于 2017年5月24日 GMT+08:00 下午3:30:19, Maxime Ripard <maxime.rip...@free-electrons.com> 写到: >On Tue, May 23, 2017 at 09:00:59PM +0800, icen...@aosc.io wrote: >> 在 2017-05-23 20:53,Maxime Ripard 写道: >> > On Mon, May 22, 2017 at 07:55:56PM +0200, Jernej Škrabec wrote: >> > > Hi, >> > > >> > > Dne sobota, 20. maj 2017 ob 03:37:53 CEST je Chen-Yu Tsai >napisal(a): >> > > > On Sat, May 20, 2017 at 2:23 AM, Jernej Škrabec ><jernej.skra...@siol.net> >> > > wrote: >> > > > > Hi, >> > > > > >> > > > > Dne petek, 19. maj 2017 ob 20:08:18 CEST je Icenowy Zheng >napisal(a): >> > > > >> 于 2017年5月20日 GMT+08:00 上午2:03:30, Maxime Ripard ><maxime.ripard@free- >> > > > > >> > > > > electrons.com> 写到: >> > > > >> >On Thu, May 18, 2017 at 12:43:50AM +0800, Icenowy Zheng >wrote: >> > > > >> >> Allwinner H3 features a TV encoder similar to the one in >earlier >> > > > >> > >> > > > >> >SoCs, >> > > > >> > >> > > > >> >> but with some different points about clocks: >> > > > >> >> - It has a mod clock and a bus clock. >> > > > >> >> - The mod clock must be at a fixed rate to generate >signal. >> > > > >> > >> > > > >> >Why? >> > > > >> >> > > > >> It's experiment result by Jernej. >> > > > >> >> > > > >> The clock rates in BSP kernel is also specially designed >> > > > >> (PLL_DE at 432MHz) in order to be able to feed the TVE. >> > > > > >> > > > > My experiments and search through BSP code showed that TVE >seems to have >> > > > > additional fixed predivider 8. So if you want to generate 27 >MHz clock, >> > > > > unit has to be feed with 216 MHz. >> > > > > >> > > > > TVE has only one PLL source PLL_DE. And since 216 MHz is a >bit low for >> > > > > DE2, >> > > > > BSP defaults to 432 MHz for PLL_DE and use divider 2 to >generate 216 MHz. >> > > > > This clock is then divided by 8 internaly to get final 27 >MHz. >> > > > > >> > > > > Please note that I don't have any hard evidence to support >that, only >> > > > > experimental data. However, only that explanation make sense >to me. >> > > > > >> > > > > BTW, BSP H3/H5 TV driver supports only PAL and NTSC which >both use 27 MHz >> > > > > base clock. Further experiments are needed to check if there >is any >> > > > > possibility to have other resolutions by manipulating clocks >and give >> > > > > other proper settings. I plan to do that, but not in very >near future. >> > > > >> > > > You only have composite video output, and those are the only 2 >standard >> > > > resolutions that make any sense. >> > > >> > > Right, other resolutions are for VGA. >> > > >> > > Anyway, I did some more digging in A10 and R40 datasheets. I >think >> > > that H3 TVE >> > > unit is something in between. R40 TVE has a setting to select "up >> > > sample". >> > >> > That might be just another translation of oversampling :) >> > >> > I didn't know it could be applied to composite signals though, but >I >> > guess this is just another analog signal after all. >> > >> > > Possible settings are 27 MHz, 54 MHz, 108 MHz and 216 MHz. BSP >> > > driver on R40 >> > > has this setting enabled only for PAL and NTSC and it is always >216 >> > > MHz. I >> > > think that H3 may have this hardwired to 216 MHz and this would >be >> > > the reason >> > > why 216 MHz is needed. >> > > >> > > Has anyone else any better explanation? >> > >> > That's already a pretty good one. >> > >> > Either way, wether this is upsampling, oversampling or just a >> > pre-divider, this can and should be dealt with in the mode_set >> > callback, and not in the probe. >> >> I got a better idea -- let TVE driver have the CLK_TVE as an >> input and create a subclock output with divider 16, and feed this >> subclock to TCON lcd-ch1. >> >> This is a model of the real hardware -- the clock divider is in >> TVE, not TCON. > >That's definitely not a good representation of the hardware. There's >one clock, it goes to the TCON, period.
No, I still think it goes to the TVE as: 1. it's named TVE in datasheet. 2. Generating signal with such a low resolution but such a high dotclock is not a good situation. > >However, the TV encoder has a constraint on that clock rate. This can >be easily implemented using a custom encoder state where you'd set the >multiplier to set on that clock, and the TCON will use it. > >Maxime