On 05.07.2018 15:10, Ulf Hansson wrote: > On 4 July 2018 at 17:07, Stefan Agner <ste...@agner.ch> wrote: >> If pinctrl nodes for 100/200MHz are missing, the controller should >> not select any mode which need signal frequencies 100MHz or higher. >> To prevent such speed modes the driver currently uses the quirk flag >> SDHCI_QUIRK2_NO_1_8_V. This works nicely for SD cards since 1.8V >> signaling is required for all faster modes and slower modes use 3.3V >> signaling only. >> >> However, there are eMMC modes which use 1.8V signaling and run below >> 100MHz, e.g. DDR52 at 1.8V. With using SDHCI_QUIRK2_NO_1_8_V this >> mode is prevented. When using a fixed 1.8V regulator as vqmmc-supply >> the stack has no valid mode to use. In this tenuous situation the >> kernel continuously prints voltage switching errors: >> mmc1: Switching to 3.3V signalling voltage failed >> >> Avoid using SDHCI_QUIRK2_NO_1_8_V and prevent faster modes by >> altering the SDHCI capability register. With that the stack is able >> to select 1.8V modes even if no faster pinctrl states are available: >> # cat /sys/kernel/debug/mmc1/ios >> ... >> timing spec: 8 (mmc DDR52) >> signal voltage: 1 (1.80 V) >> ... >> >> Link: http://lkml.kernel.org/r/20180628081331.13051-1-ste...@agner.ch >> Signed-off-by: Stefan Agner <ste...@agner.ch> > > Thanks, applied for next! Let's see if this turns out okay, then let's > make it a fix and add a stable tag. > > BTW, would you mind looking up the commit it fixes? Or if there is a > certain stable release we should target. >
The quirk SDHCI_QUIRK2_NO_1_8_V has been used if pinctrl were missing since support has been added for additional pinctrl states (back around 3.13). Fixes: ad93220de7da ("mmc: sdhci-esdhc-imx: change pinctrl state according to uhs mode") I guess it won't apply on older kernels since the code which applies the quirk has been moved around. -- Stefan > Kind regards > Uffe > >> --- >> drivers/mmc/host/sdhci-esdhc-imx.c | 21 +++++++++------------ >> 1 file changed, 9 insertions(+), 12 deletions(-) >> >> diff --git a/drivers/mmc/host/sdhci-esdhc-imx.c >> b/drivers/mmc/host/sdhci-esdhc-imx.c >> index 20a420b765b3..e96d969ab2c3 100644 >> --- a/drivers/mmc/host/sdhci-esdhc-imx.c >> +++ b/drivers/mmc/host/sdhci-esdhc-imx.c >> @@ -312,6 +312,15 @@ static u32 esdhc_readl_le(struct sdhci_host *host, int >> reg) >> >> if (imx_data->socdata->flags & ESDHC_FLAG_HS400) >> val |= SDHCI_SUPPORT_HS400; >> + >> + /* >> + * Do not advertise faster UHS modes if there are no >> + * pinctrl states for 100MHz/200MHz. >> + */ >> + if (IS_ERR_OR_NULL(imx_data->pins_100mhz) || >> + IS_ERR_OR_NULL(imx_data->pins_200mhz)) >> + val &= ~(SDHCI_SUPPORT_SDR50 | >> SDHCI_SUPPORT_DDR50 >> + | SDHCI_SUPPORT_SDR104 | >> SDHCI_SUPPORT_HS400); >> } >> } >> >> @@ -1157,18 +1166,6 @@ sdhci_esdhc_imx_probe_dt(struct platform_device *pdev, >> ESDHC_PINCTRL_STATE_100MHZ); >> imx_data->pins_200mhz = >> pinctrl_lookup_state(imx_data->pinctrl, >> ESDHC_PINCTRL_STATE_200MHZ); >> - if (IS_ERR(imx_data->pins_100mhz) || >> - IS_ERR(imx_data->pins_200mhz)) { >> - dev_warn(mmc_dev(host->mmc), >> - "could not get ultra high speed state, work >> on normal mode\n"); >> - /* >> - * fall back to not supporting uhs by specifying no >> - * 1.8v quirk >> - */ >> - host->quirks2 |= SDHCI_QUIRK2_NO_1_8_V; >> - } >> - } else { >> - host->quirks2 |= SDHCI_QUIRK2_NO_1_8_V; >> } >> >> /* call to generic mmc_of_parse to support additional capabilities */ >> -- >> 2.18.0 >>