[+cc Christoph] On Tue, Aug 15, 2017 at 05:54:27PM +0300, Meelis Roos wrote: > I noticed that in 4.13.0-rc4 there is a new error in dmesg on my sparc64 > t5120 server: can't allocate MSI-X affinity masks. > > [ 30.274284] qla2xxx [0000:00:00.0]-0005: : QLogic Fibre Channel HBA > Driver: 10.00.00.00-k. > [ 30.274648] qla2xxx [0000:10:00.0]-001d: : Found an ISP2432 irq 21 iobase > 0x000000c100d00000. > [ 30.275447] qla2xxx 0000:10:00.0: can't allocate MSI-X affinity masks for > 2 vectors > [ 30.816882] scsi host1: qla2xxx > [ 30.877294] qla2xxx: probe of 0000:10:00.0 failed with error -22 > [ 30.877578] qla2xxx [0000:10:00.1]-001d: : Found an ISP2432 irq 22 iobase > 0x000000c100d04000. > [ 30.878387] qla2xxx 0000:10:00.1: can't allocate MSI-X affinity masks for > 2 vectors > [ 31.367083] scsi host1: qla2xxx > [ 31.427500] qla2xxx: probe of 0000:10:00.1 failed with error -22 > > I do not know if the driver works since nothing is attached to the FC > HBA at the moment, but from the error messages it looks like the driver > fails to load. > > I booted 4.12 and 4.11 - the red error is not there but the failure > seems to be the same error -22:
-22 is -EINVAL, so not very specific. Many failures probably use this code. There were several IRQ affinity changes between v4.12 and v4.13; it'll probably be obvious to Christoph. > [2478900.385223] qla2xxx [0000:00:00.0]-0005: : QLogic Fibre Channel HBA > Driver: 9.00.00.00-k. > [2478900.385610] qla2xxx [0000:10:00.0]-001d: : Found an ISP2432 irq 21 > iobase 0x000000c100d00000. > [2478900.930517] scsi host1: qla2xxx > [2478900.990939] qla2xxx: probe of 0000:10:00.0 failed with error -22 > [2478900.991222] qla2xxx [0000:10:00.1]-001d: : Found an ISP2432 irq 22 > iobase 0x000000c100d04000. > [2478901.510715] scsi host1: qla2xxx > [2478901.581106] qla2xxx: probe of 0000:10:00.1 failed with error -22 > > Will try older kernels too if it is useful for bisection. > > On an older sparc64 (t1-200) with 4.13.0-rc4, qla2xxx loads fine (nothing is > attached there either): > > [ 30.590064] qla2xxx [0000:00:00.0]-0005: : QLogic Fibre Channel HBA > Driver: 10.00.00.00-k. > [ 30.699053] PCI: Enabling device: (0000:02:05.0), cmd 3 > [ 30.699122] qla2xxx [0000:02:05.0]-001d: : Found an ISP2200 irq 12 iobase > 0x000001ff0000a000. > [ 52.463403] scsi host2: qla2xxx > [ 52.545973] qla2xxx [0000:02:05.0]-4800:2: DPC handler sleeping. > [ 52.627163] qla2xxx [0000:02:05.0]-00fb:2: QLogic QLA22xx - . > [ 52.705428] qla2xxx [0000:02:05.0]-00fc:2: ISP2200: PCI (33 MHz) @ > 0000:02:05.0 hdma- host#=2 fw=2.02.08 TP. > [ 53.503221] qla2xxx [0000:02:05.0]-480f:2: Loop resync scheduled. > [ 73.796964] qla2xxx [0000:02:05.0]-8038:2: Cable is unplugged... > [ 73.876036] qla2xxx [0000:02:05.0]-883a:2: fw_state=4 (ffff, ffff, ffff, > ffff ffff) curr time=ffffa61d. > [ 73.999845] qla2xxx [0000:02:05.0]-286c:2: qla2x00_loop_resync *** FAILED > ***. > [ 74.094861] qla2xxx [0000:02:05.0]-4810:2: Loop resync end. > [ 74.168188] qla2xxx [0000:02:05.0]-4800:2: DPC handler sleeping. > > > -- > Meelis Roos (mr...@linux.ee)
