On Thu, Sep 14, 2017 at 11:43:18AM +0800, Sandy Huang wrote:
> This path add support rv1108 rgb output interface driver.
>
> Signed-off-by: Sandy Huang <h...@rock-chips.com>
> ---
> .../bindings/display/rockchip/rockchip-rgb.txt | 80
> ++++++++++++++++++++++
> 1 file changed, 80 insertions(+)
> create mode 100644
> Documentation/devicetree/bindings/display/rockchip/rockchip-rgb.txt
>
> diff --git
> a/Documentation/devicetree/bindings/display/rockchip/rockchip-rgb.txt
> b/Documentation/devicetree/bindings/display/rockchip/rockchip-rgb.txt
> new file mode 100644
> index 0000000..4164512
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/display/rockchip/rockchip-rgb.txt
> @@ -0,0 +1,80 @@
> +Rockchip RV1108 RGB interface
> +================================
> +
> +Required properties:
> +- compatible: matching the soc type:
> + - "rockchip,rv1108-rgb";
> +
> +Optional properties:
> +- pinctrl-names: must contain a "lcdc" entry.
> +- pinctrl-0: pin control group to be used for this interface.
> +
> +Required nodes:
> +- rockchip,rgb-mode: should be "p888", "p666", "p565", "s888", "s888-dummy"
This should be a standard property. Any device with a parallel interface
is going to need something like this.
> + - p888: output r8-g8-b8 at each dclk cycle for per-pixel
> + - p666: output r6-g6-b6 at each dclk cycle for per-pixel
> + - p565: output r5-g6-b5 at each dclk cycle for per-pixel
> + - s888: output r8-g8-b8 in three dclk cycle for per-pixel
> + - s888-dmmy: output r8-g8-b8-dummy in four dclk cycle for per-pixel
> +
> +The rgb has two video ports described by:
> + Documentation/devicetree/bindings/media/video-interfaces.txt
> +Their connections are modeled using the OF graph bindings specified in
> + Documentation/devicetree/bindings/graph.txt.
> +
> +- video port 0 for the VOP input, the remote endpoint maybe vopb/vopl/vop
> +- video port 1 for either a panel or subsequent encoder
> +
> +the panel described by:
> + Documentation/devicetree/bindings/display/panel/simple-panel.txt
> +Panel other required properties:
> +- ports for remote rgb output.
> +
> +Example:
> +
> +panel: panel {
> + compatible = "auo,b101ean01";
> + enable-gpios = <&gpio7 21 GPIO_ACTIVE_HIGH>;
> +
> + ports {
> + panel_in_rgb: endpoint {
> + remote-endpoint = <&rgb_out_panel>;
> + };
> + };
> +};
> +
> +For Rockchip RV1108:
> +
> + rgb: rgb {
> + compatible = "rockchip,rv1108-rgb";
> + pinctrl-names = "lcdc";
> + pinctrl-0 = <&lcdc_ctl>;
> + rockchip,rgb-mode = "p888";
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + rgb_in: port@0 {
> + reg = <0>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + rgb_in_vop: endpoint@0 {
> + reg = <0>;
Don't need reg for a single endpoint.
> + remote-endpoint = <&vop_out_rgb>;
> + };
> + };
> +
> + rgb_out: port@1 {
> + reg = <1>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + rgb_out_panel: endpoint@0 {
> + reg = <0>;
ditto.
> + remote-endpoint = <&panel_in_rgb>;
> + };
> + };
> + };
> + };
> --
> 2.7.4
>
>
