > + > + return mfd_add_devices(lmu->dev, 0, data->cells, > + data->num_cells, NULL, 0, NULL); > +} > + > +static int ti_lmu_remove(struct i2c_client *cl) > +{ > + struct ti_lmu *lmu = i2c_get_clientdata(cl); > + > + ti_lmu_disable_hw(lmu); > + mfd_remove_devices(lmu->dev); > + return 0; > +} > + > +static const struct i2c_device_id ti_lmu_ids[] = { > + { "lm3532", LM3532 }, > + { "lm3631", LM3631 }, > + { "lm3632", LM3632 }, > + { "lm3633", LM3633 }, > + { "lm3695", LM3695 }, > + { "lm3697", LM3697 }, > + { } > +}; > +MODULE_DEVICE_TABLE(i2c, ti_lmu_ids); > + > +static struct i2c_driver ti_lmu_driver = { > + .probe = ti_lmu_probe, > + .remove = ti_lmu_remove, > + .driver = { > + .name = "ti-lmu", > + .of_match_table = ti_lmu_of_match, > + }, > + .id_table = ti_lmu_ids, > +}; > + > +module_i2c_driver(ti_lmu_driver); > + > +MODULE_DESCRIPTION("TI LMU MFD Core Driver"); > +MODULE_AUTHOR("Milo Kim"); > +MODULE_LICENSE("GPL v2"); > diff --git a/include/linux/mfd/ti-lmu-register.h > b/include/linux/mfd/ti-lmu-register.h > new file mode 100644 > index 000000000000..2125c7c02818 > --- /dev/null > +++ b/include/linux/mfd/ti-lmu-register.h > @@ -0,0 +1,280 @@ > +/* > + * TI LMU (Lighting Management Unit) Device Register Map > + * > + * Copyright 2017 Texas Instruments > + * > + * Author: Milo Kim <milo....@ti.com> > + * > + * This program is free software; you can redistribute it and/or modify > + * it under the terms of the GNU General Public License version 2 as > + * published by the Free Software Foundation. > + */ > + > +#ifndef __MFD_TI_LMU_REGISTER_H__ > +#define __MFD_TI_LMU_REGISTER_H__ > + > +#include <linux/bitops.h> > + > +/* LM3532 */ > +#define LM3532_REG_OUTPUT_CFG 0x10 > +#define LM3532_ILED1_CFG_MASK 0x03 > +#define LM3532_ILED2_CFG_MASK 0x0C > +#define LM3532_ILED3_CFG_MASK 0x30 > +#define LM3532_ILED1_CFG_SHIFT 0 > +#define LM3532_ILED2_CFG_SHIFT 2 > +#define LM3532_ILED3_CFG_SHIFT 4 > + > +#define LM3532_REG_RAMPUP 0x12 > +#define LM3532_REG_RAMPDN LM3532_REG_RAMPUP > +#define LM3532_RAMPUP_MASK 0x07 > +#define LM3532_RAMPUP_SHIFT 0 > +#define LM3532_RAMPDN_MASK 0x38 > +#define LM3532_RAMPDN_SHIFT 3 > + > +#define LM3532_REG_ENABLE 0x1D > + > +#define LM3532_REG_PWM_A_CFG 0x13 > +#define LM3532_PWM_A_MASK 0x05 /* zone 0 */ > +#define LM3532_PWM_ZONE_0 BIT(2) > + > +#define LM3532_REG_PWM_B_CFG 0x14 > +#define LM3532_PWM_B_MASK 0x09 /* zone 1 */ > +#define LM3532_PWM_ZONE_1 BIT(3) > + > +#define LM3532_REG_PWM_C_CFG 0x15 > +#define LM3532_PWM_C_MASK 0x11 /* zone 2 */ > +#define LM3532_PWM_ZONE_2 BIT(4) > + > +#define LM3532_REG_ZONE_CFG_A 0x16 > +#define LM3532_REG_ZONE_CFG_B 0x18 > +#define LM3532_REG_ZONE_CFG_C 0x1A > +#define LM3532_ZONE_MASK (BIT(2) | BIT(3) | BIT(4)) > +#define LM3532_ZONE_0 0 > +#define LM3532_ZONE_1 BIT(2) > +#define LM3532_ZONE_2 BIT(3) > + > +#define LM3532_REG_BRT_A 0x70 /* zone 0 */ > +#define LM3532_REG_BRT_B 0x76 /* zone 1 */ > +#define LM3532_REG_BRT_C 0x7C /* zone 2 */ > + > +#define LM3532_MAX_REG 0x7E > + > +/* LM3631 */ > +#define LM3631_REG_DEVCTRL 0x00 > +#define LM3631_LCD_EN_MASK BIT(1) > +#define LM3631_BL_EN_MASK BIT(0) > + > +#define LM3631_REG_BRT_LSB 0x01 > +#define LM3631_REG_BRT_MSB 0x02 > + > +#define LM3631_REG_BL_CFG 0x06 > +#define LM3631_BL_CHANNEL_MASK BIT(3) > +#define LM3631_BL_DUAL_CHANNEL 0 > +#define LM3631_BL_SINGLE_CHANNEL BIT(3) > +#define LM3631_MAP_MASK BIT(5) > +#define LM3631_EXPONENTIAL_MAP 0 > + > +#define LM3631_REG_BRT_MODE 0x08 > +#define LM3631_MODE_MASK (BIT(1) | BIT(2) | BIT(3)) > +#define LM3631_DEFAULT_MODE (BIT(1) | BIT(3)) > + > +#define LM3631_REG_SLOPE 0x09 > +#define LM3631_SLOPE_MASK 0xF0 > +#define LM3631_SLOPE_SHIFT 4 > + > +#define LM3631_REG_LDO_CTRL1 0x0A > +#define LM3631_EN_OREF_MASK BIT(0) > +#define LM3631_EN_VNEG_MASK BIT(1) > +#define LM3631_EN_VPOS_MASK BIT(2) > + > +#define LM3631_REG_LDO_CTRL2 0x0B > +#define LM3631_EN_CONT_MASK BIT(0) > + > +#define LM3631_REG_VOUT_CONT 0x0C > +#define LM3631_VOUT_CONT_MASK (BIT(6) | BIT(7)) > + > +#define LM3631_REG_VOUT_BOOST 0x0C > +#define LM3631_REG_VOUT_POS 0x0D > +#define LM3631_REG_VOUT_NEG 0x0E > +#define LM3631_REG_VOUT_OREF 0x0F > +#define LM3631_VOUT_MASK 0x3F > + > +#define LM3631_REG_ENTIME_VCONT 0x0B > +#define LM3631_ENTIME_CONT_MASK 0x70 > + > +#define LM3631_REG_ENTIME_VOREF 0x0F > +#define LM3631_REG_ENTIME_VPOS 0x10 > +#define LM3631_REG_ENTIME_VNEG 0x11 > +#define LM3631_ENTIME_MASK 0xF0 > +#define LM3631_ENTIME_SHIFT 4 > + > +#define LM3631_MAX_REG 0x16 > + > +/* LM3632 */ > +#define LM3632_REG_CONFIG1 0x02 > +#define LM3632_OVP_MASK (BIT(5) | BIT(6) | > BIT(7)) > +#define LM3632_OVP_25V BIT(6) > + > +#define LM3632_REG_CONFIG2 0x03 > +#define LM3632_SWFREQ_MASK BIT(7) > +#define LM3632_SWFREQ_1MHZ BIT(7) > + > +#define LM3632_REG_BRT_LSB 0x04 > +#define LM3632_REG_BRT_MSB 0x05 > + > +#define LM3632_REG_IO_CTRL 0x09 > +#define LM3632_PWM_MASK BIT(6) > +#define LM3632_I2C_MODE 0 > +#define LM3632_PWM_MODE BIT(6) > + > +#define LM3632_REG_ENABLE 0x0A > +#define LM3632_BL_EN_MASK BIT(0) > +#define LM3632_BL_CHANNEL_MASK (BIT(3) | BIT(4)) > +#define LM3632_BL_SINGLE_CHANNEL BIT(4) > +#define LM3632_BL_DUAL_CHANNEL BIT(3) > + > +#define LM3632_REG_BIAS_CONFIG 0x0C > +#define LM3632_EXT_EN_MASK BIT(0) > +#define LM3632_EN_VNEG_MASK BIT(1) > +#define LM3632_EN_VPOS_MASK BIT(2) > + > +#define LM3632_REG_VOUT_BOOST 0x0D > +#define LM3632_REG_VOUT_POS 0x0E > +#define LM3632_REG_VOUT_NEG 0x0F > +#define LM3632_VOUT_MASK 0x3F > + > +#define LM3632_MAX_REG 0x10 > + > +/* LM3633 */ > +#define LM3633_REG_HVLED_OUTPUT_CFG 0x10 > +#define LM3633_HVLED1_CFG_MASK BIT(0) > +#define LM3633_HVLED2_CFG_MASK BIT(1) > +#define LM3633_HVLED3_CFG_MASK BIT(2) > +#define LM3633_HVLED1_CFG_SHIFT 0 > +#define LM3633_HVLED2_CFG_SHIFT 1 > +#define LM3633_HVLED3_CFG_SHIFT 2 > + > +#define LM3633_REG_BANK_SEL 0x11 > + > +#define LM3633_REG_BL0_RAMP 0x12 > +#define LM3633_REG_BL1_RAMP 0x13 > +#define LM3633_BL_RAMPUP_MASK 0xF0 > +#define LM3633_BL_RAMPUP_SHIFT 4 > +#define LM3633_BL_RAMPDN_MASK 0x0F > +#define LM3633_BL_RAMPDN_SHIFT 0 > + > +#define LM3633_REG_BL_RAMP_CONF 0x1B > +#define LM3633_BL_RAMP_MASK 0x0F > +#define LM3633_BL_RAMP_EACH 0x05 > + > +#define LM3633_REG_PTN0_RAMP 0x1C > +#define LM3633_REG_PTN1_RAMP 0x1D > +#define LM3633_PTN_RAMPUP_MASK 0x70 > +#define LM3633_PTN_RAMPUP_SHIFT 4 > +#define LM3633_PTN_RAMPDN_MASK 0x07 > +#define LM3633_PTN_RAMPDN_SHIFT 0 > + > +#define LM3633_REG_LED_MAPPING_MODE 0x1F > +#define LM3633_LED_EXPONENTIAL BIT(1) > + > +#define LM3633_REG_IMAX_HVLED_A 0x20 > +#define LM3633_REG_IMAX_HVLED_B 0x21 > +#define LM3633_REG_IMAX_LVLED_BASE 0x22 > + > +#define LM3633_REG_BL_FEEDBACK_ENABLE 0x28 > + > +#define LM3633_REG_ENABLE 0x2B > +#define LM3633_LED_BANK_OFFSET 2 > + > +#define LM3633_REG_PATTERN 0x2C > + > +#define LM3633_REG_BOOST_CFG 0x2D > +#define LM3633_OVP_MASK (BIT(1) | BIT(2)) > +#define LM3633_OVP_40V 0x6 > + > +#define LM3633_REG_PWM_CFG 0x2F > +#define LM3633_PWM_A_MASK BIT(0) > +#define LM3633_PWM_B_MASK BIT(1) > + > +#define LM3633_REG_BRT_HVLED_A_LSB 0x40 > +#define LM3633_REG_BRT_HVLED_A_MSB 0x41 > +#define LM3633_REG_BRT_HVLED_B_LSB 0x42 > +#define LM3633_REG_BRT_HVLED_B_MSB 0x43 > + > +#define LM3633_REG_BRT_LVLED_BASE 0x44 > + > +#define LM3633_REG_PTN_DELAY 0x50 > + > +#define LM3633_REG_PTN_LOWTIME 0x51 > + > +#define LM3633_REG_PTN_HIGHTIME 0x52 > + > +#define LM3633_REG_PTN_LOWBRT 0x53 > + > +#define LM3633_REG_PTN_HIGHBRT > LM3633_REG_BRT_LVLED_BASE > + > +#define LM3633_REG_BL_OPEN_FAULT_STATUS 0xB0 > + > +#define LM3633_REG_BL_SHORT_FAULT_STATUS 0xB2 > + > +#define LM3633_REG_MONITOR_ENABLE 0xB4 > + > +#define LM3633_MAX_REG 0xB4 > + > +/* LM3695 */ > +#define LM3695_REG_GP 0x10 > +#define LM3695_BL_CHANNEL_MASK BIT(3) > +#define LM3695_BL_DUAL_CHANNEL 0 > +#define LM3695_BL_SINGLE_CHANNEL BIT(3) > +#define LM3695_BRT_RW_MASK BIT(2) > +#define LM3695_BL_EN_MASK BIT(0) > + > +#define LM3695_REG_BRT_LSB 0x13 > +#define LM3695_REG_BRT_MSB 0x14 > + > +#define LM3695_MAX_REG 0x14 > + > +/* LM3697 */ > +#define LM3697_REG_HVLED_OUTPUT_CFG 0x10 > +#define LM3697_HVLED1_CFG_MASK BIT(0) > +#define LM3697_HVLED2_CFG_MASK BIT(1) > +#define LM3697_HVLED3_CFG_MASK BIT(2) > +#define LM3697_HVLED1_CFG_SHIFT 0 > +#define LM3697_HVLED2_CFG_SHIFT 1 > +#define LM3697_HVLED3_CFG_SHIFT 2 > + > +#define LM3697_REG_BL0_RAMP 0x11 > +#define LM3697_REG_BL1_RAMP 0x12 > +#define LM3697_RAMPUP_MASK 0xF0 > +#define LM3697_RAMPUP_SHIFT 4 > +#define LM3697_RAMPDN_MASK 0x0F > +#define LM3697_RAMPDN_SHIFT 0 > + > +#define LM3697_REG_RAMP_CONF 0x14 > +#define LM3697_RAMP_MASK 0x0F > +#define LM3697_RAMP_EACH 0x05 > + > +#define LM3697_REG_PWM_CFG 0x1C > +#define LM3697_PWM_A_MASK BIT(0) > +#define LM3697_PWM_B_MASK BIT(1) > + > +#define LM3697_REG_IMAX_A 0x17 > +#define LM3697_REG_IMAX_B 0x18 > + > +#define LM3697_REG_FEEDBACK_ENABLE 0x19 > + > +#define LM3697_REG_BRT_A_LSB 0x20 > +#define LM3697_REG_BRT_A_MSB 0x21 > +#define LM3697_REG_BRT_B_LSB 0x22 > +#define LM3697_REG_BRT_B_MSB 0x23 > + > +#define LM3697_REG_ENABLE 0x24 > + > +#define LM3697_REG_OPEN_FAULT_STATUS 0xB0 > + > +#define LM3697_REG_SHORT_FAULT_STATUS 0xB2 > + > +#define LM3697_REG_MONITOR_ENABLE 0xB4 > + > +#define LM3697_MAX_REG 0xB4 > +#endif > diff --git a/include/linux/mfd/ti-lmu.h b/include/linux/mfd/ti-lmu.h > new file mode 100644 > index 000000000000..09d5f30384e5 > --- /dev/null > +++ b/include/linux/mfd/ti-lmu.h > @@ -0,0 +1,87 @@ > +/* > + * TI LMU (Lighting Management Unit) Devices > + * > + * Copyright 2017 Texas Instruments > + * > + * Author: Milo Kim <milo....@ti.com> > + * > + * This program is free software; you can redistribute it and/or modify > + * it under the terms of the GNU General Public License version 2 as > + * published by the Free Software Foundation. > + */ > + > +#ifndef __MFD_TI_LMU_H__ > +#define __MFD_TI_LMU_H__ > + > +#include <linux/gpio.h> > +#include <linux/notifier.h> > +#include <linux/regmap.h> > + > +/* Notifier event */ > +#define LMU_EVENT_MONITOR_DONE 0x01 > + > +enum ti_lmu_id { > + LM3532, > + LM3631, > + LM3632, > + LM3633, > + LM3695, > + LM3697, > + LMU_MAX_ID, > +}; > + > +enum ti_lmu_max_current { > + LMU_IMAX_5mA, > + LMU_IMAX_6mA, > + LMU_IMAX_7mA = 0x03, > + LMU_IMAX_8mA, > + LMU_IMAX_9mA, > + LMU_IMAX_10mA = 0x07, > + LMU_IMAX_11mA, > + LMU_IMAX_12mA, > + LMU_IMAX_13mA, > + LMU_IMAX_14mA, > + LMU_IMAX_15mA = 0x0D, > + LMU_IMAX_16mA, > + LMU_IMAX_17mA, > + LMU_IMAX_18mA, > + LMU_IMAX_19mA, > + LMU_IMAX_20mA = 0x13, > + LMU_IMAX_21mA, > + LMU_IMAX_22mA, > + LMU_IMAX_23mA = 0x17, > + LMU_IMAX_24mA, > + LMU_IMAX_25mA, > + LMU_IMAX_26mA, > + LMU_IMAX_27mA = 0x1C, > + LMU_IMAX_28mA, > + LMU_IMAX_29mA, > + LMU_IMAX_30mA, > +}; > + > +enum lm363x_regulator_id { > + LM3631_BOOST, /* Boost output */ > + LM3631_LDO_CONT, /* Display panel controller */ > + LM3631_LDO_OREF, /* Gamma reference */ > + LM3631_LDO_POS, /* Positive display bias output */ > + LM3631_LDO_NEG, /* Negative display bias output */ > + LM3632_BOOST, /* Boost output */ > + LM3632_LDO_POS, /* Positive display bias output */ > + LM3632_LDO_NEG, /* Negative display bias output */ > +}; > + > +/** > + * struct ti_lmu > + * > + * @dev: Parent device pointer > + * @regmap: Used for i2c communcation on accessing registers > + * @en_gpio: GPIO for HWEN pin [Optional] > + * @notifier: Notifier for reporting hwmon event > + */ > +struct ti_lmu { > + struct device *dev; > + struct regmap *regmap; > + int en_gpio; > + struct blocking_notifier_head notifier; > +}; > +#endif -- Lee Jones Linaro STMicroelectronics Landing Team Lead Linaro.org │ Open source software for ARM SoCs Follow Linaro: Facebook | Twitter | Blog