Hi Matthias,
On 2018-06-26 05:13, Matthias Kaehlcke wrote:
This is a nice improvement, a few remaining questions inline.
On Mon, Jun 25, 2018 at 07:10:10PM +0530, Balakrishna Godavarthi wrote:
In function qca_setup, we set initial and operating speeds for
Qualcomm
Bluetooth SoC's. This block of code is common across different
Qualcomm Bluetooth SoC's. Instead of duplicating the code, created
a wrapper function to set the speeds. So that future coming SoC's
can use these wrapper functions to set speeds.
Signed-off-by: Balakrishna Godavarthi <bgoda...@codeaurora.org>
---
Changes in v8:
* common function to set INIT and operating speeds.
* moved hardware flow control to qca_set_speed().
Changes in v7:
* initial patch
* created wrapper functions for init and operating speeds.
---
drivers/bluetooth/hci_qca.c | 89
+++++++++++++++++++++++++++----------
1 file changed, 65 insertions(+), 24 deletions(-)
diff --git a/drivers/bluetooth/hci_qca.c b/drivers/bluetooth/hci_qca.c
index fe62420ef838..38b7dbe6c897 100644
--- a/drivers/bluetooth/hci_qca.c
+++ b/drivers/bluetooth/hci_qca.c
@@ -119,6 +119,11 @@ struct qca_data {
u64 votes_off;
};
+enum qca_speed_type {
+ QCA_INIT_SPEED = 1,
+ QCA_OPER_SPEED
+};
+
struct qca_serdev {
struct hci_uart serdev_hu;
struct gpio_desc *bt_en;
@@ -923,6 +928,60 @@ static inline void host_set_baudrate(struct
hci_uart *hu, unsigned int speed)
hci_uart_set_baudrate(hu, speed);
}
+static unsigned int qca_get_speed(struct hci_uart *hu,
+ enum qca_speed_type speed_type)
+{
+ unsigned int speed = 0;
+
+ if (speed_type == QCA_INIT_SPEED) {
+ if (hu->init_speed)
+ speed = hu->init_speed;
+ else if (hu->proto->init_speed)
+ speed = hu->proto->init_speed;
+ } else {
+ if (hu->oper_speed)
+ speed = hu->oper_speed;
+ else if (hu->proto->oper_speed)
+ speed = hu->proto->oper_speed;
+ }
+
+ return speed;
+}
+
+static int qca_set_speed(struct hci_uart *hu, enum qca_speed_type
speed_type)
+{
+ unsigned int speed, qca_baudrate;
+ int ret;
+
+ if (speed_type == QCA_INIT_SPEED) {
+ speed = qca_get_speed(hu, QCA_INIT_SPEED);
+ if (speed)
+ host_set_baudrate(hu, speed);
+ else
+ bt_dev_err(hu->hdev, "Init speed should be non zero");
The check for 'speed == 0' is done in multiple places. From this
code I deduce that it is expected that both INIT and OPER speed are
set to non-zero values. What happens if either of them is zero? Is the
driver still operational?
[Bala]: yes in hci_uart_setup()(hci_serdev.c) function before calling
qca_setup().
we actually set baudrate, but int above code missed to restrict
the further call to qca_setup()
if speed =0. so we are checking the same in the qca_setup()..
i.e. qca_get_speed().
+ return 0;
+ }
+
+ speed = qca_get_speed(hu, QCA_OPER_SPEED);
+ if (!speed) {
+ bt_dev_err(hu->hdev, "operating speed should be non zero");
+ return 0;
+ }
+
+ qca_baudrate = qca_get_baudrate_value(speed);
+ bt_dev_info(hu->hdev, "Set UART speed to %d", speed);
+ ret = qca_set_baudrate(hu->hdev, qca_baudrate);
+ if (ret) {
+ bt_dev_err(hu->hdev, "Failed to change the baudrate (%d)", ret);
+ return ret;
+ }
+
+ host_set_baudrate(hu, speed);
+
+ return ret;
+}
In the discussion on "[v7,8/8] Bluetooth: hci_qca: Add support for
Qualcomm Bluetooth chip wcn3990" you mentioned the possbility to move
the hci_uart_set_flow_control() calls into _set_speed(). This seemed
interesting but finally it isn't done in this series. Did you
encounter that it is not feasible/desirable for some reason?
[Bala]: this patch is for rome where flow control is not used.
after we integrate wcn3990, flow control is hidden in the
qca_set_speed()
Pls check [v8 7/7] patch.
+
static int qca_setup(struct hci_uart *hu)
{
struct hci_dev *hdev = hu->hdev;
@@ -937,35 +996,17 @@ static int qca_setup(struct hci_uart *hu)
clear_bit(STATE_IN_BAND_SLEEP_ENABLED, &qca->flags);
/* Setup initial baudrate */
- speed = 0;
- if (hu->init_speed)
- speed = hu->init_speed;
- else if (hu->proto->init_speed)
- speed = hu->proto->init_speed;
-
- if (speed)
- host_set_baudrate(hu, speed);
+ qca_set_speed(hu, QCA_INIT_SPEED);
/* Setup user speed if needed */
- speed = 0;
- if (hu->oper_speed)
- speed = hu->oper_speed;
- else if (hu->proto->oper_speed)
- speed = hu->proto->oper_speed;
+ ret = qca_set_speed(hu, QCA_OPER_SPEED);
+ if (ret)
+ return ret;
- if (speed) {
+ speed = qca_get_speed(hu, QCA_OPER_SPEED);
+ if (speed)
qca_baudrate = qca_get_baudrate_value(speed);
Is the check here necessary? qca_get_baudrate_value() returns
QCA_BAUDRATE_115200 for a zero speed.
this if for no zero operating speed,
--
Regards
Balakrishna.
