On 06/27/2017 07:18 PM, matthew.gerl...@linux.intel.com wrote: > > > On Tue, 27 Jun 2017, Marek Vasut wrote: > >> On 06/27/2017 05:57 PM, matthew.gerl...@linux.intel.com wrote: >>> >>> >>> On Tue, 27 Jun 2017, Marek Vasut wrote: >>> >>>> On 06/27/2017 04:32 PM, matthew.gerl...@linux.intel.com wrote: >>>>> >>>>> >>>>> On Tue, 27 Jun 2017, Marek Vasut wrote: >>>>> >>>>> Hi Marek, >>>>> >>>>> Thanks for the feedback. See my comments below. >>>>> >>>>> Matthew Gerlach >>>>> >>>>>> On 06/26/2017 06:13 PM, matthew.gerl...@linux.intel.com wrote: >>>>>>> From: Matthew Gerlach <matthew.gerl...@linux.intel.com> >>>>>>> >>>>>>> Device Tree bindings for Version 2 of the Altera Quadspi Controller >>>>>>> that can be optionally paired with a windowed bridge. >>>>>>> >>>>>>> Signed-off-by: Matthew Gerlach <matthew.gerl...@linux.intel.com> >>>>>>> --- >>>>>>> .../devicetree/bindings/mtd/altera-quadspi-v2.txt | 37 >>>>>>> ++++++++++++++++++++++ >>>>>>> 1 file changed, 37 insertions(+) >>>>>>> create mode 100644 >>>>>>> Documentation/devicetree/bindings/mtd/altera-quadspi-v2.txt >>>>>>> >>>>>>> diff --git >>>>>>> a/Documentation/devicetree/bindings/mtd/altera-quadspi-v2.txt >>>>>>> b/Documentation/devicetree/bindings/mtd/altera-quadspi-v2.txt >>>>>>> new file mode 100644 >>>>>>> index 0000000..8ba63d7 >>>>>>> --- /dev/null >>>>>>> +++ b/Documentation/devicetree/bindings/mtd/altera-quadspi-v2.txt >>>>>>> @@ -0,0 +1,37 @@ >>>>>>> +* Altera Quad SPI Controller Version 2 >>>>>>> + >>>>>>> +Required properties: >>>>>>> +- compatible : Should be "altr,quadspi-v2". >>>>>>> +- reg : Contains at least two entries, and possibly three entries, >>>>>>> each of >>>>>>> + which is a tuple consisting of a physical address and length. >>>>>>> +- reg-names : Should contain the names "avl_csr" and "avl_mem" >>>>>>> corresponding >>>>>>> + to the control and status registers and qspi memory, >>>>>>> respectively. >>>>>>> + >>>>>>> + >>>>>>> +The Altera Quad SPI Controller Version 2 can be paired with a >>>>>>> windowed bridge >>>>>>> +in order to reduce the footprint of the memory interface. When a >>>>>>> windowed >>>>>>> +bridge is used, reads and writes of data must be 32 bits wide. >>>>>>> + >>>>>>> +Optional properties: >>>>>>> +- reg-names : Should contain the name "avl_window", if the windowed >>>>>>> bridge >>>>>>> + is used. This name corresponds to the register space >>>>>>> that >>>>>>> + controls the window. >>>>>>> +- window-size : The size of the window which must be an even power >>>>>>> of 2. >>>>>>> +- read-bit-reverse : A boolean indicating the data read from the >>>>>>> flash should >>>>>>> + be bit reversed on a byte by byte basis before being >>>>>>> + delivered to the MTD layer. >>>>>>> +- write-bit-reverse : A boolean indicating the data written to the >>>>>>> flash should >>>>>>> + be bit reversed on a byte by byte basis. >>>>>> >>>>>> Is there ever a usecase where you need to set just one of these >>>>>> props ? >>>>>> Also, they're altera specific, so altr, prefix should be added. >>>>> >>>>> In general, I think if bit reversal is required, it would be >>>>> required in >>>>> both directions. However, anything is possible when using FPGAs. So >>>>> I thought separate booleans would be future proofing the bindings. >>>> >>>> Maybe we should drop this whole thing and add it when this is actually >>>> required. >>>> >>>> Are there any users of this in the wild currently ? >>>> >>>> What is the purpose of doing this per-byte bit reverse instead of >>>> storing th bits in the original order ? >>> >>> Hi Marek, >>> >>> Yes, there is hardware that has been in the wild for years that needs >>> this bit reversal. The specific use case is when a flash chip is >>> connected to >>> a FPGA, and the contents of the flash is used to configure the FPGA on >>> power up. In this use case, there is no processor involved with >>> configuring the FPGA. I am most familiar with this feature/bug with >>> Altera FPGAs, but I believe this issue exists with other programmable >>> devices. >> >> So the EPCQ/EPCS flash stores the bitstream in reverse or something ? >> What are you storing in that flash except for the bitstream, filesystem? >> Feel free to go into details, I believe it'd be useful to know exactly >> what the problem is you're trying to solve here. > > Hi Marek, > > I am trying to write an MTD/spi-nor driver for version 2 of the > Altera Quadspi contoller. This controller is soft IP that is deployed > in a FPGA. As such, this component/driver can be used in wide range of > use cases. The controller could be used to update EPCQ/EPCS flash > stores containing bit streams, but this component could be used for > flash for filesystems or any non-volatile data store. My hope is that > all possible use cases should be covered by this driver.
How does this particular case where you have to reverse the bits look like ? >>>>> Thinking about this binding more, I wonder if the binding name(s) >>>>> should be (read|write)-bit8-reverse to indicate reversings the bits >>>>> in a byte as opposed to reversing the bits in a 32 bit word? >>>>> >>>>> I don't think bit reversal is specific to Altera/Intel components. >>>>> I see >>>>> a nand driver performing bit reversal, and I think I've recently seen >>>>> other FPGA based drivers requiring bit reversal. >>>> >>>> $ git grep bit.reverse Documentation/devicetree/ | wc -l >>>> 0 >>>> >>>> So we don't have such a generic binding . It's up to Rob (I guess) to >>>> decide whether this is SoC specific and should've altr, prefix or not. >>>> IMO it is. >>> >>> I agree there is no generic binding at this time, and I look forward >>> to any input from Rob and anyone else on this issue. I think it is >>> worth pointing out that this really isn't an issue of an SoC, but rather >>> it is an >>> issue of how data in the flash chip is accessed.I think what makes >>> this issue >>> "weird" is that we have different hardware accessing the data in the >>> flash with a different perspective. The FPGA looks at the data from one >>> perspective on power up, and a processor trying to update the flash has >>> a different perspective. >> >> Another thing I'd ask here is, is that bit-reverse a hardware property >> or is that some software configuration thing ? > > I would say the bit reversal is a property of the FPGA that is reading > the flash at power up. So it's not a property of the block, but rather of the bus somewhere ? -- Best regards, Marek Vasut