On 01-06-17 09:44, Hegr, Jiri wrote:
> Dears,
> We use small WiFi evaluation board WM-BN-BM-04_EVB_V1.2 with BCM43362 chip
> (Broadcom).
> This board is connected to OMAP-L138 via SDIO interface with Linux 4.9.10
> containing WiFi driver brcmfmac.
> Our problem is in OOB interrupt. The driver (and the WiFi chip) works fine if
> the interrupt is not set in a device tree (SDIO interface is used instead).
> But if the host-wake interrupt is used, the initialization phase does not
> pass. We are sure that the OOB interrupt is triggered. We found out that it
> waits for a control frame (probably) but it gets some event frame only. After
> about 2.5 seconds the timeout occurs and the initialization fails.
> Could you help us to solve the problem?
> There is our device tree settings and terminal output bellow (the "DBG" lines
> are our own).
>
> There is also problem with WARN_ON(nents > sdiodev->max_segment_count); in
> bcmsdh.c file, but it seems that it does not influence the driver work
> because the problem occurs without OOB interrupt setting also and everything
> works fine.
>
> Regards,
>
> Jiri Hegr
>
> mmc1: mmc@21b000 {
> #address-cells = <1>;
> #size-cells = <0>;
> max-frequency = <25000000>;
> bus-width = <4>;
> pinctrl-names = "default";
> pinctrl-0 = <&mmc1_pins>;
> status = "okay";
> non-removable;
>
> brcmf: bcrmf@1 {
> reg = <1>;
> compatible = "brcm,bcm4329-fmac";
> interrupt-parent = <&gpio>;
> interrupts = <95 0x02>;
> interrupt-names = "host-wake";
> };
> };
>
> [ 24.314527] brcmfmac: *** DBG: starting datawork worker thread...
> [ 24.354778] brcmfmac: *** DBG: brcmf_sdio_readframes...
> [ 24.360088] brcmfmac: *** DBG: rd->len check: 0
> [ 24.404232] brcmfmac: *** DBG: rd->channel check: 1
> [ 24.435047] brcmfmac: *** DBG: rd->len check: 0
> [ 24.454977] brcmfmac: *** DBG: brcmf_sdio_readframes - loop break
> [ 27.013900] brcmfmac: brcmf_sdio_bus_rxctl: resumed on timeout
> [ 27.019813] brcmfmac: brcmf_c_preinit_dcmds: Retreiving cur_etheraddr
> failed, -110
> [ 27.031282] brcmfmac: brcmf_bus_start: failed: -110
> [ 27.046164] brcmfmac: brcmf_sdio_firmware_callback: dongle is not
> responding
Can you build the driver with CONFIG_BRCMDBG and load the driver with
debugging:
$ sudo insmod brcmfmac.ko debug=0x31516
Regards,
Arend
> Honeywell *
> Jiri Hegr - R&D Scientist III.
>
> Honeywell International s.r.o. - Aerospace Advanced Techonologies
> V Parku 2325/16
> Praha 148 00, Czech Republic
> Office: Turanka 100
> 627 00 Brno, Czech Republic
>
> Tel: +420 532 115 564
> E-mail: jiri.he...@honeywell.com<mailto:jiri.he...@honeywell.com>
>
>
