On Sun, 13 May 2007 01:43:42 -0600
Grant Likely <[EMAIL PROTECTED]> wrote:
>
> Here is the 3rd iteration with the following changes:
> - Modified to be an i2c "new style" driver based on David Brownell's work
> - uses the new prototype for i2c_smbus_read_i2c_block_data() for block data
> reads instead of a single byte at a time.
>
> drivers/i2c/chips/ds1682.c | 270
> ++++++++++++++++++++++++++++++++++++++++++++
> 1 files changed, 270 insertions(+), 0 deletions(-)
This version of the patch omitted the changes to drivers/i2c/chips/Kconfig
and drivers/i2c/chips/Makefile, which I assume was accidental.
As usual, I generated the delta so we can see what was done:
From: Grant Likely <[EMAIL PROTECTED]>
- Modified to be an i2c "new style" driver based on David Brownell's work
- uses the new prototype for i2c_smbus_read_i2c_block_data() for block data
reads instead of a single byte at a time.
Signed-off-by: Grant Likely <[EMAIL PROTECTED]>
Cc: Jean Delvare <[EMAIL PROTECTED]>
Signed-off-by: Andrew Morton <[EMAIL PROTECTED]>
---
drivers/i2c/chips/ds1682.c | 333 ++++++++++++-----------------------
1 files changed, 121 insertions(+), 212 deletions(-)
diff -puN
drivers/i2c/chips/ds1682.c~i2c-add-driver-for-dallas-ds1682-elapsed-time-recorder-update
drivers/i2c/chips/ds1682.c
---
a/drivers/i2c/chips/ds1682.c~i2c-add-driver-for-dallas-ds1682-elapsed-time-recorder-update
+++ a/drivers/i2c/chips/ds1682.c
@@ -16,132 +16,106 @@
/*
* The DS1682 elapsed timer recorder is a simple device that implements
- * one elapsed time counters, one event counter, an alarm signal and 10
+ * one elapsed time counter, one event counter, an alarm signal and 10
* bytes of general purpose EEPROM.
*
* This driver provides access to the DS1682 counters and user data via
* the sysfs. The following attributes are added to the device node:
- * elapsed_time (u32): Total elapsed event time in 1/4s resolution
+ * elapsed_time (u32): Total elapsed event time in ms resolution
* alarm_time (u32): When elapsed time exceeds the value in alarm_time,
* then the alarm pin is asserted.
* event_count (u16): number of times the event pin has gone low.
- * user_data (u8[10]): general purpose EEPROM
+ * eeprom (u8[10]): general purpose EEPROM
*
* Counter registers and user data are both read/write unless the device
- * has been write protected. This driver does not support turning on write
+ * has been write protected. This driver does not support turning off write
* protection. Once write protection is turned on, it is impossible to
- * turn off so I have left the feature out of this driver to avoid
+ * turn it off again, so I have left the feature out of this driver to avoid
* accidental enabling, but it is trivial to add write protect support.
*
*/
-#include <linux/device.h>
#include <linux/module.h>
#include <linux/init.h>
#include <linux/slab.h>
#include <linux/i2c.h>
#include <linux/string.h>
-#include <linux/bcd.h>
#include <linux/list.h>
#include <linux/sysfs.h>
#include <linux/ctype.h>
+#include <linux/hwmon-sysfs.h>
/* Device registers */
-#define DS1682_ADDR 0x6B
-
#define DS1682_REG_CONFIG 0x00
#define DS1682_REG_ALARM 0x01
#define DS1682_REG_ELAPSED 0x05
#define DS1682_REG_EVT_CNTR 0x09
-#define DS1682_REG_USER_DATA 0x0b
+#define DS1682_REG_EEPROM 0x0b
#define DS1682_REG_RESET 0x1d
#define DS1682_REG_WRITE_DISABLE 0x1e
#define DS1682_REG_WRITE_MEM_DISABLE 0x1f
-/*
- * Probing class
- */
-static unsigned short normal_i2c[] = { DS1682_ADDR, I2C_CLIENT_END };
-
-I2C_CLIENT_INSMOD;
-
-/*
- * Low level chip access functions
- */
-static int ds1682_read(struct i2c_client *client, int reg, void *buf, int len)
-{
- u8 *bytes = buf;
- int val;
-
- while (len--) {
- val = i2c_smbus_read_byte_data(client, reg++);
- if (val < 0)
- return -EIO;
- *bytes++ = val;
- }
- return 0;
-}
+#define DS1682_EEPROM_SIZE 10
/*
* Generic counter attributes
*/
-static int ds1682_attr_to_reg(struct device_attribute *attr, int *regsize);
-
-static ssize_t ds1682_show(struct device *dev,
- struct device_attribute *attr, char *buf)
+static ssize_t ds1682_show(struct device *dev, struct device_attribute *attr,
+ char *buf)
{
- u32 val = 0;
- int reg;
- int regsize;
-
- dev_dbg(dev, "ds1682_show() called for %s\n", attr->attr.name);
-
- /* Get the register address */
- reg = ds1682_attr_to_reg(attr, ®size);
- if (reg < 0)
- return -EIO;
+ struct sensor_device_attribute_2 *sattr = to_sensor_dev_attr_2(attr);
+ struct i2c_client *client = to_i2c_client(dev);
+ __le32 val = 0;
+ int rc;
+
+ dev_dbg(dev, "ds1682_show() called on %s\n", attr->attr.name);
/* Read the register */
- if (ds1682_read(to_i2c_client(dev), reg, &val, regsize))
+ rc = i2c_smbus_read_i2c_block_data(client, sattr->index, sattr->nr,
+ (u8 *) & val);
+ if (rc < 0)
return -EIO;
+ /* Special case: the 32 bit regs are time values with 1/4s
+ * resolution, scale them up to milliseconds */
+ if (sattr->nr == 4)
+ return sprintf(buf, "%lli\n", ((u64) le32_to_cpu(val)) * 250);
+
/* Format the output string and return # of bytes */
- return sprintf(buf, "0x%.2x\n", le32_to_cpu(val));
+ return sprintf(buf, "%li\n", (long)le32_to_cpu(val));
}
-static ssize_t ds1682_store(struct device *dev,
- struct device_attribute *attr, const char *buf,
- size_t count)
+static ssize_t ds1682_store(struct device *dev, struct device_attribute *attr,
+ const char *buf, size_t count)
{
+ struct sensor_device_attribute_2 *sattr = to_sensor_dev_attr_2(attr);
struct i2c_client *client = to_i2c_client(dev);
- int reg;
- int regsize;
char *endp;
- u32 val;
+ u64 val;
+ __le32 val_le;
int rc;
- /* Sanitize the input */
- reg = ds1682_attr_to_reg(attr, ®size);
-
- if ((reg < 0) || (count >= 16) || (buf[count] != '\0')) {
- dev_dbg(dev, "insane input; reg=0x%i count=%zd%s\n",
- reg, count, buf[count] == '\0' ? " unterminated" : "");
- return -EIO;
- }
+ dev_dbg(dev, "ds1682_store() called on %s\n", attr->attr.name);
/* Decode input */
- val = simple_strtoul(buf, &endp, 0);
+ val = simple_strtoull(buf, &endp, 0);
if (buf == endp) {
dev_dbg(dev, "input string not a number\n");
return -EIO;
}
+ /* Special case: the 32 bit regs are time values with 1/4s
+ * resolution, scale input down to quarter-seconds */
+ if (sattr->nr == 4)
+ do_div(val, 250);
+
/* write out the value */
- val = cpu_to_le32(val);
- rc = i2c_smbus_write_i2c_block_data(client, reg, regsize, (void *)&val);
+ val_le = cpu_to_le32(val);
+ rc = i2c_smbus_write_i2c_block_data(client, sattr->index, sattr->nr,
+ (u8 *) & val);
if (rc < 0) {
dev_err(dev, "register write failed; reg=0x%x, size=%i\n",
- reg, regsize);
+ sattr->index, sattr->nr);
return -EIO;
}
@@ -151,196 +125,131 @@ static ssize_t ds1682_store(struct devic
/*
* Simple register attributes
*/
-DEVICE_ATTR(config, S_IRUGO, ds1682_show, NULL);
-DEVICE_ATTR(elapsed_time, S_IRUGO | S_IWUSR, ds1682_show, ds1682_store);
-DEVICE_ATTR(alarm_time, S_IRUGO | S_IWUSR, ds1682_show, ds1682_store);
-DEVICE_ATTR(event_count, S_IRUGO | S_IWUSR, ds1682_show, ds1682_store);
-
-/* Get register size and address from device_attribute structure. This
- * function must come after the DEVICE_ATTR() lines as it depends on the
- * device_attribute lines being declared */
-static int ds1682_attr_to_reg(struct device_attribute *attr, int *regsize)
-{
- if (attr == &dev_attr_elapsed_time) {
- *regsize = 4;
- return DS1682_REG_ELAPSED;
- }
-
- if (attr == &dev_attr_alarm_time) {
- *regsize = 4;
- return DS1682_REG_ALARM;
- }
-
- if (attr == &dev_attr_event_count) {
- *regsize = 2;
- return DS1682_REG_EVT_CNTR;
- }
-
- if (attr == &dev_attr_config) {
- *regsize = 1;
- return DS1682_REG_CONFIG;
- }
-
- pr_debug("Cannot find registers for device_attribute %p\n", attr);
- return -ENODEV;
-}
+SENSOR_DEVICE_ATTR_2(config, S_IRUGO, ds1682_show, NULL, DS1682_REG_CONFIG, 1);
+SENSOR_DEVICE_ATTR_2(elapsed_time, S_IRUGO | S_IWUSR, ds1682_show,
ds1682_store,
+ 4, DS1682_REG_ELAPSED);
+SENSOR_DEVICE_ATTR_2(alarm_time, S_IRUGO | S_IWUSR, ds1682_show, ds1682_store,
+ 4, DS1682_REG_ALARM);
+SENSOR_DEVICE_ATTR_2(event_count, S_IRUGO | S_IWUSR, ds1682_show, ds1682_store,
+ 2, DS1682_REG_EVT_CNTR);
+
+static const struct attribute_group ds1682_group = {
+ .attrs = (struct attribute *[]) {
+ &sensor_dev_attr_config.dev_attr.attr,
+ &sensor_dev_attr_elapsed_time.dev_attr.attr,
+ &sensor_dev_attr_alarm_time.dev_attr.attr,
+ &sensor_dev_attr_event_count.dev_attr.attr,
+ NULL,
+ },
+};
/*
* User data attribute
*/
-static ssize_t ds1682_user_data_show(struct device *dev,
- struct device_attribute *attr, char *buf)
+static ssize_t ds1682_eeprom_read(struct kobject *kobj, char *buf, loff_t off,
+ size_t count)
{
- char *end = buf;
- u8 val[10];
- int i;
+ struct i2c_client *client = kobj_to_i2c_client(kobj);
+ int rc;
- if (ds1682_read(to_i2c_client(dev), DS1682_REG_USER_DATA, &val, 10))
- return -EIO;
+ dev_dbg(&client->dev, "ds1682_eeprom_read(p=%p, off=%lli, c=%zi)\n",
+ buf, off, count);
- for (i = 0; i < 10; i++)
- end += sprintf(end, "%.2x ", val[i]);
+ if (off > DS1682_EEPROM_SIZE)
+ return 0;
- *(end - 1) = '\n'; /* Eliminate trailing space */
- return end - buf;
+ if (off + count > DS1682_EEPROM_SIZE)
+ count = DS1682_EEPROM_SIZE - off;
+
+ rc = i2c_smbus_read_i2c_block_data(client, DS1682_REG_EEPROM + off,
+ count, buf);
+ if (rc < 0)
+ return -EIO;
+
+ return count;
}
-static ssize_t ds1682_user_data_store(struct device *dev,
- struct device_attribute *attr,
- const char *buf, size_t count)
+static ssize_t ds1682_eeprom_write(struct kobject *kobj, char *buf, loff_t off,
+ size_t count)
{
- u8 data[10];
- char *endp;
- int bytecount = 0;
-
- /* Check input for sanity */
- if ((count >= 80) || (buf[count] != '\0')) {
- dev_dbg(dev, "insane input; count=%zd%s\n",
- count, buf[count] == '\0' ? " unterminated" : "");
- return -EIO;
- }
+ struct i2c_client *client = kobj_to_i2c_client(kobj);
- /* Parse the data */
- while (bytecount < 10) {
- while (isspace(*buf))
- buf++;
-
- data[bytecount] = simple_strtoul(buf, &endp, 16);
- if (endp == buf) /* make sure it's a real data value */
- break;
+ dev_dbg(&client->dev, "ds1682_eeprom_write(p=%p, off=%lli, c=%zi)\n",
+ buf, off, count);
- buf = endp;
- bytecount++;
- }
- while (isspace(*endp))
- endp++;
+ if (off >= DS1682_EEPROM_SIZE)
+ return -ENOSPC;
- /* Abort on invalid data */
- if ((bytecount == 0) || (*endp != '\0')) {
- dev_dbg(dev, "invalid input *buf=\"%s\" *endp=\"%s\"\n",
- buf, endp);
- return -EIO;
- }
+ if (off + count > DS1682_EEPROM_SIZE)
+ count = DS1682_EEPROM_SIZE - off;
/* Write out to the device */
- if (i2c_smbus_write_i2c_block_data(to_i2c_client(dev),
- DS1682_REG_USER_DATA, bytecount,
- data) < 0)
+ if (i2c_smbus_write_i2c_block_data(client, DS1682_REG_EEPROM + off,
+ count, buf) < 0)
return -EIO;
+
return count;
}
-DEVICE_ATTR(user_data, S_IRUGO | S_IWUSR, ds1682_user_data_show,
- ds1682_user_data_store);
+static struct bin_attribute ds1682_eeprom_attr = {
+ .attr = {
+ .name = "eeprom",
+ .mode = S_IRUGO | S_IWUSR,
+ .owner = THIS_MODULE,
+ },
+ .size = DS1682_EEPROM_SIZE,
+ .read = ds1682_eeprom_read,
+ .write = ds1682_eeprom_write,
+};
/*
* Called when a device is found at the ds1682 address
*/
-static struct i2c_driver ds1682_driver;
-static int ds1682_detect(struct i2c_adapter *adapter, int address, int kind)
+static int ds1682_probe(struct i2c_client *client)
{
- struct i2c_client *new_client;
int err = 0;
- if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA |
- I2C_FUNC_I2C))
- goto exit;
+ if (client->addr != 0x6b) {
+ dev_err(&client->dev, "%x is not a valid address\n",
+ client->addr);
+ return -ENODEV;
+ }
- if (!(new_client = kzalloc(sizeof(struct i2c_client), GFP_KERNEL))) {
- err = -ENOMEM;
+ if (!i2c_check_functionality(client->adapter,
+ I2C_FUNC_SMBUS_READ_BYTE_DATA |
+ I2C_FUNC_SMBUS_WRITE_I2C_BLOCK)) {
+ dev_err(&client->dev, "i2c bus does not support the ds1682\n");
goto exit;
}
- new_client->addr = address;
- new_client->adapter = adapter;
- new_client->driver = &ds1682_driver;
- new_client->flags = 0;
-
- /* Note: Ignoring 'kind' value as the ds1682 uses a fixed address */
-
- /* We can fill in the remaining client fields */
- strlcpy(new_client->name, "ds1682", I2C_NAME_SIZE);
-
- /* Tell the I2C layer a new client has arrived */
- if ((err = i2c_attach_client(new_client)))
- goto exit_free;
-
- if (device_create_file(&new_client->dev, &dev_attr_config))
- goto exit_attr_config;
- if (device_create_file(&new_client->dev, &dev_attr_elapsed_time))
- goto exit_attr_elapsed;
- if (device_create_file(&new_client->dev, &dev_attr_alarm_time))
- goto exit_attr_alarm;
- if (device_create_file(&new_client->dev, &dev_attr_event_count))
- goto exit_attr_event;
- if (device_create_file(&new_client->dev, &dev_attr_user_data))
- goto exit_attr_userdata;
+ if (sysfs_create_group(&client->dev.kobj, &ds1682_group))
+ goto exit;
+
+ if (sysfs_create_bin_file(&client->dev.kobj, &ds1682_eeprom_attr))
+ goto exit_bin_attr;
return 0;
- exit_attr_userdata:
- device_remove_file(&new_client->dev, &dev_attr_event_count);
- exit_attr_event:
- device_remove_file(&new_client->dev, &dev_attr_alarm_time);
- exit_attr_alarm:
- device_remove_file(&new_client->dev, &dev_attr_elapsed_time);
- exit_attr_elapsed:
- device_remove_file(&new_client->dev, &dev_attr_config);
- exit_attr_config:
- i2c_detach_client(new_client);
- exit_free:
- kfree(new_client);
+ exit_bin_attr:
+ sysfs_remove_group(&client->dev.kobj, &ds1682_group);
exit:
return err;
}
-static int ds1682_attach_adapter(struct i2c_adapter *adapter)
+static int ds1682_remove(struct i2c_client *client)
{
- return i2c_probe(adapter, &addr_data, ds1682_detect);
-}
-
-static int ds1682_detach_client(struct i2c_client *client)
-{
- int err;
- device_remove_file(&client->dev, &dev_attr_user_data);
- device_remove_file(&client->dev, &dev_attr_event_count);
- device_remove_file(&client->dev, &dev_attr_alarm_time);
- device_remove_file(&client->dev, &dev_attr_elapsed_time);
- device_remove_file(&client->dev, &dev_attr_config);
-
- if ((err = i2c_detach_client(client)))
- return err;
+ sysfs_remove_bin_file(&client->dev.kobj, &ds1682_eeprom_attr);
+ sysfs_remove_group(&client->dev.kobj, &ds1682_group);
- kfree(client);
return 0;
}
static struct i2c_driver ds1682_driver = {
.driver = {
- .name = "ds1682",
- },
- .attach_adapter = ds1682_attach_adapter,
- .detach_client = ds1682_detach_client,
+ .name = "ds1682",
+ },
+ .probe = ds1682_probe,
+ .remove = ds1682_remove,
};
static int __init ds1682_init(void)
_
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [EMAIL PROTECTED]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
