The QorIQ LX2160A processor is built in the 16FFC process on
the Layerscape architecture combining sixteen ARM A72 processor
cores with advanced, high-performance datapath acceleration and
network, peripheral interfaces required for networking, wireless
infrastructure, storage, and general-purpose embedded applications.

Features summary:
    - Sixteen 32-bit / 64-bit ARM v8 A72 CPUs
    - Cache Coherent Interconnect Fabric (CCN508 aka “Eliot”)
    - Two 64-bit 3.2GT/s DDR4 SDRAM memory controllers with ECC.
    - Data path acceleration architecture (DPAA2)
    - 24 Serdes lanes at up to 25 GHz
    - Ethernet interfaces
      Single WRIOP tile supporting 130Gbps using 18 MACs
      Support for 10G-SXGMII (aka USXGMII).
      Support for SGMII (and 1000Base-KX)
      Support for XFI (and 10GBase-KR)
      Support for CAUI4 (100G); CAUI2 (50G) and 25G-AUI(25G).
      Support for XLAUI4 (and 40GBase-KR4) for 40G.
      Support for two RGMII parallel interfaces.
      Energy efficient Ethernet support (802.3az)
      IEEE 1588 support.
    - High-speed peripheral interfaces
      Two PCIe Gen 4.0 8-lane controllers supporting SR-IOV,
      Four PCIe Gen 4.0 4-lane controllers.
      Four serial ATA (SATA 3.0) controllers.
      Two USB 3.0 controllers with integrated PHY
      Two Enhanced secure digital host controllers
      Two Controller Area Network (CAN) modules
      Flexible Serial peripheral interface (FlexSPI) controller.
      Three Serial peripheral interface (SPI) controllers.
      Nine I2C Controllers.
      Four UARTs supporting two 4-pin UART ports or four 2-pin UART ports.
      General Purpose IO (GPIO)
    - Support for hardware virtualization and partitioning (ARM MMU-500)
    - Support for GIC (ARM GIC-500)
    - QorIQ platform Trust Architecture 3.0
    - One Secure WatchDog timer and one Non-Secure Watchdog timer.
    - ARM Generic Timer
    - Two Flextimers
    - Debug supporting run control, data acquisition, high-speed trace,
      performance/event monitoring
    - Thermal Monitor Unit (TMU) with +/- 2C accuracy
    - Support for Voltage ID (VID) for yield improvement

Signed-off-by: Sriram Dash <sriram.d...@nxp.com>
---
 Documentation/devicetree/bindings/arm/fsl.txt  |   8 +
 arch/arm64/boot/dts/freescale/Makefile         |   1 +
 arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi | 240 +++++++++++++++++++++++++
 arch/arm64/boot/dts/freescale/fsl-lx2qds1.dts  |  54 ++++++
 4 files changed, 303 insertions(+)
 create mode 100644 arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi
 create mode 100644 arch/arm64/boot/dts/freescale/fsl-lx2qds1.dts

diff --git a/Documentation/devicetree/bindings/arm/fsl.txt 
b/Documentation/devicetree/bindings/arm/fsl.txt
index cdb9dd7..6069434 100644
--- a/Documentation/devicetree/bindings/arm/fsl.txt
+++ b/Documentation/devicetree/bindings/arm/fsl.txt
@@ -218,3 +218,11 @@ Required root node properties:
 LS2088A ARMv8 based RDB Board
 Required root node properties:
     - compatible = "fsl,ls2088a-rdb", "fsl,ls2088a";
+
+LX2160A SoC
+Required root node properties:
+    - compatible = "fsl,lx2160a";
+
+LX2160A ARMv8 based QDS Board
+Required root node properties:
+    - compatible = "fsl,lx2qds1", "fsl,lx2160a";
diff --git a/arch/arm64/boot/dts/freescale/Makefile 
b/arch/arm64/boot/dts/freescale/Makefile
index 72c4b52..634f6d4 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -12,6 +12,7 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-rdb.dtb
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-simu.dtb
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2088a-qds.dtb
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2088a-rdb.dtb
+dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2qds1.dtb
  
 always         := $(dtb-y)
 subdir-y       := $(dts-dirs)
diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi 
b/arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi
new file mode 100644
index 0000000..48874cf
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi
@@ -0,0 +1,240 @@
+/*
+ * Device Tree Include file for Layerscape-LX2160A family SoC.
+ *
+ * Copyright 2017 NXP
+ *
+ * Sriram Dash <sriram.d...@nxp.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPLv2 or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This library is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This library is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/memreserve/ 0x80000000 0x00010000;
+
+/ {
+       compatible = "fsl,lx2160a";
+       interrupt-parent = <&gic>;
+       #address-cells = <2>;
+       #size-cells = <2>;
+
+       cpus {
+               #address-cells = <1>;
+               #size-cells = <0>;
+
+               /* We have 8 clusters having 2 Cortex-A72 cores each */
+               cpu@0 {
+                       device_type = "cpu";
+                       compatible = "arm,cortex-a72";
+                       reg = <0x0>;
+               };
+
+               cpu@1 {
+                       device_type = "cpu";
+                       compatible = "arm,cortex-a72";
+                       reg = <0x1>;
+               };
+
+               cpu@100 {
+                       device_type = "cpu";
+                       compatible = "arm,cortex-a72";
+                       reg = <0x100>;
+               };
+
+               cpu@101 {
+                       device_type = "cpu";
+                       compatible = "arm,cortex-a72";
+                       reg = <0x101>;
+               };
+
+               cpu@200 {
+                       device_type = "cpu";
+                       compatible = "arm,cortex-a72";
+                       reg = <0x200>;
+               };
+
+               cpu@201 {
+                       device_type = "cpu";
+                       compatible = "arm,cortex-a72";
+                       reg = <0x201>;
+               };
+
+               cpu@300 {
+                       device_type = "cpu";
+                       compatible = "arm,cortex-a72";
+                       reg = <0x300>;
+               };
+
+               cpu@301 {
+                       device_type = "cpu";
+                       compatible = "arm,cortex-a72";
+                       reg = <0x301>;
+               };
+
+               cpu@400 {
+                       device_type = "cpu";
+                       compatible = "arm,cortex-a72";
+                       reg = <0x400>;
+               };
+
+               cpu@401 {
+                       device_type = "cpu";
+                       compatible = "arm,cortex-a72";
+                       reg = <0x401>;
+               };
+
+               cpu@500 {
+                       device_type = "cpu";
+                       compatible = "arm,cortex-a72";
+                       reg = <0x500>;
+               };
+
+               cpu@501 {
+                       device_type = "cpu";
+                       compatible = "arm,cortex-a72";
+                       reg = <0x501>;
+               };
+
+               cpu@600 {
+                       device_type = "cpu";
+                       compatible = "arm,cortex-a72";
+                       reg = <0x600>;
+               };
+
+               cpu@601 {
+                       device_type = "cpu";
+                       compatible = "arm,cortex-a72";
+                       reg = <0x601>;
+               };
+
+               cpu@700 {
+                       device_type = "cpu";
+                       compatible = "arm,cortex-a72";
+                       reg = <0x700>;
+               };
+
+               cpu@701 {
+                       device_type = "cpu";
+                       compatible = "arm,cortex-a72";
+                       reg = <0x701>;
+               };
+
+       };
+
+       memory@80000000 {
+               device_type = "memory";
+               reg = <0x00000000 0x80000000 0 0x80000000>;
+                     /* DRAM space - 1, size : 2 GB DRAM */
+       };
+
+       sysclk: sysclk {
+               compatible = "fixed-clock";
+               #clock-cells = <0>;
+               clock-frequency = <100000000>;
+               clock-output-names = "sysclk";
+       };
+
+       gic: interrupt-controller@6000000 {
+               compatible = "arm,gic-v3";
+               reg = <0x0 0x06000000 0 0x10000>, /* GIC Dist */
+                     <0x0 0x06200000 0 0x200000>, /*GICR(RD_base + SGI_base)*/
+                     <0x0 0x0c0c0000 0 0x2000>, /* GICC */
+                     <0x0 0x0c0d0000 0 0x1000>, /* GICH */
+                     <0x0 0x0c0e0000 0 0x20000>; /* GICV */
+               #interrupt-cells = <3>;
+               #address-cells = <2>;
+               #size-cells = <2>;
+               ranges;
+               interrupt-controller;
+               interrupts = <1 9 0x4>;
+
+               its: gic-its@6020000 {
+                       compatible = "arm,gic-v3-its";
+                       msi-controller;
+                       reg = <0x0 0x6020000 0 0x20000>;
+               };
+       };
+
+       timer {
+               compatible = "arm,armv8-timer";
+               interrupts = <1 13 4>, /* Physical Secure PPI, active-low */
+                            <1 14 4>, /* Physical Non-Secure PPI, active-low */
+                            <1 11 4>, /* Virtual PPI, active-low */
+                            <1 10 4>; /* Hypervisor PPI, active-low */
+       };
+
+       soc {
+               compatible = "simple-bus";
+               #address-cells = <2>;
+               #size-cells = <2>;
+               ranges;
+
+               uart0: serial@21c0000 {
+                       device_type = "serial";
+                       compatible = "arm,pl011","arm,sbsa-uart";
+                       reg = <0x0 0x21c0000 0x0 0x1000>;
+                       interrupts = <0 32 0x4>;
+                       current-speed = <115200>;
+               };
+
+               uart1: serial@21d0000 {
+                       device_type = "serial";
+                       compatible = "arm,pl011","arm,sbsa-uart";
+                       reg = <0x0 0x21d0000 0x0 0x1000>;
+                       interrupts = <0 33 0x4>;
+                       current-speed = <115200>;
+               };
+
+               uart2: serial@21e0000 {
+                       device_type = "serial";
+                       compatible = "arm,pl011","arm,sbsa-uart";
+                       reg = <0x0 0x21e0000 0x0 0x1000>;
+                       interrupts = <0 72 0x4>;
+                       current-speed = <115200>;
+               };
+
+               uart3: serial@21f0000 {
+                       device_type = "serial";
+                       compatible = "arm,pl011","arm,sbsa-uart";
+                       reg = <0x0 0x21f0000 0x0 0x1000>;
+                       interrupts = <0 73 0x4>;
+                       current-speed = <115200>;
+               };
+       };
+};
diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2qds1.dts 
b/arch/arm64/boot/dts/freescale/fsl-lx2qds1.dts
new file mode 100644
index 0000000..0a8f525
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/fsl-lx2qds1.dts
@@ -0,0 +1,54 @@
+/*
+ * Device Tree file for LX2 QDS1 Board
+ *
+ * Copyright 2017 NXP
+ *
+ * Sriram Dash <sriram.d...@nxp.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This library is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This library is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include "fsl-lx2160a.dtsi"
+
+/ {
+       model = "NXP Layerscape LX2 QDS1 Board";
+       compatible = "fsl,lx2qds1", "fsl,lx2160a";
+};
-- 
1.9.1

Reply via email to