DRA72 uses USB3 PHY for the 2nd lane of PCIE. The configuration required to make USB3 PHY used for the 2nd lane of PCIe is done here.
Signed-off-by: Kishon Vijay Abraham I <[email protected]> --- drivers/phy/ti/phy-ti-pipe3.c | 47 +++++++++++++++++++++++++++++++++++++------ 1 file changed, 41 insertions(+), 6 deletions(-) diff --git a/drivers/phy/ti/phy-ti-pipe3.c b/drivers/phy/ti/phy-ti-pipe3.c index 68ce4a082b9b..d5a7cc435fb7 100644 --- a/drivers/phy/ti/phy-ti-pipe3.c +++ b/drivers/phy/ti/phy-ti-pipe3.c @@ -56,6 +56,12 @@ #define SATA_PLL_SOFT_RESET BIT(18) +#define PHY_RX_ANA_PRGRAMMABILITY_REG 0xC +#define MEM_EN_PLLBYP BIT(7) + +#define PHY_TX_TEST_CONFIG 0x2C +#define MEM_ENTESTCLK BIT(31) + #define PIPE3_PHY_PWRCTL_CLK_CMD_MASK 0x003FC000 #define PIPE3_PHY_PWRCTL_CLK_CMD_SHIFT 14 @@ -110,6 +116,10 @@ #define PLL_IDLE_TIME 100 /* in milliseconds */ #define PLL_LOCK_TIME 100 /* in milliseconds */ +#define PIPE3_PHY_DISABLE_SYNC_POWER BIT(4) + +#define CONFIGURE_AS_PCIE BIT(0) + struct pipe3_dpll_params { u16 m; u8 n; @@ -141,6 +151,7 @@ struct ti_pipe3 { unsigned int power_reg; /* power reg. index within syscon */ unsigned int pcie_pcs_reg; /* pcs reg. index in syscon */ bool sata_refclk_enabled; + u32 flags; }; static struct pipe3_dpll_map dpll_map_usb[] = { @@ -233,11 +244,22 @@ static int ti_pipe3_power_on(struct phy *x) rate = rate / 1000000; mask = OMAP_CTRL_PIPE3_PHY_PWRCTL_CLK_CMD_MASK | OMAP_CTRL_PIPE3_PHY_PWRCTL_CLK_FREQ_MASK; - val = PIPE3_PHY_TX_RX_POWERON << PIPE3_PHY_PWRCTL_CLK_CMD_SHIFT; + val = PIPE3_PHY_TX_RX_POWERON; + if (phy->flags & CONFIGURE_AS_PCIE) + val |= PIPE3_PHY_DISABLE_SYNC_POWER; + val <<= PIPE3_PHY_PWRCTL_CLK_CMD_SHIFT; val |= rate << OMAP_CTRL_PIPE3_PHY_PWRCTL_CLK_FREQ_SHIFT; ret = regmap_update_bits(phy->phy_power_syscon, phy->power_reg, mask, val); + + if (phy->flags & CONFIGURE_AS_PCIE) { + ret = regmap_update_bits(phy->phy_power_syscon, phy->power_reg, + mask, val); + if (ret < 0) + return ret; + } + return ret; } @@ -335,6 +357,19 @@ static int ti_pipe3_init(struct phy *x) int ret = 0; ti_pipe3_enable_clocks(phy); + + if (phy->flags & CONFIGURE_AS_PCIE) { + val = ti_pipe3_readl(phy->phy_rx, + PHY_RX_ANA_PRGRAMMABILITY_REG); + val |= MEM_EN_PLLBYP; + ti_pipe3_writel(phy->phy_rx, PHY_RX_ANA_PRGRAMMABILITY_REG, + val); + val = ti_pipe3_readl(phy->phy_tx, PHY_TX_TEST_CONFIG); + val |= MEM_ENTESTCLK; + ti_pipe3_writel(phy->phy_tx, PHY_TX_TEST_CONFIG, val); + return 0; + } + /* * Set pcie_pcs register to 0x96 for proper functioning of phy * as recommended in AM572x TRM SPRUHZ6, section 18.5.2.2, table @@ -395,7 +430,8 @@ static int ti_pipe3_exit(struct phy *x) return 0; /* PCIe doesn't have internal DPLL */ - if (!of_device_is_compatible(phy->dev->of_node, "ti,phy-pipe3-pcie")) { + if (!of_device_is_compatible(phy->dev->of_node, "ti,phy-pipe3-pcie") && + !(phy->flags & CONFIGURE_AS_PCIE)) { /* Put DPLL in IDLE mode */ val = ti_pipe3_readl(phy->pll_ctrl_base, PLL_CONFIGURATION2); val |= PLL_IDLE; @@ -589,12 +625,8 @@ static int ti_pipe3_get_tx_rx_base(struct ti_pipe3 *phy) { struct resource *res; struct device *dev = phy->dev; - struct device_node *node = dev->of_node; struct platform_device *pdev = to_platform_device(dev); - if (!of_device_is_compatible(node, "ti,phy-pipe3-pcie")) - return 0; - res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "phy_rx"); phy->phy_rx = devm_ioremap_resource(dev, res); @@ -666,6 +698,9 @@ static int ti_pipe3_probe(struct platform_device *pdev) if (ret) return ret; + if (of_property_read_bool(node, "ti,configure-as-pcie")) + phy->flags |= CONFIGURE_AS_PCIE; + platform_set_drvdata(pdev, phy); pm_runtime_enable(dev); -- 2.11.0
