From: Ravi Eluri <venkatarav...@techveda.org>
Cleaned up device tree.
Signed-off-by: Ravi Eluri <venkatarav...@techveda.org>
Signed-off-by: Suniel Mahesh <suni...@techveda.org>
---
Note:
- This is the fourth patch of the four patch series.
- Patch was compile tested and built(ARCH=arm, imx28) on linux-next
(latest).
- No build issues reported.
- Please discard this changeset, if this is not making any better.
---
arch/arm/boot/dts/imx28-evk.dts | 448 ++++++++++++++++++++--------------------
1 file changed, 224 insertions(+), 224 deletions(-)
diff --git a/arch/arm/boot/dts/imx28-evk.dts b/arch/arm/boot/dts/imx28-evk.dts
index 9d74486..eb683264 100644
--- a/arch/arm/boot/dts/imx28-evk.dts
+++ b/arch/arm/boot/dts/imx28-evk.dts
@@ -121,249 +121,249 @@
};
};
- &gpmi {
- pinctrl-names = "default";
- pinctrl-0 = <&gpmi_pins_a &gpmi_status_cfg
- &gpmi_pins_evk>;
- status = "okay";
- };
+&gpmi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpmi_pins_a &gpmi_status_cfg
+ &gpmi_pins_evk>;
+ status = "okay";
+};
- &ssp0 {
- compatible = "fsl,imx28-mmc";
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_8bit_pins_a
- &mmc0_cd_cfg &mmc0_sck_cfg>;
- bus-width = <8>;
- wp-gpios = <&gpio2 12 0>;
- vmmc-supply = <®_vddio_sd0>;
- status = "okay";
- };
+&ssp0 {
+ compatible = "fsl,imx28-mmc";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_8bit_pins_a
+ &mmc0_cd_cfg &mmc0_sck_cfg>;
+ bus-width = <8>;
+ wp-gpios = <&gpio2 12 0>;
+ vmmc-supply = <®_vddio_sd0>;
+ status = "okay";
+};
- &ssp1 {
- compatible = "fsl,imx28-mmc";
- bus-width = <8>;
- wp-gpios = <&gpio0 28 0>;
- };
+&ssp1 {
+ compatible = "fsl,imx28-mmc";
+ bus-width = <8>;
+ wp-gpios = <&gpio0 28 0>;
+};
- &ssp2 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,imx28-spi";
- pinctrl-names = "default";
- pinctrl-0 = <&spi2_pins_a>;
- status = "okay";
-
- flash: m25p80@0 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "sst,sst25vf016b",
"jedec,spi-nor";
- spi-max-frequency = <40000000>;
- reg = <0>;
- };
- };
+&ssp2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx28-spi";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi2_pins_a>;
+ status = "okay";
- &pinctrl {
- pinctrl-names = "default";
- pinctrl-0 = <&hog_pins_a>;
-
- hog_pins_a: hog@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_SSP1_CMD__GPIO_2_13
- MX28_PAD_SSP1_DATA3__GPIO_2_15
- MX28_PAD_ENET0_RX_CLK__GPIO_4_13
- MX28_PAD_SSP1_SCK__GPIO_2_12
- MX28_PAD_PWM3__GPIO_3_28
- MX28_PAD_LCD_RESET__GPIO_3_30
- MX28_PAD_AUART2_RX__GPIO_3_8
- MX28_PAD_AUART2_TX__GPIO_3_9
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
-
- led_pin_gpio3_5: led_gpio3_5@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_AUART1_TX__GPIO_3_5
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
-
- gpmi_pins_evk: gpmi-nand-evk@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_GPMI_CE1N__GPMI_CE1N
- MX28_PAD_GPMI_RDY1__GPMI_READY1
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
-
- lcdif_pins_evk: lcdif-evk@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_LCD_RD_E__LCD_VSYNC
- MX28_PAD_LCD_WR_RWN__LCD_HSYNC
- MX28_PAD_LCD_RS__LCD_DOTCLK
- MX28_PAD_LCD_CS__LCD_ENABLE
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
- };
+ flash: m25p80@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "sst,sst25vf016b", "jedec,spi-nor";
+ spi-max-frequency = <40000000>;
+ reg = <0>;
+ };
+};
- &lcdif {
- pinctrl-names = "default";
- pinctrl-0 = <&lcdif_24bit_pins_a
- &lcdif_pins_evk>;
- lcd-supply = <®_lcd_3v3>;
- display = <&display0>;
- status = "okay";
-
- display0: display0 {
- bits-per-pixel = <32>;
- bus-width = <24>;
-
- display-timings {
- native-mode = <&timing0>;
- timing0: timing0 {
- clock-frequency =
<33500000>;
- hactive = <800>;
- vactive = <480>;
- hback-porch = <89>;
- hfront-porch = <164>;
- vback-porch = <23>;
- vfront-porch = <10>;
- hsync-len = <10>;
- vsync-len = <10>;
- hsync-active = <0>;
- vsync-active = <0>;
- de-active = <1>;
- pixelclk-active = <0>;
- };
- };
- };
- };
+&pinctrl {
+ pinctrl-names = "default";
+ pinctrl-0 = <&hog_pins_a>;
+
+ hog_pins_a: hog@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_SSP1_CMD__GPIO_2_13
+ MX28_PAD_SSP1_DATA3__GPIO_2_15
+ MX28_PAD_ENET0_RX_CLK__GPIO_4_13
+ MX28_PAD_SSP1_SCK__GPIO_2_12
+ MX28_PAD_PWM3__GPIO_3_28
+ MX28_PAD_LCD_RESET__GPIO_3_30
+ MX28_PAD_AUART2_RX__GPIO_3_8
+ MX28_PAD_AUART2_TX__GPIO_3_9
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
- &can0 {
- pinctrl-names = "default";
- pinctrl-0 = <&can0_pins_a>;
- xceiver-supply = <®_can_3v3>;
- status = "okay";
- };
+ led_pin_gpio3_5: led_gpio3_5@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_AUART1_TX__GPIO_3_5
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
- &can1 {
- pinctrl-names = "default";
- pinctrl-0 = <&can1_pins_a>;
- xceiver-supply = <®_can_3v3>;
- status = "okay";
- };
+ gpmi_pins_evk: gpmi-nand-evk@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_GPMI_CE1N__GPMI_CE1N
+ MX28_PAD_GPMI_RDY1__GPMI_READY1
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
- &saif0 {
- pinctrl-names = "default";
- pinctrl-0 = <&saif0_pins_a>;
- status = "okay";
- };
+ lcdif_pins_evk: lcdif-evk@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_LCD_RD_E__LCD_VSYNC
+ MX28_PAD_LCD_WR_RWN__LCD_HSYNC
+ MX28_PAD_LCD_RS__LCD_DOTCLK
+ MX28_PAD_LCD_CS__LCD_ENABLE
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+};
- &saif1 {
- pinctrl-names = "default";
- pinctrl-0 = <&saif1_pins_a>;
- fsl,saif-master = <&saif0>;
- status = "okay";
+&lcdif {
+ pinctrl-names = "default";
+ pinctrl-0 = <&lcdif_24bit_pins_a
+ &lcdif_pins_evk>;
+ lcd-supply = <®_lcd_3v3>;
+ display = <&display0>;
+ status = "okay";
+
+ display0: display0 {
+ bits-per-pixel = <32>;
+ bus-width = <24>;
+
+ display-timings {
+ native-mode = <&timing0>;
+ timing0: timing0 {
+ clock-frequency = <33500000>;
+ hactive = <800>;
+ vactive = <480>;
+ hback-porch = <89>;
+ hfront-porch = <164>;
+ vback-porch = <23>;
+ vfront-porch = <10>;
+ hsync-len = <10>;
+ vsync-len = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
};
+ };
+ };
+};
- &lradc {
- status = "okay";
- fsl,lradc-touchscreen-wires = <4>;
- fsl,ave-ctrl = <4>;
- fsl,ave-delay = <2>;
- fsl,settling = <10>;
- };
+&can0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&can0_pins_a>;
+ xceiver-supply = <®_can_3v3>;
+ status = "okay";
+};
- &i2c0 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
- status = "okay";
-
- sgtl5000: codec@a {
- compatible = "fsl,sgtl5000";
- reg = <0x0a>;
- VDDA-supply = <®_3p3v>;
- VDDIO-supply = <®_3p3v>;
- clocks = <&saif0>;
- };
-
- at24@51 {
- compatible = "atmel,24c32";
- pagesize = <32>;
- reg = <0x51>;
- };
- };
+&can1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&can1_pins_a>;
+ xceiver-supply = <®_can_3v3>;
+ status = "okay";
+};
- &pwm {
- pinctrl-names = "default";
- pinctrl-0 = <&pwm2_pins_a>;
- status = "okay";
- };
+&saif0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&saif0_pins_a>;
+ status = "okay";
+};
- &duart {
- pinctrl-names = "default";
- pinctrl-0 = <&duart_pins_a>;
- status = "okay";
- };
+&saif1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&saif1_pins_a>;
+ fsl,saif-master = <&saif0>;
+ status = "okay";
+};
- &auart0 {
- pinctrl-names = "default";
- pinctrl-0 = <&auart0_pins_a>;
- uart-has-rtscts;
- status = "okay";
- };
+&lradc {
+ status = "okay";
+ fsl,lradc-touchscreen-wires = <4>;
+ fsl,ave-ctrl = <4>;
+ fsl,ave-delay = <2>;
+ fsl,settling = <10>;
+};
- &auart3 {
- pinctrl-names = "default";
- pinctrl-0 = <&auart3_pins_a>;
- status = "okay";
- };
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+
+ sgtl5000: codec@a {
+ compatible = "fsl,sgtl5000";
+ reg = <0x0a>;
+ VDDA-supply = <®_3p3v>;
+ VDDIO-supply = <®_3p3v>;
+ clocks = <&saif0>;
+ };
- &usbphy0 {
- status = "okay";
- };
+ at24@51 {
+ compatible = "atmel,24c32";
+ pagesize = <32>;
+ reg = <0x51>;
+ };
+};
- &usbphy1 {
- status = "okay";
- };
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm2_pins_a>;
+ status = "okay";
+};
- &usb0 {
- pinctrl-names = "default";
- pinctrl-0 = <&usb0_id_pins_a>;
- vbus-supply = <®_usb0_vbus>;
- status = "okay";
- };
+&duart {
+ pinctrl-names = "default";
+ pinctrl-0 = <&duart_pins_a>;
+ status = "okay";
+};
- &usb1 {
- vbus-supply = <®_usb1_vbus>;
- status = "okay";
- };
+&auart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&auart0_pins_a>;
+ uart-has-rtscts;
+ status = "okay";
+};
- &mac0 {
- phy-mode = "rmii";
- pinctrl-names = "default";
- pinctrl-0 = <&mac0_pins_a>;
- phy-supply = <®_fec_3v3>;
- phy-reset-gpios = <&gpio4 13 GPIO_ACTIVE_LOW>;
- phy-reset-duration = <100>;
- status = "okay";
- };
+&auart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&auart3_pins_a>;
+ status = "okay";
+};
- &mac1 {
- phy-mode = "rmii";
- pinctrl-names = "default";
- pinctrl-0 = <&mac1_pins_a>;
- status = "okay";
- };
+&usbphy0 {
+ status = "okay";
+};
+
+&usbphy1 {
+ status = "okay";
+};
+
+&usb0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb0_id_pins_a>;
+ vbus-supply = <®_usb0_vbus>;
+ status = "okay";
+};
+
+&usb1 {
+ vbus-supply = <®_usb1_vbus>;
+ status = "okay";
+};
+
+&mac0 {
+ phy-mode = "rmii";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mac0_pins_a>;
+ phy-supply = <®_fec_3v3>;
+ phy-reset-gpios = <&gpio4 13 GPIO_ACTIVE_LOW>;
+ phy-reset-duration = <100>;
+ status = "okay";
+};
+
+&mac1 {
+ phy-mode = "rmii";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mac1_pins_a>;
+ status = "okay";
+};
--
1.9.1
