Signed-off-by: Ben Whitten <ben.whit...@lairdtech.com>
---
arch/arm/boot/dts/Makefile | 3 +-
arch/arm/boot/dts/at91-wb50n.dts | 116 ++++++++++++++++++++++
arch/arm/boot/dts/at91-wb50n.dtsi | 202 ++++++++++++++++++++++++++++++++++++++
3 files changed, 320 insertions(+), 1 deletion(-)
create mode 100644 arch/arm/boot/dts/at91-wb50n.dts
create mode 100644 arch/arm/boot/dts/at91-wb50n.dtsi
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 1ee94ee..fd5f8a6 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -61,7 +61,8 @@ dtb-$(CONFIG_SOC_SAM_V7) += \
at91-sama5d4_ma5d4evk.dtb \
at91-sama5d4_xplained.dtb \
at91-sama5d4ek.dtb \
- at91-vinco.dtb
+ at91-vinco.dtb \
+ at91-wb50n.dtb
dtb-$(CONFIG_ARCH_ATLAS6) += \
atlas6-evb.dtb
dtb-$(CONFIG_ARCH_ATLAS7) += \
diff --git a/arch/arm/boot/dts/at91-wb50n.dts b/arch/arm/boot/dts/at91-wb50n.dts
new file mode 100644
index 0000000..ee4f823
--- /dev/null
+++ b/arch/arm/boot/dts/at91-wb50n.dts
@@ -0,0 +1,116 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * at91-wb50n.dts - Device Tree file for wb50n evaluation board
+ *
+ * Copyright (C) 2018 Laird
+ *
+ */
+
+/dts-v1/;
+#include "at91-wb50n.dtsi"
+
+/ {
+ model = "Laird Workgroup Bridge 50N - Atmel SAMA5D";
+ compatible = "laird,wb50n", "atmel,sama5d31", "atmel,sama5d3",
"atmel,sama5";
+
+ ahb {
+ apb {
+ watchdog@fffffe40 {
+ compatible = "atmel,at91sam9260-wdt";
+ reg = <0xfffffe40 0x10>;
+ clocks = <&clk32k>;
+ status = "okay";
+ };
+ };
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ btn0@pa10 {
+ label = "BTNESC";
+ linux,code = <1>; /* ESC button */
+ gpios = <&pioA 10 GPIO_ACTIVE_LOW>;
+ gpio-key,wakeup = <1>;
+ };
+
+ irqbtn@pe31 {
+ label = "IRQBTN";
+ linux,code = <99>; /* SysReq button */
+ gpios = <&pioE 31 GPIO_ACTIVE_LOW>;
+ gpio-key,wakeup = <1>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led0 {
+ label = "wb50n:blue:led0";
+ gpios = <&pioA 12 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ };
+
+ led1 {
+ label = "wb50n:green:led1";
+ gpios = <&pioA 24 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ };
+
+ led2 {
+ label = "wb50n:red:led2";
+ gpios = <&pioA 26 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ };
+ };
+};
+
+&mmc0 {
+ status = "okay";
+};
+
+&macb1 {
+ status = "okay";
+};
+
+&dbgu {
+ status = "okay";
+};
+
+/* On BB40 this port is labeled UART1 */
+&usart0 {
+ status = "okay";
+};
+
+/* On BB40 this port is labeled UART0 */
+&usart1 {
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+};
+
+&spi1 {
+ status = "okay";
+
+ spidev@0 {
+ compatible = "spidev";
+ reg = <0>;
+ spi-max-frequency = <8000000>;
+ };
+};
+
+&usb0 {
+ status = "okay";
+};
+
+&usb1 {
+ status = "okay";
+};
+
+&usb2 {
+ status = "okay";
+};
+
diff --git a/arch/arm/boot/dts/at91-wb50n.dtsi
b/arch/arm/boot/dts/at91-wb50n.dtsi
new file mode 100644
index 0000000..11d8cc1
--- /dev/null
+++ b/arch/arm/boot/dts/at91-wb50n.dtsi
@@ -0,0 +1,202 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * at91-wb50n.dtsi - Device Tree include file for wb50n cpu module
+ *
+ * Copyright (C) 2018 Laird
+ *
+ */
+
+#include "sama5d31.dtsi"
+
+/ {
+ model = "Laird Workgroup Bridge 50N - Atmel SAMA5D";
+ compatible = "laird,wb50n", "atmel,sama5d31", "atmel,sama5d3",
"atmel,sama5";
+
+ chosen {
+ bootargs = "ubi.mtd=6 root=ubi0:rootfs rootfstype=ubifs rw";
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory {
+ reg = <0x20000000 0x4000000>;
+ };
+
+ ahb {
+ apb {
+ pinctrl@fffff200 {
+ board {
+ pinctrl_mmc0_cd: mmc0_cd {
+ atmel,pins = <AT91_PIOC 26
AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; /* PC26 GPIO with pullup
deglitch */
+ };
+
+ pinctrl_usba_vbus: usba_vbus {
+ atmel,pins = <AT91_PIOB 13
AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>; /* PB13 GPIO with deglitch */
+ };
+ };
+ };
+ };
+ };
+};
+
+&slow_xtal {
+ clock-frequency = <32768>;
+};
+
+&main_xtal {
+ clock-frequency = <12000000>;
+};
+
+&slow_osc {
+ atmel,osc-bypass;
+};
+
+&usart1_clk {
+ atmel,clk-output-range = <0 132000000>;
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_mmc0_clk_cmd_dat0 &pinctrl_mmc0_dat1_3
&pinctrl_mmc0_cd>;
+ cd-gpios = <&pioC 26 GPIO_ACTIVE_LOW>;
+ slot@0 {
+ reg = <0>;
+ bus-width = <4>;
+ };
+};
+
+&mmc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_mmc1_clk_cmd_dat0 &pinctrl_mmc1_dat1_3>;
+ status = "okay";
+ atheros@0 {
+ compatible = "atheros,ath6kl";
+ atheros,board-id = "SD32";
+ reg = <0>;
+ bus-width = <4>;
+ };
+};
+
+&macb1 {
+ phy-mode = "rmii";
+};
+
+&dbgu {
+ dmas = <0>, <0>; /* Do not use DMA for dbgu */
+};
+
+/* On BB40 this port is labeled UART1 */
+&usart0 {
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usart0 &pinctrl_usart0_rts_cts>;
+};
+
+/* On BB40 this port is labeled UART0 */
+&usart1 {
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usart1 &pinctrl_usart1_rts_cts>;
+ dtr-gpios = <&pioD 13 GPIO_ACTIVE_LOW>;
+ dsr-gpios = <&pioD 11 GPIO_ACTIVE_LOW>;
+ dcd-gpios = <&pioD 7 GPIO_ACTIVE_LOW>;
+ rng-gpios = <&pioD 8 GPIO_ACTIVE_LOW>;
+};
+
+/* USART3 is direct-connect to the Bluetooth UART on the radio SIP */
+&usart3 {
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usart3 &pinctrl_usart3_rts_cts>;
+ status = "okay";
+};
+
+&spi1 {
+ cs-gpios = <&pioC 25 0>, <0>, <0>, <0>;
+};
+
+&ebi {
+ pinctrl-0 = <&pinctrl_ebi_nand_addr>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&nand_controller {
+ status = "okay";
+
+ nand: nand@3 {
+ reg = <0x3 0x0 0x2>;
+ atmel,rb = <0>;
+ nand-bus-width = <8>;
+ nand-ecc-mode = "hw";
+ nand-ecc-strength = <8>;
+ nand-ecc-step-size = <512>;
+ nand-on-flash-bbt;
+ label = "atmel_nand";
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ at91bootstrap@0 {
+ label = "at91bs";
+ reg = <0x0 0x20000>;
+ };
+
+ uboot@20000 {
+ label = "u-boot";
+ reg = <0x20000 0x80000>;
+ };
+
+ ubootenv@a0000 {
+ label = "u-boot-env";
+ reg = <0xa0000 0x20000>;
+ };
+
+ ubootenv@c0000 {
+ label = "u-boot-env";
+ reg = <0xc0000 0x20000>;
+ };
+
+ kernel-a@e0000 {
+ label = "kernel-a";
+ reg = <0xe0000 0x500000>;
+ };
+
+ kernel-b@5e0000 {
+ label = "kernel-b";
+ reg = <0x5e0000 0x500000>;
+ };
+
+ rootfs-a@ae0000 {
+ label = "rootfs-a";
+ reg = <0xae0000 0x3000000>;
+ };
+
+ rootfs-b@3ae0000 {
+ label = "rootfs-b";
+ reg = <0x3ae0000 0x3000000>;
+ };
+
+ user@6ae0000 {
+ label = "user";
+ reg = <0x6ae0000 0x14e0000>;
+ };
+ };
+ };
+};
+
+&usb0 {
+ atmel,vbus-gpio = <&pioB 13 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usba_vbus>;
+};
+
+&usb1 {
+ num-ports = <3>;
+ atmel,vbus-gpio = <&pioA 2 GPIO_ACTIVE_LOW>;
+ atmel,oc-gpio = <&pioA 4 GPIO_ACTIVE_LOW>;
+};
--
2.7.4
