On 06/11/2017 10:18 PM, Martin Blumenstingl wrote: > On Sat, Jun 10, 2017 at 12:37 AM, Martin Blumenstingl > <martin.blumensti...@googlemail.com> wrote: >> Hi Neil, >> >> On Fri, Jun 9, 2017 at 11:49 AM, Neil Armstrong <narmstr...@baylibre.com> >> wrote: >>> Switch to the stable UART bindings by adding a XTAL node and using the >>> proper compatible strings. >> unfortunately this won't apply now that Kevin has merged my "ARM: dts: >> meson8: add and use the real clock controller" >> on the other hand this will make the patch easier as you can now do >> the same changes as in meson8b.dtsi > Neil, if you want you could also drop this from your series and let me > handle this (just let me know). I would even go one step further and > export the CLKID_UART0, CLKID_UART1 and CLKID_UART2 gates and pass > them as "pclk" for uart_{A,B,C} > I'll even *try* to test if this works on real hardware (my Meson8m2 > board has a RTL8723BS SDIO wifi + bluetooth chip - wifi driver support > has been pretty bad so far - but I'll try to see if I can get and > messages out of the bluetooth part) > just let me know if you want me to handle this patch for you
No in fact it was just a "PoC" to show how to handle it on non-gx DTS. I'm ok to leave it to you when the UART code is merged. Neil > >>> Signed-off-by: Neil Armstrong <narmstr...@baylibre.com> >>> --- >>> arch/arm/boot/dts/meson8.dtsi | 23 +++++++++++++++++++---- >>> 1 file changed, 19 insertions(+), 4 deletions(-) >>> >>> diff --git a/arch/arm/boot/dts/meson8.dtsi b/arch/arm/boot/dts/meson8.dtsi >>> index 6993077..a2ea112 100644 >>> --- a/arch/arm/boot/dts/meson8.dtsi >>> +++ b/arch/arm/boot/dts/meson8.dtsi >>> @@ -83,6 +83,13 @@ >>> }; >>> }; >>> >>> + xtal: xtal-clk { >>> + compatible = "fixed-clock"; >>> + clock-frequency = <24000000>; >>> + clock-output-names = "xtal"; >>> + #clock-cells = <0>; >>> + }; >>> + >>> clk81: clk@0 { >>> #clock-cells = <0>; >>> compatible = "fixed-clock"; >>> @@ -199,17 +206,25 @@ >>> }; >>> >>> &uart_AO { >>> - clocks = <&clk81>; >>> + compatible = "amlogic,meson8-uart", "amlogic,meson-ao-uart"; >>> + clocks = <&xtal>, <&clk81>, <&clk81>; >>> + clock-names = "xtal", "pclk", "baud"; >>> }; >>> >>> &uart_A { >>> - clocks = <&clk81>; >>> + compatible = "amlogic,meson8-uart"; >>> + clocks = <&xtal>, <&clk81>, <&clk81>; >>> + clock-names = "xtal", "pclk", "baud"; >>> }; >>> >>> &uart_B { >>> - clocks = <&clk81>; >>> + compatible = "amlogic,meson8-uart"; >>> + clocks = <&xtal>, <&clk81>, <&clk81>; >>> + clock-names = "xtal", "pclk", "baud"; >>> }; >>> >>> &uart_C { >>> - clocks = <&clk81>; >>> + compatible = "amlogic,meson8-uart"; >>> + clocks = <&xtal>, <&clk81>, <&clk81>; >>> + clock-names = "xtal", "pclk", "baud"; >>> }; >>> -- >>> 1.9.1 >>> >>> >>> _______________________________________________ >>> linux-amlogic mailing list >>> linux-amlo...@lists.infradead.org >>> http://lists.infradead.org/mailman/listinfo/linux-amlogic