On 08/02/2017 05:17 PM, Franklin S Cooper Jr wrote:
This patch adds PM runtime support to the I2C Davinci driver.
Reviewed-by: Grygorii Strashko <grygorii.stras...@ti.com>
Signed-off-by: Franklin S Cooper Jr <fcoo...@ti.com>
Signed-off-by: Sekhar Nori <nsek...@ti.com>
---
drivers/i2c/busses/i2c-davinci.c | 61 ++++++++++++++++++++++++++++++++++------
1 file changed, 53 insertions(+), 8 deletions(-)
diff --git a/drivers/i2c/busses/i2c-davinci.c b/drivers/i2c/busses/i2c-davinci.c
index 5749aac..62ff869 100644
--- a/drivers/i2c/busses/i2c-davinci.c
+++ b/drivers/i2c/busses/i2c-davinci.c
@@ -36,6 +36,7 @@
#include <linux/gpio.h>
#include <linux/of_device.h>
#include <linux/platform_data/i2c-davinci.h>
+#include <linux/pm_runtime.h>
/* ----- global defines ----------------------------------------------- */
@@ -122,6 +123,9 @@
/* set the SDA GPIO low */
#define DAVINCI_I2C_DCLR_PDCLR1 BIT(1)
+/* timeout for pm runtime autosuspend */
+#define DAVINCI_I2C_PM_TIMEOUT 1000 /* ms */
+
struct davinci_i2c_dev {
struct device *dev;
void __iomem *base;
@@ -541,10 +545,17 @@ i2c_davinci_xfer(struct i2c_adapter *adap, struct i2c_msg
msgs[], int num)
dev_dbg(dev->dev, "%s: msgs: %d\n", __func__, num);
+ ret = pm_runtime_get_sync(dev->dev);
+ if (ret < 0) {
+ dev_err(dev->dev, "Failed to runtime_get device: %d\n", ret);
+ pm_runtime_put_noidle(dev->dev);
+ return ret;
+ }
+
ret = i2c_davinci_wait_bus_not_busy(dev);
if (ret < 0) {
dev_warn(dev->dev, "timeout waiting for bus ready\n");
- return ret;
+ goto out;
}
for (i = 0; i < num; i++) {
@@ -552,14 +563,19 @@ i2c_davinci_xfer(struct i2c_adapter *adap, struct i2c_msg
msgs[], int num)
dev_dbg(dev->dev, "%s [%d/%d] ret: %d\n", __func__, i + 1, num,
ret);
if (ret < 0)
- return ret;
+ goto out;
}
+ ret = num;
#ifdef CONFIG_CPU_FREQ
complete(&dev->xfr_complete);
#endif
- return num;
+out:
+ pm_runtime_mark_last_busy(dev->dev);
+ pm_runtime_put_autosuspend(dev->dev);
+
+ return ret;
}
static u32 i2c_davinci_func(struct i2c_adapter *adap)
@@ -599,6 +615,9 @@ static irqreturn_t i2c_davinci_isr(int this_irq, void
*dev_id)
int count = 0;
u16 w;
+ if (pm_runtime_suspended(dev->dev))
+ return IRQ_NONE;
+
while ((stat = davinci_i2c_read_reg(dev, DAVINCI_I2C_IVR_REG))) {
dev_dbg(dev->dev, "%s: stat=0x%x\n", __func__, stat);
if (count++ == 100) {
@@ -802,7 +821,6 @@ static int davinci_i2c_probe(struct platform_device *pdev)
dev->clk = devm_clk_get(&pdev->dev, NULL);
if (IS_ERR(dev->clk))
return PTR_ERR(dev->clk);
- clk_prepare_enable(dev->clk);
mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
dev->base = devm_ioremap_resource(&pdev->dev, mem);
@@ -811,6 +829,17 @@ static int davinci_i2c_probe(struct platform_device *pdev)
goto err_unuse_clocks;
}
+ pm_runtime_enable(dev->dev);
+ pm_runtime_set_autosuspend_delay(dev->dev,
+ DAVINCI_I2C_PM_TIMEOUT);
+ pm_runtime_use_autosuspend(dev->dev);
Pls, move autosuspend configuration before pm_runtime_enable()
+
+ r = pm_runtime_get_sync(dev->dev);
+ if (r < 0) {
+ dev_err(dev->dev, "failed to runtime_get device: %d\n", r);
+ goto err_unuse_clocks;
+ }
+
Otherwise looks good to me.
--
regards,
-grygorii
