Following the form:
[1.] PROBLEM: Kernel Oops 10% of diskless boots
[2.] When booting a diskless workstation (etherboot) the boot will fail
with an Oops, roughly 10% of the time. This has remained the failure
rate for quite some time. The included Oops if from 2.4.0-test12-pre4.
Similar crashing is seen with Intel, as well as AMD (below). Maybe
something is uninitialized in the case of root on NFS???
[3.] diskless boot oops nfsroot
[4.] 2.4.0-test12 (pre4)
[5.]
Kernel command line: auto rw root=/dev/nfs nfsroot=/diskless/%s
console=ttyS0,9600 ramdisk
_size=6144 ip=192.168.15.82:192.168.15.55:192.168.15.1:255.255.255.0:
Initializing CPU#0
Detected 901.614 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 1795.69 BogoMIPS
Memory: 123820k/131008k available (1872k kernel code, 6800k reserved,
136k data, 220k init
, 0k highmem)
Dentry-cache hash table entries: 16384 (order: 5, 131072 bytes)
Buffer-cache hash table entries: 4096 (order: 2, 16384 bytes)
Page-cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 8192 (order: 4, 65536 bytes)
CPU: Before vendor init, caps: 0183f9ff c1c7f9ff 00000000, vendor = 2
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After vendor init, caps: 0183f9ff c1c7f9ff 00000000 00000000
CPU: After generic, caps: 0183f9ff c1c7f9ff 00000000 00000000
CPU: Common caps: 0183f9ff c1c7f9ff 00000000 00000000
CPU: AMD Athlon(tm) Processor stepping 02
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
PCI: PCI BIOS revision 2.10 entry at 0xfb260, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
Unable to handle kernel NULL pointer dereference at virtual address
00000000
printing eip:
c1236000
*pde = 00000000
Oops: 0002
CPU: 0
EIP: 0010:[<c1236000>]
EFLAGS: 00010246
eax: 00000000 ebx: c1236000 ecx: 00236000 edx: 0000003c
esi: c1236264 edi: c1236284 ebp: 00000000 esp: c123dcb8
ds: 0018 es: 0018 ss: 0018
Process swapper (pid: 1, stackpage=c123d000)
Stack: c1236000 c123dfa4 00000600 c030f819 c1236000 00000000 00000000
c123dd20
03051106 c030f884 c123dd20 00000000 c123dd20 00000000 00000000
00000000
00000000 c12374c0 00000000 c030f900 c123dd20 c12374c0 c02d5fc4
c0105000
Call Trace: [<c0105000>] [<c02649a8>] [<c01070df>] [<c0107517>]
Code: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0 74 23 c1
Kernel panic: Attempted to kill init!
>>EIP; c1236000 <_end+ed6f6c/84a2f6c> <=====
Trace; c0105000 <empty_bad_page+0/1000>
Trace; c02649a8 <call_spurious_interrupt+2310/28a0>
Trace; c01070df <init+7/158>
Trace; c0107517 <kernel_thread+23/30>
Code; c1236000 <_end+ed6f6c/84a2f6c> <=====
00000000 <_EIP>: <=====
Code; c1236010 <_end+ed6f7c/84a2f6c>
10: c0 (bad)
Code; c1236011 <_end+ed6f7d/84a2f6c>
11: 74 23 je 36 <_EIP+0x36> c1236036
<_end+ed6fa2/84a2f6c>
Code; c1236013 <_end+ed6f7f/84a2f6c>
13: c1 00 00 roll $0x0,(%eax)
[7.1]
Linux linux82.integrity.com 2.4.0-test12-diskless #2 Mon Dec 4 12:03:22
MST 2000 i686 unknown
Kernel modules found
Gnu C 2.96
Binutils 2.10.0.18
Linux C Library ..
ldd: missing file arguments
Try `ldd --help' for more information.
ls: /usr/lib/libg++.so: No such file or directory
Procps 2.0.7
Mount 2.10m
Net-tools (2000-05-21)
Kbd [option...]
Sh-utils 2.0
Sh-utils Parker.
Sh-utils
Sh-utils Inc.
Sh-utils NO
Sh-utils PURPOSE.
[7.2]
processor : 0
vendor_id : AuthenticAMD
cpu family : 6
model : 4
model name : AMD Athlon(tm) Processor
stepping : 2
cpu MHz : 901.000607
cache size : 256 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 1
wp : yes
features : fpu vme de pse tsc msr pae mce cx8 sep mtrr pge mca
cmov pat pse36 mmx fxsr syscall mmxext 3dnowext 3dnow
bogomips : 1795.69
[7.3]
via82cxxx_audio 15864 0 (unused)
soundcore 4004 2 [via82cxxx_audio]
ac97_codec 7972 0
[via82cxxx_audio]
[7.4]
0000-001f : dma1
0020-003f : pic1
0040-005f : timer
0060-006f : keyboard
0080-008f : dma page reg
00a0-00bf : pic2
00c0-00df : dma2
00f0-00ff : fpu
01f0-01f7 : ide0
02f8-02ff : serial(auto)
03c0-03df : vga+
03f6-03f6 : ide0
03f8-03ff : serial(auto)
0cf8-0cff : PCI conf1
4000-40ff : VIA Technologies, Inc. VT82C686 [Apollo Super ACPI]
5000-500f : VIA Technologies, Inc. VT82C686 [Apollo Super ACPI]
d000-d00f : VIA Technologies, Inc. Bus Master IDE
d000-d007 : ide0
d008-d00f : ide1
d400-d41f : VIA Technologies, Inc. UHCI USB
d400-d41f : usb-uhci
d800-d81f : VIA Technologies, Inc. UHCI USB (#2)
d800-d81f : usb-uhci
dc00-dcff : VIA Technologies, Inc. AC97 Audio Controller
dc00-dcff : via82cxxx
e000-e003 : VIA Technologies, Inc. AC97 Audio Controller
e400-e403 : VIA Technologies, Inc. AC97 Audio Controller
ec00-ec3f : Intel Corporation 82557 [Ethernet Pro 100]
ec00-ec3f : eepro100
00000000-0009fbff : System RAM
0009fc00-0009ffff : reserved
000a0000-000bffff : Video RAM area
000c0000-000c7fff : Video ROM
000c8000-000cbfff : Extension ROM
000f0000-000fffff : System ROM
00100000-07feffff : System RAM
00100000-002d43d7 : Kernel code
002d43d8-002f67a3 : Kernel data
07ff0000-07ff2fff : ACPI Non-volatile Storage
07ff3000-07ffffff : ACPI Tables
d0000000-d3ffffff : VIA Technologies, Inc. VT8363/8365 [KT133/KM133]
d4000000-d5ffffff : PCI Bus #01
d4000000-d5ffffff : Matrox Graphics, Inc. MGA G400 AGP
d6000000-d8ffffff : PCI Bus #01
d6000000-d6003fff : Matrox Graphics, Inc. MGA G400 AGP
d7000000-d77fffff : Matrox Graphics, Inc. MGA G400 AGP
da000000-da0fffff : Intel Corporation 82557 [Ethernet Pro 100]
da100000-da100fff : Intel Corporation 82557 [Ethernet Pro 100]
da100000-da100fff : eepro100
ffff0000-ffffffff : reserved
[7.5]
00:00.0 Host bridge: VIA Technologies, Inc.: Unknown device 0305 (rev
02)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Region 0: Memory at d0000000 (32-bit, prefetchable) [size=64M]
Capabilities: [a0] AGP version 2.0
Status: RQ=31 SBA+ 64bit- FW+ Rate=x1,x2
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:01.0 PCI bridge: VIA Technologies, Inc.: Unknown device 8305 (prog-if
00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: d6000000-d8ffffff
Prefetchable memory behind bridge: d4000000-d5ffffff
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super] (rev
22)
Subsystem: VIA Technologies, Inc. VT82C686/A PCI to ISA Bridge
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:07.1 IDE interface: VIA Technologies, Inc. VT82C586 IDE [Apollo] (rev
10) (prog-if 8a [Master SecP PriP])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Region 4: I/O ports at d000 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.2 USB Controller: VIA Technologies, Inc. VT82C586B USB (rev 10)
(prog-if 00 [UHCI])
Subsystem: Unknown device 0925:1234
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin D routed to IRQ 5
Region 4: I/O ports at d400 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.3 USB Controller: VIA Technologies, Inc. VT82C586B USB (rev 10)
(prog-if 00 [UHCI])
Subsystem: Unknown device 0925:1234
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin D routed to IRQ 5
Region 4: I/O ports at d800 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.4 Host bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI]
(rev 30)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Capabilities: [68] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.5 Multimedia audio controller: VIA Technologies, Inc. VT82C686
[Apollo Super AC97/Audio] (rev 20)
Subsystem: Micro-star International Co Ltd: Unknown device 3400
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin C routed to IRQ 11
Region 0: I/O ports at dc00 [size=256]
Region 1: I/O ports at e000 [size=4]
Region 2: I/O ports at e400 [size=4]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0a.0 Ethernet controller: Intel Corporation 82557 [Ethernet Pro 100]
(rev 08)
Subsystem: Intel Corporation EtherExpress PRO/100+ Management
Adapter
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2000ns min, 14000ns max), cache line size 08
Interrupt: pin A routed to IRQ 11
Region 0: Memory at da100000 (32-bit, non-prefetchable)
[size=4K]
Region 1: I/O ports at ec00 [size=64]
Region 2: Memory at da000000 (32-bit, non-prefetchable)
[size=1M]
Expansion ROM at <unassigned> [disabled] [size=1M]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable+ DSel=0 DScale=2 PME-
01:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G400 AGP
(rev 04) (prog-if 00 [VGA])
Subsystem: Matrox Graphics, Inc. Millennium G400 16Mb SGRAM
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (4000ns min, 8000ns max), cache line size 08
Interrupt: pin A routed to IRQ 10
Region 0: Memory at d4000000 (32-bit, prefetchable) [size=32M]
Region 1: Memory at d6000000 (32-bit, non-prefetchable)
[size=16K]
Region 2: Memory at d7000000 (32-bit, non-prefetchable)
[size=8M]
Expansion ROM at <unassigned> [disabled] [size=64K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [f0] AGP version 2.0
Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2
Command: RQ=31 SBA+ AGP+ 64bit- FW- Rate=x1
begin:vcard
n:Feirtag;Fred
tel;quoted-printable;work:505 - 294 - 7747=0D=0A
tel;fax:505 - 275 - 1125
x-mozilla-html:TRUE
url:http://www.IntegrityLinux.com
org:Integrity Linux Systems
adr;quoted-printable;quoted-printable:;;1001 Medical Arts Avenue, NE=0D=0A;Albuquerque;NM;87102=0D=0A;
version:2.1
email;internet:[EMAIL PROTECTED]
title:Chief Technologist
x-mozilla-cpt:;480
fn:Fred Feirtag
end:vcard
